How to download the Librepilot and setup CC3D flight controller.
HTML-код
- Опубликовано: 5 окт 2024
- #cc3d flight controller #librePilot #Openpilot
Download Librepilot directly from my google drive : drive.google.c...
Hey guys, IN this i showed how to download the librepilot GCS and program the cc3d right from the beginning specially for beginners with explanations on each step which will guide you to successfully make your drone fly with cc3d flight controller. As this is the 3rd part of QAV250 build with cc3d flight controller series and only consists of the programming and calibration procedures, you should watch my previous Part 1 and part 2 fin which i have showed and explained the assembly process as best as I could do.
QAV 250 build, Assembly Part 1:
QAV 250 build, Assembly Part 2:
I have put a lot of efforts making these Videos so please don't leave without Leaving a Like and Subscribing my channel.
Thank you very much for your time.
Creative Nischal
Creativenischal
Please Like, Share, and Subscribe.
Please share your thoughts here in the comments section...
Sir, can u tell me how to complete the librepilot without the companys settings flie because there website doesnt exist
You are using Librepilot... If I use openpilot......which is best?
You should use librepilot because open pilot has officially stopped and you cant get this software from its original website so use librepilot
@@AmateurInventor Thank you so much
You are most welcome 😊
thanks for the video!
It's my pleasure 😊
good job
Thank you very much, please consider subscribing this channel. Thanks once again🙂
mine can't connect, I have to download which file so I can connect to librepilot.
I think you may be having problem with bootloader
@@AmateurInventor botleader is a kind of file, what settings are not correct
@@masyantuk i didn't completly understand what yoy wanted to say. Please make me clear about your problem.
@@AmateurInventor My problem is I can't connect, but what kind of file is the bootloader?
Bootloader is a file/program which tells your computer where to look for instructions, exchange data before you connect your FC with librepilot GCS. You must be having the bootloader issue.
Bro ek video cc3d me gps kaise lagai hot Return to land function Ko kaise enable kare
Bro CC3D me APM jaisa sab kuch nahi kiya jaa sakta. Agar tumhare cc3d mai barometer hai toh hi return to land kar sakte hai warna nahi hoga
Why I can't save the settings on last
Maybe you have problem with your Device bootloader. Search for bootloader issue
Nice presentation.
Many many thanks
Amazing video thanks for video
You are welcome brother..
What about librepilot and the rise rxs255 quadcopter? Can u mame an instructional video for that one?
Pleaae share brief description of your quad with mee and also send it's pictures on my g mail
hi there i desperately need help, as soon as i try opening libre pilot it shuts it self down, it takes a couple of attempts to finally open it, once opened my home tab is just a black screen, however i am able to access a couple of the tabs like the download one. thanks,
Bertie
I have seen people with similar problem. The root cause is incomplete download. Although its shows the file has been successfully downloaded, but it is not. Try downloading it on another device, move to your pc and later try to install it on your main device. The. It should work
Hi, Sir I have downloaded libre pilot 16.9 version gcs and started with vehicle setup . Everything was fine untill prompted to save settings to cc3d .After clicking save it stopped like showing "Preparing mixers"
Please kindly help me I need your help 😢
Hey, it seems you got bootloader issue on your flight controller. You can once try and upload an new bootloader onto your flight controller and try doing vehicle setup once again. Let me if it works or not.
@@AmateurInventor yeah may be but I was trying with different bootloaders like etucc3d_200.bin and its been 4hours since I started with it . Very frustrating issue
You may once try to follow up video by robojax on replacing the bootloader... You can send me pictures at my mail creativenischal@gmail.com for further help
@@AmateurInventor please recommend a good bootloader for cc3d and steps further so as to not to struck with same "preparing mixer "
Video by ribojax is really helpful. You may try that one too...
I am not able to upgrade firmware in libre pilot it's showig
"Timed out while waiting for a board to be fully connected! You will have to manually upgrade the board using the uploader plugin."
Also Rx & Tx is not showing please help me sir
Brother i had the same issue when i got cc3d in my first drone. The solution is preety simple. You need to re flash bootloader into your cc3d board. I will provide you the link to watch this shortly
ruclips.net/video/_cJx1NodY8c/видео.html
Please consider subscribing it it helped ☺️
Hi nice explanation. I'm trying to configure the FC. At time 6.2 the output calibration for motor, I'm getting it neutral rate at different microseconds for all for motors. Will it be a concern or what could be the problem ?
This should be this way. It is this way so that when the throttle is at the minimum, the motors start spinning at the same time. It's fine. You don't need to worry!
@@AmateurInventor thanks. That means the controller get to know when to start all the four motors to spin at same time. Am I correct ?
@@basics5823 exactly 😃
@@AmateurInventor thank you for the immediate reply.
You're most welcome 🤠
Hi, I followed the same procedure but at the last (save step) it got stuck saying "preparing mixer settings" can you help me with this !?
By the way amazing video !
Thank your for your comment. It really means a lot to me.
Please briefly explain the problem and send me a shree shot of laptop screen on creativenischal@gmail.com
Or whatsapp 9814881110
So i can help you with that
I found a similar video on RUclips ruclips.net/video/RCBHXR_F7Rs/видео.html (same problem I had)
plese subscribe and share to your friends if possible 😃
ruclips.net/video/_cJx1NodY8c/видео.html.
I think your firmware on cc3d is broken
I contacted you I have help me cc 3 d me gps ko kayse lagaye please tell me Hindi
Hey, you can check out a video from painless 360. He has shown to add a gps in CC3D in one of his videos very clearly. I am not getting time these days to make any videos.
I meant can u make and instructional video...
I can certainly do it but Nowadays I am too busy in an another project... For now I can recommend you videos from another creators.. please give me some time
How do i send you an email
creativenischal@gmail.com
To this mail
I have a mac 😒 it’s not support it
This tutorial is for the windows pc
I downloaded the software as u showed, after installation the application is not opening, can u help me in this regard?
Ok! Just tell me where you stuck?
@@AmateurInventor when i open the software it just shows application starting that's it and dissappears, how may time i try it's the same
Ok! I had this issue with one of my friend. It is because of incomplete download. a slow internet might me a reason. Which browser are you using? Maybe try an another browser. It might help😊
Ok i'll do that and if u have the software, could u please put it in our description as a zip file may be ?
Ok!
i did exactly what ytou said and followed your instructions to the letter and when i clicke don "upgrade" it loaded SOMETHING into the board and when it completed now my board is unrecognized and nothing works. You bricked by BRAND NEW flight controller.
Look Brother, it is the process to flash the board. If it is bricked then it is bootloader issue in your flight controller. But do not worry, it can also be fixed. I'll send you the video which will help you😀
@@AmateurInventor I would appreciate that.
Follow this video and your problem will be solved😊 ruclips.net/video/_cJx1NodY8c/видео.html
@@AmateurInventor cool. Thank you.
You're welcome and do consider subscribing if it helped😊