Fanatec DD Extreme stuck in bootloader mode when turned on.
HTML-код
- Опубликовано: 20 окт 2024
- Fanatec Driver version 455
Base firmware: 2.0.1.4
Wheel firmware: 1.0.3.0
8-09 Update: I HAVE THE EXACT SAME PROBLEM AGAIN!!!! :(
I was able to use the wheel base about 5 times and now it's fucked again....
3-09 Update: Just received my DD Extreme back from Fanatec. They replaced the main PCB in the DD Plus base. All is working great again!
It less than 2 weeks to get it back after sending it in for repairs. Kudos for the fast repairs.
27-8 update: Finally received an RMA from Fanatec support last week. I sent it to Fanatec the same day.
Track&trace showed they received it yesterday.
I hope it won't take too long to get it repaired or replaced.
succes met wachten op een reactie van Fanatec support.. Kan wel een tijdje duren is mijn ervaring
Hello! I noticed that when you have PC Mode (Red) and the update is downloaded, it automatically switches to PlayStation Mode (Blue), which causes the update to stop. Try to do this: turn on the steering wheel when it starts PC Mode (Red) as in the video: plug in, update when you switch to PlayStation Mode (Blue) disconnect the cable from the PC, switch to PC Mode (Red) and then turn off the steering wheel. Turn it back on and plug it in under your PC, update it and it should work.
@Mako19298 It switches to blue after it completes flashing the base firmware. At which point I can use it on my PS5.
I have to do this every time I want to use the wheel.
People are just having lots of problems with this wheel base. They clearly have rushed the product through and design flaws are present
I had similar problem with my CSL DD, i need to remove clamp which is holding qr1 with usb-c, push qr1(base side) in, screw clamp (hx5 mm if i remember correct) and up to now base works just fine
@@krzysztofczerwinski3230 The QR2 is mounted differently on the DD+.
I have exactly the same problem with my DD+ base. I have an RMA but I'm not sure I should send it to Fanatec in their current state. Right now I have a base that works after updating it. If I send it in I may never get it back.
@MisterPokeylope If I get to send mine in, I will. I have full warranty. Worst case scenario, I drive to Landschut, Germany to get a new DD+ base.
@@lagarde72 I've decided to send mine in.
@@MisterPokeylope Did you send in the whole package, or only the base?
I bought the base separately, not as a bundle.
@MisterPokeylope Finally got an RMA today. I just sent it out.
Hopefully it's not going to take months to get it fixed and shipped back to me.
I had the same issue with DD + …. I reverted to driver 454 and old firmware then upgraded to 455 driver but do not update the latest firmware . Try it , it’s exactly what happened to me
@LENNY127 I will try it. But so far, when I have it working and I turn it off, it will only go to firmware update mode when I turn it on again.
@LENNY127 Unfortunately it didn't work for me.
How did you get on with your warranty ticket ?
@@GavM1510 Still waiting for a solution.
@lagarde72 what a shitty company.
just remove the usb from ps5 and replug it, mine just continues to calibrate when pluged out of ps5 and continues as normal, But yeah, same issue.
@@zenflight2450 Mine does nothing when unplugging the usb cable. It remains in firmware update mode.
I had the same issue with downgrading the firmware, but the update didnt reconnect my base too, the only thing that worked out for me was hitting driver repair (troubleshooting) untill it succeed the update proppely en succesfully would reconnect to my pc, in my opinion updating the latest driver and firmware available was my only way out, to provent damaging by any chance, and allways update every firmware manual separately
Try to use another pc. I had same problem with my dd pro, using another laptop helped me
@@AN0THER_GUY I tried another pc. Same result.
Fanatec is trash !!!! Switched dd1 for the simucube ! We spend to much money to be treated how we are from them ! Zero response’s help or action