To był jakiś pająk z podstawką do 8-nóżkowego chipa pod stary serial. Z tej samej strony co schemat pinpointera. Później kupiłem taki uniwersalny TS8900-K150. Oba działały.
Hello my friend, i see you made a coil on ferrite, when you move the detector like east - west - north - south - up and down.... doesent this effect the detector? beeping without have mettal close to it? I ask because i made also a coil on ferrite and it is effected by magnetic fields of the earth, Than you in advance for your respond.
Hi. There must be ferrite as shown in the picture, i.e. with a hole in the center, such as from the monitor cable. Then there is no reaction of the Earth's field when rotating the detector. You can only distinguish metals with smaller items (coin). With larger ones, it always shows me the color. The author of the project himself described it like that and I don't know if he has improved anything in the meantime.
Hello dear brother, thank you very much for teaching us how to make a metal detector. I ask you, if possible, to teach us a metal detector to build two meters of metal underground, because in our area, all gold is less than one meter to three meters. May God grant success to you and your dear family, and may you always be victorious and happy in life, brother
Por favor, pode dar mais detalhes da bobina? são duas camadas de fio 0,3mm, 100 voltas cada camada, num diâmetro de 16mm ? elas foram enroladas em um tubo oco de ferrite 16mm? não ficou claro esta parte. Agradeço se poder responder.
Para a bobina, você precisa de ferrita do filtro de cabo. Normal reagirá ao campo da Terra. Para mim, 16 mm de diâmetro, cerca de 200 voltas com fio de cobre de 0,2 mm (duas camadas saíram com um comprimento de cerca de 3 cm e uma resistência geral de 10 ohm). O capacitor deve estar em torno de 20 kHz, o que é o que o autor supôs.
Dodam tylko, że ostatnio świetnie sprawdził się przy szukaniu gwoździ w starej instalacji elektrycznej. Gwoździe są żelazne a przewody aluminiowe lub miedziane. Same przewody widzi w kratkę bo są jednak już zbyt cienkie ale gwóźdź (jego główkę) widzi ładnie. Nie trzeba pruć całej ściany ale wystarczy przelecieć wykrywaczem po ścianie i wykuwać punktowo. Mniej roboty i brudu.
Many thanks for your order, but sorry to bother you to confirm 2 issues. 1) In the enclosed picture 1, we will ignore the blue outline on the BL layer(indicated by arrow) and use the white outline to fabricate, is it OK? 2) In the enclosed pictures 2&3, we found below issue. Is it a mistake?? BO layer matches TS layer TO layer matches BS layer But actually, they should be: TO layer matches TS layer BO layer matches BS layer Please clarify which is BO layer, and which is TO layer. And for the correct BO layer, do you need us to mirror it for you?? if you interested I can send you photos
@@trkbellikli Sorry, but i am not expert in this point. Only scheme in 1:32 of movie is original and working perfect. My PCB project is the same (but then I aded some regulators to test old soft). Second layer was made for switch, buzzer and led but cable will be ok to. Rest problems is to hard to me to understand. This PCB project was my first in life :).
@@puchan1969 Dear Punchan Im also not expert or professional, Im amateur and liked your desing and want to make it. So I already ordered and said to them, just do it like this. I will assembly it, I only want you help me while I m assembiling.
@@trkbellikli OK, write if You will have problems. Remember You need 2 aku 3,7V. Project is for 9V (5-9,5V). Mine are shorter version of popular 18650, 16340. For 2x18650 You need longer pipe. Ferrite from cable filter with hole inside, no antenna version without hole. And film capacitors brown or green i two places: 100 nF i 33 nF.
@@puchan1969 Thank you . I have got today PCB's from jlcpcb. I uploaded photos, could you please look at thats, any problem you see. resmim.net/f/1odYlm.jpg resmim.net/f/8ipXQD.jpg
سلام دوست عزیز من در ایران زندگی میکنم آیا برای شما این امکان را دارد که یک نمونه از این دستگاه فلزیاب بسیار عالی را برای من در ایران ارسال کنید از شما خواهش میکنم 🙏❤️🖐️
This is not my knowledge but the author Eddy71 from Ukraine. Link below: md4u.ru/viewtopic.php?f=8&t=3977&start=725 Only the narrow PCB design is mine.
The best pin poiter i seen
Wow ,,, nice project, good project.
Its not mine project, only costruction.
مدهل شكرا
Waw naic❤
what is the program for the chip
drive.google.com/file/d/0B6VI6ThBC8EMTmRCTEpFdG96TzA/view?resourcekey=0-3VZhwJYVViK_Wzvhveh9MQ
Hi friend. What's performance coil ?(please help me
Na jakim programatorze zaprogramowałeś układ😁
To był jakiś pająk z podstawką do 8-nóżkowego chipa pod stary serial. Z tej samej strony co schemat pinpointera. Później kupiłem taki uniwersalny TS8900-K150. Oba działały.
Hello my friend, i see you made a coil on ferrite, when you move the detector like east - west - north - south - up and down.... doesent this effect the detector? beeping without have mettal close to it? I ask because i made also a coil on ferrite and it is effected by magnetic fields of the earth, Than you in advance for your respond.
Hi. There must be ferrite as shown in the picture, i.e. with a hole in the center, such as from the monitor cable. Then there is no reaction of the Earth's field when rotating the detector. You can only distinguish metals with smaller items (coin). With larger ones, it always shows me the color. The author of the project himself described it like that and I don't know if he has improved anything in the meantime.
@@puchan1969 Thank you my friend, i did it also with ferrite from cable and it is working great.
Hello dear brother, thank you very much for teaching us how to make a metal detector. I ask you, if possible, to teach us a metal detector to build two meters of metal underground, because in our area, all gold is less than one meter to three meters. May God grant success to you and your dear family, and may you always be victorious and happy in life, brother
For gold 2 meters undergound you need 2 meters long detector... ;)
Por favor, pode dar mais detalhes da bobina? são duas camadas de fio 0,3mm, 100 voltas cada camada, num diâmetro de 16mm ? elas foram enroladas em um tubo oco de ferrite 16mm? não ficou claro esta parte. Agradeço se poder responder.
Para a bobina, você precisa de ferrita do filtro de cabo. Normal reagirá ao campo da Terra. Para mim, 16 mm de diâmetro, cerca de 200 voltas com fio de cobre de 0,2 mm (duas camadas saíram com um comprimento de cerca de 3 cm e uma resistência geral de 10 ohm). O capacitor deve estar em torno de 20 kHz, o que é o que o autor supôs.
@@puchan1969 Muito obrigado por sua atenção e por responder no meu idioma.
Nice
Dodam tylko, że ostatnio świetnie sprawdził się przy szukaniu gwoździ w starej instalacji elektrycznej. Gwoździe są żelazne a przewody aluminiowe lub miedziane. Same przewody widzi w kratkę bo są jednak już zbyt cienkie ale gwóźdź (jego główkę) widzi ładnie. Nie trzeba pruć całej ściany ale wystarczy przelecieć wykrywaczem po ścianie i wykuwać punktowo. Mniej roboty i brudu.
Witam,czy można kupić tę pointer
@@nikvido1504 Niestety nie. Zrobiłem dla siebie i często się przydaje w domu.
How sir?
Map please
Qual a referencia desta peça branca no circuito?
Este Pinpointer é muito instável..Apita até sozinho ..montei tudo certinho , fiz a blindagem da bobina ..Nada resolveu..
That's great! Will you try goldnuggets,,,
Golden rings and magnetic stones....
dear Puchan are you here, I want to ask some question. I have sent your modification to jlcpcb and they asked me some question
Many thanks for your order, but sorry to bother you to confirm 2 issues.
1) In the enclosed picture 1, we will ignore the blue outline on the BL layer(indicated by arrow) and use the white outline to fabricate, is it OK?
2) In the enclosed pictures 2&3, we found below issue. Is it a mistake??
BO layer matches TS layer
TO layer matches BS layer
But actually, they should be:
TO layer matches TS layer
BO layer matches BS layer
Please clarify which is BO layer, and which is TO layer. And for the correct BO layer, do you need us to mirror it for you??
if you interested I can send you photos
@@trkbellikli Sorry, but i am not expert in this point. Only scheme in 1:32 of movie is original and working perfect. My PCB project is the same (but then I aded some regulators to test old soft). Second layer was made for switch, buzzer and led but cable will be ok to. Rest problems is to hard to me to understand. This PCB project was my first in life :).
@@puchan1969 Dear Punchan Im also not expert or professional, Im amateur and liked your desing and want to make it. So I already ordered and said to them, just do it like this. I will assembly it, I only want you help me while I m assembiling.
@@trkbellikli OK, write if You will have problems. Remember You need 2 aku 3,7V. Project is for 9V (5-9,5V). Mine are shorter version of popular 18650, 16340. For 2x18650 You need longer pipe. Ferrite from cable filter with hole inside, no antenna version without hole. And film capacitors brown or green i two places: 100 nF i 33 nF.
@@puchan1969 Thank you .
I have got today PCB's from jlcpcb. I uploaded photos, could you please look at thats, any problem you see.
resmim.net/f/1odYlm.jpg
resmim.net/f/8ipXQD.jpg
nice idea
Please prepare make one by one soldering with names of all Component's. Thanks
Excelente 👏 também montei o mesmo projeto de Eddy
Bana yardımcı olabilir misin ben yaptım ama sürekli tekrar ediyor program çalışmıyor
سلام خسته نباشید استاد اگه امکان داره ساخت پین پو ینتر به فارسی هم برامون بذارید ممنونم
זה מאוד קל. אותו דבר כמו בפולנית.
سلام دوست عزیز من در ایران زندگی میکنم آیا برای شما این امکان را دارد که یک نمونه از این دستگاه فلزیاب بسیار عالی را برای من در ایران ارسال کنید از شما خواهش میکنم 🙏❤️🖐️
كيف حالك
لديكم جهاز البولوني الايراني انه جهاز ممتاز
Benim devrem sürekli tekrarlıyor ne yapabilirim
Merhaba dostum devreni çok beğendim şema ve yazılım linkini dilinizi bilmediğim için bulamadım likleri burada paylaşırsan sevinirim
Publique a lista de materiais,
Sir, I am permitted to develop your knowledge ... may God repay your kindness
This is not my knowledge but the author Eddy71 from Ukraine.
Link below:
md4u.ru/viewtopic.php?f=8&t=3977&start=725
Only the narrow PCB design is mine.
@@puchan1969 siema jakim programatorem to zaprogramowałeś? i jakim programem?
@@szczurwodny4473 W linkach wszystko jest pod filmem. Programator taki z Chin na PICa. Ale można zrobić swój, dosyć prosty. Program z linków.
Boa noite onde posso comprar esse Pinpointer e qual valor
Everything is in the links.
what the modification bro
150 zł daje zrobi ktoś ?
Bisakah saya beli alat itu
Berapakah harga nya
لطفا نقشه مدارهات را بزار
Ile chcesz za niego 🙂
Nie sprzedaję, za dużo serca w to włożyłem. No i jak mam czas to wyszukuję nim i wyciągam gwoździe ze starej instalacji elektr.
Mantaf ,bisa membedakan logam emas dan yang lainnya
Kalau beli kemana itu ,bos?
Bisakah saya pesen 1
Halooo bro kasih skemanya ngblur ga jlas
А почему все комменты на не Русском?
A pacziemu nie na Ukrainskom? On ukrainskij.
А вы пидарасня хотите что-бы всё и везде было по педаруски.
Потому что большинство из нас не из великой России.Я из Ливии и хотел бы увидеть русские изобретения потому что у вас отличные изобретения