Доброго времени суток тем, кто читает этот коммент. Хотелось бы оставить отзыв об авторе данного канала. В моём случае-положительный! Обратился к Сергею за помощью, написал на почту, после недолгой переписки, Сергей попросил отправить блок управления ему для ремонта. Два дня работы, и блок был готов и выслан мне обратно, после чего его установили на автомобиль и о проблеме я забыл! Сергею выражаю огромную благодарность за профессионализм. Адекватные цены и на связи с клиентом. А для тех, кому интересно и кто дочитал до конца, проблема была такая. Автобиль Skoda Octavia a7 2014г DSG, при нагреве вылетала передача в нейтраль, а если автомобиль глушишь, то пока не остынет, не заводится.
Firstly great informations, congratulations... What can cause lost communication with TCM when it's hot? When car is cold everything is ok , when it become hot while working,losts communication with ECM.
Thank you. Error p173a is due to a malfunction of the plug magnet or a malfunction inside the electronic unit. In the next week I will post a video on errors p173a,p173b,p173c, p173d
Hi thanks for great video. on one dq200 that im playing with, i get all voltages according to the video, except for 3.3 v on the top . i also get 6.2 v instead of 7.7v next to where there is no 3.3. would the sensor cause this no voltage or the board needs some soldering
Good afternoon! Unfortunately, the video contains a little outdated data. 7.7 volts was in my case when there was a power cut to the sensor. It should be 6.2 volts like yours. 3.3 volts can also be, since this output is the direction of rotation of the sensor .It is either 0 or 3.3 is not an error.
@@scat-7842 Thank you for the reply. So if all voltages are correct as per your video, and instead of 3.3, on that top solder point, it shows 0, then what else can i look for. According to transmission shop, they changed this plate and all was good. What else can cause this plate to be faulty
Good afternoon.We need to look specifically at the loss of communication.The fastest way is to break the supply conductors, the diode may have failed or the conductors on the board going to the CAN choke have lost their conductivity.These cases have been in my practice.
Good afternoon! Flux like this-TT 20g, Flux-gel, Russia | buy at retail and wholesale (chipdip.ru) Solder like this POSK 50-18 prv d=1.5mm 100g spool, Solder, Russia | buy at retail and wholesale (chipdip.ru)
Hello, I have a tcu with code p1604, the pump motor does not work, it only makes small movements, could you tell me what to check? greetings from Mexico
I have thought that it might be something like that or a bad connection in the dsg7 controller board as its randomly loosing connection. Don't fancy replacing the whole mechatronics unit
@@michal154 Check the connection of the power contacts on the electronic unit.If the defect manifests itself intermittently, it often happens that the aluminum conductors break at the junction with the board.
@@scat-7842 i got the board out. When i took the cover i had a small surprise. The board was filled with oil. I suspect that someone was messing with the board before. Jelly that covers the board didnt like the the oil and it changed its consitency a bit. It bit more runny at the moment
I ask for a long answer - I was in the hospital. By mistake of P178B, the problem can be both in the accumulator (most often) and in the breakage of the conductors to the electric motor of the hydraulic pump in mechatronics.
Hello!! I'm following your content on RUclips, I would like to know if you have any kind of training or material to help with the maintenance of the TCM DQ200, and what would be the price of this material, I'm waiting for a response from you, thanks!
Good afternoon! Thanks for good words. The equipment I use to program the 0AM blocks is shown in this video.ruclips.net/video/QN4IPixebHM/видео.html For diagnostics I use VCDS.
@@rashadshubita1941 Launch is a multi-brand scanner. Of course, it will be sufficient for diagnostics. As far as I know, launch electronic control units for automatic transmission and DSG cannot program.
Hello! It is necessary to open the board and there will be a break in the aluminum conductor on the board. If you have never soldered aluminum, then first practice on aluminum foil.Since soldering is very very difficult! It’s also small. You will have to solder a pad measuring 1 by 2 mm. ruclips.net/video/9KePx0LelxA/видео.html
Good afternoon! It's easy to fix - you need to check the power supply of the aluminum conductors, two pieces for each line inside the electronic unit. And check the supply voltage to the processor along the circuit.
Hello! Unfortunately, now there is not enough time even for the production of a new video. A lot of work. In the next month I will release several new videos.
Наука
Nice
I have 2 units to check
Both from my car
Imagin what pain in the but it was to replace them and the cost...
Now I can test them
Thank you
Grate videos
Доброго времени суток тем, кто читает этот коммент. Хотелось бы оставить отзыв об авторе данного канала. В моём случае-положительный! Обратился к Сергею за помощью, написал на почту, после недолгой переписки, Сергей попросил отправить блок управления ему для ремонта. Два дня работы, и блок был готов и выслан мне обратно, после чего его установили на автомобиль и о проблеме я забыл! Сергею выражаю огромную благодарность за профессионализм. Адекватные цены и на связи с клиентом.
А для тех, кому интересно и кто дочитал до конца, проблема была такая. Автобиль Skoda Octavia a7 2014г DSG, при нагреве вылетала передача в нейтраль, а если автомобиль глушишь, то пока не остынет, не заводится.
Спасибо за отзыв!Был рад помочь.
Firstly great informations, congratulations...
What can cause lost communication with TCM when it's hot?
When car is cold everything is ok , when it become hot while working,losts communication with ECM.
Sorry for the long reply. First of all check the aluminum conductors inside the board.
@@scat-7842 they are not broken,all seems connected well.what should i check more? conducticity?
@@scat-7842 also some oil in board(around 5-10 cl),can it cause ?
@@scat-7842 also there is some transmission oil in pcb.Does it effects?
@@cagatayerdilmen7404 There is always oil inside - just drain it - in no case do not touch the gel
need to learn more on tcu dq200. Do you have more video's? struggeling with p073a. Nice content of good quality
Thank you. Error p173a is due to a malfunction of the plug magnet or a malfunction inside the electronic unit. In the next week I will post a video on errors p173a,p173b,p173c, p173d
@@scat-7842 thank you sir 👍👌 how do you test the mechatronics. Software? Hardware?
Hi thanks for great video. on one dq200 that im playing with, i get all voltages according to the video, except for 3.3 v on the top . i also get 6.2 v instead of 7.7v next to where there is no 3.3. would the sensor cause this no voltage or the board needs some soldering
Good afternoon! Unfortunately, the video contains a little outdated data. 7.7 volts was in my case when there was a power cut to the sensor. It should be 6.2 volts like yours. 3.3 volts can also be, since this output is the direction of rotation of the sensor .It is either 0 or 3.3 is not an error.
@@scat-7842 Thank you for the reply. So if all voltages are correct as per your video, and instead of 3.3, on that top solder point, it shows 0, then what else can i look for. According to transmission shop, they changed this plate and all was good. What else can cause this plate to be faulty
What is the error number? You need to connect diagnostics and check the sensors. Or check with an oscilloscope, if you have one.
Hi what kind of soldering machine are you using? Ultrasonic ?
what material, solder, paste or flux do you use to join the connections
he did not answer ??
Is there any electronic or electrical scheme for mechatronics?
Hello, great vidéos you do, spécial job ! I have P173E, only R and D2 works and P176A (intermittent)
Anya idea ? Thanks
👍
Thanks you for the great videos. Do you maybe have a video of the solution for U010100 lost communication with TCM
Good afternoon.We need to look specifically at the loss of communication.The fastest way is to break the supply conductors, the diode may have failed or the conductors on the board going to the CAN choke have lost their conductivity.These cases have been in my practice.
Hi
I've replaced the tcu within the mechatronic for that error
Now I have to find some time to check it on the electronic board and parts.
What flux and solder do you use to do these repairs ?
Good afternoon!
Flux like this-TT 20g, Flux-gel, Russia | buy at retail and wholesale (chipdip.ru)
Solder like this POSK 50-18 prv d=1.5mm 100g spool, Solder, Russia | buy at retail and wholesale (chipdip.ru)
Hello, I have a tcu with code p1604, the pump motor does not work, it only makes small movements, could you tell me what to check? greetings from Mexico
Fantastic job. Have you got any more details how to solve the loss of communication ?
Yes. Most often the diode fails. I will be able to post the video only next week.
I have thought that it might be something like that or a bad connection in the dsg7 controller board as its randomly loosing connection. Don't fancy replacing the whole mechatronics unit
@@michal154 Check the connection of the power contacts on the electronic unit.If the defect manifests itself intermittently, it often happens that the aluminum conductors break at the junction with the board.
@@scat-7842 i got the board out. When i took the cover i had a small surprise. The board was filled with oil. I suspect that someone was messing with the board before. Jelly that covers the board didnt like the the oil and it changed its consitency a bit. It bit more runny at the moment
@@scat-7842 which diode fails? thanks
hi very nice video keep going, how can i get voltage schematic for repair
İ want to buy kess and ktag clone , Do you have a suggestion
did you get the electrical schematic?
@@sinesiojunior5015 no bro
What about lost communication errors ? Have you made a video yet ?
Unfortunately, I'm sick right now and I didn't have time to make a video.Write questions to the mail-I will answer them.
Check the CAN line first
Do you have video for P173c ?
hi, thank you for very useful video. what do you think about P178B dtc? this is due to unexpected pressure pump behavior. thank you again
I ask for a long answer - I was in the hospital. By mistake of P178B, the problem can be both in the accumulator (most often) and in the breakage of the conductors to the electric motor of the hydraulic pump in mechatronics.
Krasaucheg
Спасибо!
Hello!! I'm following your content on RUclips, I would like to know if you have any kind of training or material to help with the maintenance of the TCM DQ200, and what would be the price of this material, I'm waiting for a response from you, thanks!
Do you want the material？
Hi,
thank you for very much for this useful video. BIG LIKE and SUBSCRIBE!
Can I know the software you use and how to connect it to TCU?
Good afternoon!
Thanks for good words.
The equipment I use to program the 0AM blocks is shown in this video.ruclips.net/video/QN4IPixebHM/видео.html
For diagnostics I use VCDS.
@@scat-7842
Thanks for your response, you deserve each word!
Okay, I buy launch x431 pro5(on the way) can do this ? or need this hardware?
@@scat-7842 Also reading TCU sensor data done by VCDS, right?
@@rashadshubita1941 Launch is a multi-brand scanner. Of course, it will be sufficient for diagnostics. As far as I know, launch electronic control units for automatic transmission and DSG cannot program.
@@rashadshubita1941 Yes.The program in the video is in Russian, but the principle of operation is clear
Can you show the stuck in gear 6 or shifr fork c trouble codes?
I don’t understand. Should I show the repair or the code number? If the code number of the plug is 3, then it is P1731
Do you have a video for lost in communication of tcm in dq200
Good afternoon! The video will be released in a week.
I got the P0715 00 on a DQ500, do you have any guide? Thanks!
Hello!
It is necessary to open the board and there will be a break in the aluminum conductor on the board. If you have never soldered aluminum, then first practice on aluminum foil.Since soldering is very very difficult! It’s also small. You will have to solder a pad measuring 1 by 2 mm.
ruclips.net/video/9KePx0LelxA/видео.html
@@scat-7842 Ok perfect! I got it! thank you for your time. :D
Hi sir pls tell me about code p175E/05982 in audi a1 1-3-5-7 gear not shifting
Unfortunately with this code did not repair
Thanks but it's showing clutch 1 closes unintentionally
How do you fix output driver IC error?
P1604
replacement only
Hello sir is it possible to fix an ECU with fault code P0562 voltage too low ?
Good afternoon! It's easy to fix - you need to check the power supply of the aluminum conductors, two pieces for each line inside the electronic unit. And check the supply voltage to the processor along the circuit.
Would you please explain further on this i have this fault on my car how can i fix it
@@franciscochilambe1927 Send me a photo inside the electronic block by mail repairecu123@gmail.com - I will mark the problem areas in your block
I have a p0615 error code, what i can do?
1:25 You sell this handout with the repair information
Hello!
Unfortunately, now there is not enough time even for the production of a new video. A lot of work. In the next month I will release several new videos.
Seriously aged
Hello, how can I contact you? I am from mexico
Hello! My mail repairecu123@gmail.com