Ford 8.8" Differential Complete Tear Down
HTML-код
- Опубликовано: 16 июн 2016
- All of the information in this video will also apply to the GM 12 bolt as well as other differentials of this type.
The #FairmontProject needed a new differential. The stock 7.5" wasn't going to cut it. So I got an 8.8" out of an '86 Mustang. The Mustang rear end had Traction-lock, but I'm not reusing that carrier. Since I'm upgrading to 31 spline axles, I needed to upgrade it anyway.
Perhaps at some point I'll go back and do a rebuild of the stock traction-lock differential, but since I was upgrading anyway, it really wasn't necessary.
***I show how to make a 'set up' bearing in this video. I learned the hard way that this may not always work out. If you are going to use a set up bearing, I recommend purchasing 2 new pinion head bearings and using one for set up. You can purchase set up bearings separately, but they are way more expensive than just getting a second bearing.
The best place for answers to your automotive questions: www.ericthecarguy.com
Camera: Brian Kast
Thanks for watching!
Discussion about this video: www.ericthecarguy.com/kunena/1...
Useful info
Ford 8.8 PDF: performanceparts.ford.com/dow...
A great book on Differentials: www.amazon.com/Ford-Differenti...
Tools
Brake Tools: www.jbtoolsales.com/atd-tools...
Slide Hammer: www.jbtoolsales.com/sunex-391...
Axle Bearing Attachment: www.jbtoolsales.com/astro-pne...
Bearing Splitter: www.jbtoolsales.com/cta-tools...
20 ton press: www.jbtoolsales.com/sunex-too...
Pinion Flange Holder: www.summitracing.com/parts/aaf...
Zep Penetrating Oil: www.zepautomotive.com/product/...
Related Videos
Fairmont Playlist: • ETCG Gets a New Car! -...
Rear Brake Replacement (Drum): • How To Replace Drum Br...
Hoarding Parts: • Hoarding Old Parts -ETCG1
**Answers to your automotive questions found here: www.ericthecarguy.com/faq
Social Network Links
Facebook: EricTheCarGu...
Twitter: / ericthecarguy
Google+: plus.google.com/1001951801966...
Instagram: / ericthecarguy
Information on Premium Membership: www.ericthecarguy.com/premium...
Stay Dirty
ETCG
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy. 
Авто/Мото
i`ve watched a lot of car programs on tv and your channel is the first one that shows work being done and tools actually being used not a load of mechanics moaning to each other about the job an timeline. Great channel i`m clueless when it comes to cars but find your video great to watch the engine swap videos got me started on your channel
Thank you!
I'm in the process of rebuilding a Ford 8.8 to put under my Mustang. I've watched this video probably 2-3x already and I'm sure I will again before the jobs done. Very helpful for a novice mechanic.
Your excitement for this project is palpable, and it makes the videos fun to watch. Your videos feel more upbeat and humorous of late. Keep it up!
Sir you are so detailed with your work along with good energy, your videos are very inspiring.
Keep up the great videos Eric.
Great video Eric, nice too see you so happy working on something again. Looking forward to the rest of the fairmont vids.
Definitely one of the best videos I’ve seen on the teardown process. I enjoy these videos, Eric.
Eric, you did a great job on showing all the different tools a person needs to work on the differential and you hit on all the important points of marking the parts so it all goes back together correctly also thanks for showing your work instead of fast fording to the end to save time .... Stay safe and stay dirty !!!!!!
*SOOO NICE*- to see you back at your Shop, and back to work on Oliver! Eagerly awaiting more of this series. THANK YOU, ERIC.
Thanks Eric for putting the Ford 8.8 videos up. A couple years ago I acquired a '93 F150 base model with the tried/true combo of the 300 six, M5OD and 8.8 rear with 3.55 gear set. The previous owner drove it with a totally destroyed rear u-joint. After I went through the truck I noticed that on short runs at highway speed the diff was getting abnormally hot up around the pinion bearing(s). No noise or other symptoms. I'm suspecting that bad u joint trashed at least the outer pinion bearing. Thanks to your helpful videos on teardown and setup (in addition to a factory service manual), I feel confident that I can do a rebuild.
I'm really looking forward to the rest of these 8.8 videos. I have two 8.8 axles that need to be rebuilt. These videos will help me decide if I should take them to the axle shop to get them done or if I should invest in the tools to do them myself.
Great and enjoyable disassembly as always. Looking forward for the next parts.
Changing my 2000 ford ranger 4x4 to an FX4. 31 spline from a 28 spline with spartan lockers. Eric you are definitely an excellent teacher thank you.
Thanks for making this video Eric. I'm currently attending a trade school, doing the automotive program at Universal Technical Institute and I'm in manual transmission learning about differentials.
Good luck in school and thanks for your comment!
Eric, Thank you I've got a 94 Explorer(8.8) with a leaking axle seal that i'll be replacing in the morning. This video was right on time.
Im a jeep guy and this is a very popular swap for XJ/YJ/TJ jeeps. This is the best junkyard 8.8 tear down i have seen yet. way to go ETCG!
Thank you for this series. It was the difference between selling my truck to pull a part, & putting it back on the road. I'd have never tried to rebuild a differential without videos like these.
Watched you last night and today I pulled my very first diff apart. Keys were missing but I got really lucky and when I pulled the cover off the pin retainer screw was right there and I didn't have to remove the drive shaft. I was just going for the carrier to swap my ring gear onto but you gave us everything
Have assisted in building a 12 bolt and a couple 9 inch rears. So interesting to see an 8.8. Didn't know they shared anything with a 12 bolt. Looking forward to the rest of this series. Setting rear ends up was probably the most time consuming/precision thing have ever done on cars, as if not done right, esp on a performance car, it will cost you. Heh wish youtube would have been around then, would have helped alot.
In the beginning you called it a posi-trac. I was losing my mind trying not to correct you, so I kept watching. You specified the Trac-loc (l/s) and a weight lifted off my shoulders. Thank you for being knowledgable.
OOOOOOH! The Fairmont project is starting to get REEEEEALLY GOOD! Chompin' at the bit again... but enjoying the journey as well. THANKS!
I watched this nearly a year ago to get to the part about removing the axles. Now I'm back to rebuild the insides. Great content.
It's amazing to see how happy he is in these videos. Probably because he's building his baby finally.
Oh man this was a great video! I don't know much about differential rebuilding so I definitely learned something. Looking forward to the subsequent videos!
I love the smell of Gear oil. I miss going to school to study this. I loved the power train classes. I can't wait to see how you do what you want.
He's chill like that, definitely earned a follow off chillness
this time on eric the car guy, how to do a pinon reach around on fords rear end
Eric you are just like me. "I'm going to hang on to these because one day down the road I might need a part from in here." it just happens that you hang onto it for 6 months finally throw it away and one week later you have a reason to need it. never ever fails
ruclips.net/video/EdKH2NzzkNs/видео.html
hey Eric the car guy. I'm 17 years old and from Indiana. I plan to be like you 1 day. I go to college this year's for automotive. you have helped me soo much!!
Love Eric's video have been subbed and watched for years. Sometimes I forget to thumbs-up them when I watch them but when he made the tractor beam sound and said "amber vision" i scrambled for the thumbs up. Even though without it Eric would have gotten the thumbs up.
You seem just a bit giddy doing this.
Honestly, I've seen some of this before, but this was a very comprehensive and well-shot video. Thank you.
I really enjoyed this video Eric. I learned a few things about differentials that I didn't know, thanks.
Thanks for sharing
Roy
Glad to hear it. Thanks for your comment.
Wish you were near me. I would work for you for free just so I could learn what you know. You are a great mentor and father figure. Keep up the good work Eric.
Eric, you're like the Bob Ross of auto mechanics: your canvas is your workshop and your medium is cars.
I love Bob Ross. R.I.P. I take that as a complement.
Just needs to get the voice down...
"...and right nestled down there is another little shim... we'll paint it ochre"
+Deathlok67 You win! that is the comment of the day.
I was just thinking something along similar lines right before reading this excellent post. Eric inspires me all the time.
I used to always watch him as a kid. He got me painting pretty well. Now I couldn't paint to save my life.
OMG OMG OMG! I have never hit play so fast. I'm actually early for an ETCG video for once! The last time I came this fast, my girlfriend left me. Roll on the rest of the Fairmont videos!
Hahaha. I just want them All. NOWWW!
Thanks for the heads up on those bearing caps!
great video eric, definitely a nice break from these pull a part videos, lol. keep up the good work man!
This is awesome! Thanks for the teardown Eric!
Thank you Eric. Your videos are always very informative.
Just watched this for the third time, getting ready for my tear down on my ‘86 Mustang 5.0. Wish me luck!
Nice attention to detail,it really made your video stand out.
This humor of yours, I really love it!
you were positively giddy in this video. nice to see :)
Great video as usual,you're not a pack rat, your smart, i do the same thing, i have a cardboard box where i have tons of Mustang parts, springs, screws,levers, brackets, you name it,even light bulbs,those parts have come in handy more than once specially now these cars and their family like your Fairmont are getting scarce.
I replaced an axle on a 2000 E150 - sans limited slip! - purty much like this.
The air hammer/chisel is pretty much the tool 'o' the century!
Nice vid!
Another great video! Like the rest of us, you certainly are happier working on a project that has nothing to do with work. I really enjoyed this one...
Finally Fairmont videos :D The long awaited chapter begins :D
great tips eric, i always learn something watching your videos
You are a born teacher. Superb detail. Thank you!
A quick and easy way to remove the e-brake cables from backing plates is to slide a boxed end wrench over the expanded tangs, I think 1/2'' wrench for most. It compresses them all at the same time and the cable pulls right out. Beats fighting them with a screw driver.
Good old "80-90 Stink"! I agree I hate that smell too!
Just wanted you to know that I learned a couple of things. I learned how to use my brake spring tool! I've done my fair share of drum brake jobs too. I haven't see the offset box end wrenches like you used. Thanks!
new Fairmont video, my Friday just got better.
i like watching these videos. they teach me something everyday.
Great job Eric!
Thanks!
I use a paint roller. hammer the handle arm flat. spray brake cleaner in tube and push debris to center. clean it out. makes for a great, clean tube assy. Be sure to pack outer wheel bearings with axle grease due to it taking a while to lube. If not you'll burn up outer axle bearing. Great video AS ALWAYS ERIC!!
Eric, noticed you when you were pressing out that pinion bearing, that the support blocks you pressed from were on the bolt heads of the bearing puller, instead of parallel with the bolts. Naughty.
You're doing it wrong!!! Yea, I get that all the time.
Still enjoy watching these videos, especially this diff. rebuild, because guess what I'm doing next year! Love your work.
I see a future Pull-A-Part video coming. LOL. JK Eric. I'm one of the few that liked those videos...
Hi, just replaced all the bearings in my Lincoln Town Car that uses the same differential. Your video was great advice so I knew what was coming and what to look out for. It went smooth but I did it with the differential in the car and only jack stands, no lift. It was no fun but doable. Had to improvise regarding the preload on the pinion bearings since I have no lb/in or cNm torque measurement tool and they are about 300$+ overhere. I worked with a thin and light wooden bar and weights and did some math.
Also, no press but heating the bearing to 200F in water and freezing the pinion gear and carrier in the freezer was enough to let the bearings glide on with no effort. Physics and math can sometimes replace expensive tools! The differential works absolutely fine now and I was abel to do it on a weekend. Best regards from Germany.
Great video Eric that air hammer sure saved you some sweat and blue language there.
I did similar work 12 years ago on my dif. while hanging in the car. the top bushings were a pain in the butt to get out even with the air hammer.
I am really liking the direction of this build mostly because I love old Ford cars and trucks, also I like a good sleeper. I'll bet it's going to be fun on the street with 5 speed
Very informative, well laid out video. Thanks very much!
Hey Eric,I wanted to say I use a box end wrench to take them type of parking brake cables off. I just slide the one that fits over it down, and it pulls the tabs in and you can just slide the cable off, that is if your gong to reuse them.
Most comprehensive video I've found thank you
Excellent content, thank you for uploading.
That was amazing! I owe you for all this knowledge sharing, sir!
He drinks Jack Daniels lol
Someone may have mentioned this before, but the damage on the crush sleeve was from the fragment pieces you found inside the case. You could see them near the sleeve location when the pinion bearing races were being hammered out. Sorry if this was a repeat comment. Love to watch you work, Eric... hate to have to do the same thing myself as a follow up.
Looks to me like you might have done that a few times there Eric. Actually I have never had to pull a rear end apart so this was very informative in case i even wanted to do a rear end swap. Thanks for the video
Very informative video Eric. Thanks.
Thanks for another great video! On getting the smell of dif oil out of your skin, I use 50/50 pine sol/water then dish soap. Seems to do a pretty good job!
You seemed much happier than normal in this video. Must be working towards your end goal of the high preformance "sleeper" has you smiling more!
I've found I like building things more than I like fixing things lately. ruclips.net/video/lFhCSxFdkT0/видео.html
+EricTheCarGuy Building things is spending money, fixing things is making money, for me I like spending more than making! lol
Thank you Eric. Your teaching is very clear.and I do diy.
Damn. Not sure how but you're always working on exactly what I am when I'm doing it. I had my Outback that's when I found and subbed your channel and learned everything I needed for that. Now I have a Ford with an 8.8 that needs rebuilt look today and here you are rebuilding one. Hahaha
Hey Eric congrats on the 800k subs!!!
I like the way you work on that.
awesome. cant wait to see the paint video and the assembly. I hope you are going with a Detroit trutrack :)
this gives me an idea of what im going to face on my project thank you!!!!
Those wheel bearings can be tough - I nearly pulled my truck sideways off the jack stands doing that job once. If you can't get the bearing out just cut it with a die grinder to release the bite and it will slide right out. Its always good practice to mark the caps - every axle I've happened to take apart has always had letters on each cap and on each sealing surface of the diff.
Thank you again Eric this is a great vid for what my ford 8.8 will do to my chevy s10.
Good video - learned quite a bit!!
In your video about progress on the Fairmont you stated that you had shot more than 60 videos at that point on the car. I hope these video come out more than once a week, or we're all going to be a lot older when this is done LOL. Love your videos!
Some will.
A few years ago my outer pinion bearing in my 01 Durango's rear axle, it howled all the way home. I helped my dad replace the pinion and carrier bearings at home ourselves, because a shop would have charged about 700 to do it, , but a good quality set of bearings only cost $100. Its a Chrysler 9.25 with 3.55:1 gears. The pinion was a little smaller than that, but it was still fairly large and very heavy.
Can't wait for more fairmont videos.
Man! EricTheCarGuy, I throughly enjoy your content. This video is very helpful I just bout a 2004 grand marquis and this diff is very similar except I think mine doesn’t have traction lock
Hope you do a IFS front axle next off an F-150. Straight axles aren't much of a challenge unless you are working in the snow in your driveway! Like the idea of changing the rear drums to discs too.
thanks! I've been waiting forever for this video
I'm not sure if you've ever tried them but I just started using panther grip gloves. They are incredible. Super strong and extremely comfortable. I noticed you are wearing just the normal white ones. If you haven't tried them before they really are worth a look. I haven't ripped a glove yet.
You're a good mechanic.
I would have probably put the spare parts up for sale on ebay or craigs list...never know some might need them.....or save them for a budget build. That's just me....how ever so happy to see the fairmont build.
I also have a Mustang sitting in the garage. ;)
oh yeah the stang....forgot about it.
A little late now but I use a box end wrench to remove brake cables from the backing plate. I forgot what size worked best but with the right size it can be removed very quickly.
Eric, a tip for the brake cables. use a 1/2" or 13 mm box end wrench and slip it over the cable, driving it down over the cable retaining tangs. Found it very helpful when dealing with brake cables. use an older wrench.
Great tip, thanks!
I've used a 9/16 or 1/2 inch boxed end wrench to compress the tabs on the Parking brake cable retainer. That works quickly. Slide the wrench over the cable and it compresses the tabs.
I don't know if this was said in the comments before me or not but its actually pretty easy to make a parking brake wire removal tool. I made one for my 8.8 swap into my wrangler and it worked on both the ford and jeep parking brakes. I just took a small 12-16in piece of thin wall 3/8 inner diameter tubing if i remember correctly and tightened it in the vise so it crushed flat about half way down the tube then I ran a large easy out tool into the end of the pipe so it expanded it and gave it a taper. after that i just bent the pipe in half where the crease was from the vice and used the bottom of it as a handle so you can wiggle it back and fourth and move it around until you catch all of the keepers and pull on the cable on the other side and it should pop right out
One man can change the world! Your videos are so awesome that I decided to cancel my cable television. No more monthly payments to Time Warner, Dish Network, etc. Thank you, Eric, for a great deal of knowledge and entertainment. I’ve been working on cars for over 30 years, but I learn something from every one of your videos. The fact that you never rush, and that you always explain both the theory and the functioning of the parts thoroughly, really sets you apart.
always the best videos eric!! thanks
Thanks , for the great video schooling.
Another very informative video, thanks
Perfect set of vids for me to rebuild my ford explorer 8.8.
Question please.
What is the cause of excessive axle end play. One side is a solid 3/16 inch the other is at least 5/16.
Thanks in advance.
That was very informative thanks 👍
good video and very easy to understand,thanks!
Ive been there and had to reuse the crush sleeve too . put an old long socket or pipe the right size and work your way around with a hammer. Its not good practice to do this, but when suppliers don't you just have too on occasion.