Hey Nathan - out of all the videos I have been through, yours was the first straight forward guide to getting my 2960 on the network and attached to the internet - I did have to #no shut on WLAN 1 to get it going... nice job!
@@NM_Tech do you have other videos coming...? I'm not a network guy, not am I going for any Certs... Just a hobbyist trying to expand my Network (Computers and Servers)
In case you haven’t already checked my channel, I also do videos over Voice over IP(VoIP) phones and phone systems as well. Even after this video was made. That seems to be the subject in which the next video I publish will be over.
I was just given this switch board from the company I work for sense it's outdated and I'm trying to get my Network+. This will help a lot with demonstrating my understanding of how servers are built and configured. Thank you!
Tip for anyone having issues getting the COM port to popup under Devices (Windows 10). The rollover cable I got didn't automatically install the driver for the cable at least for me. You may need to manually install it but I would check the Windows update section first and see if you have the option to install the driver from there. I was a bit confused for a while I ended up plugging the cable into a Linux box I have and everything worked. I just got the network switch and roll-over cable so had to pinpoint the cause of the issue.
Hey just an FYI your enable secret (password) is already encrypted and is a stronger encryption then service password-encryption. Service password-encryption encrypts all passwords that are in plain text. Enable password command would be plain text, enable secret, is already tell you it will be encrypted. So far good video
Thanks. This was great, I just bought a C2950-48 port switch and this helped with doing some initial configuration. I need to update my iOS next, I also couldn't try the Gen RSA keys or set ssh up yet. Waiting for a C1841 router next week and a C3560 switch and I'll be on my way to starting my CCNA training.
Nathan - thank you so much for this. Way better than some of the lectures I've had from some of my professors! I hope to see more videos from you since I just hit the subscribe button! Thanks again!
Getting one too for cheap but not familiar with Cisco switches. I do have a question and you may have a video on it..if for instance you want to export the config file how would you do that and then import it - just in case something happens you can load into another similar switch of Cisco
I believe you would need to issue the "show run" command in privileged exec mode on the current switch, copy the running config by literally highlighting all of it with the mouse, then paste all that to some .txt file and save that to your computer. Then when you boot up the new switch, copy all the contents of that .txt file you saved, enter global config mode on the new switch, then paste all of those contents in the terminal emulator window. I THINK that's how you do it if I'm not mistaken.
@@NM_Tech thanks Nathan is their a command that will actually show it all ..usually I have seen the --MORE-- then I think you hit the space bar. I'm just wanting to see it all then highlight and copy..I hope I made sense here
@@rhdtv2002 hey my friend you can either tftp the configuration file with copy or just copy to USB if you have that option. USB is easier but tftp isn't hard.
Copy running-config | redirect flash:backup.cfg Configure replace flash:backup.cfg To replace the config. Term width 0 Term length 0 This will disable width to 0 and the length 0 will disable auto more
I just got one of these switches from work to tinker about on but when i open a putty session, it just has the green bar and when i press enter, nothing happens. Would you know why?
@@NM_Tech Serial and i'm setting it to COM4. I've looked into it and i think i can't see USB Device (COM4) under ports in device manager. I just wondered if there was something else as i was still managing to open a Putty session
You need to find where your USB device is in device manager and use whatever port it is. Maybe try unplugging your usb device and check device manager and see if there is something missing. Then plug it back in and if whatever was missing reappears then you know that’s the device and you need to use that port.
@@NM_Tech Yeah i've checked in device manager and it does say COM4 and when i click on it, it says USB to serial converter but Putty is still not doing anything when i press enter or any key for that matter :/
Only if your switch has no DHCP support and you want to set VLANs on different networks, other than that you just need to add VLAN networks to route table and route each network to right gateway.
Great video..but it's difficult to me to see the text bcz its too small ..can u please increase ur font text size for other videos..it will be good to watch.
Hi there, Great Vid. I'm just wondering if you can help me out by giving some pointers. I ended up buying the router you got which is almost the same mode - WS-C2960S-24PS-L. My question is, can you hook up your router using the SFP port to this switch that serves as uplink/downlink instead of using one of the 24 ports in the switch? My plan is to get rid of my ISP fiber modem and replace with GPON router that comes with 4 LAN ports. I noticed my switch have 4 SFP ports and wondering if I can hook them all to my router using SFP transceiver. What do you think? Thanks.
Update: I found it, it's just cisco! I purchased a similar switch but without the Gb ports from amazon just for practicing purpose when I pressed the mode button for 3 seconds I got all the LEDs solid green which suppose to mean it wasn't configured before however when I try to access the privilege exec mode it asking for password, is there a default password I can use? I checked the manual and it says that there should be none at initial config
Hey Nathan - out of all the videos I have been through, yours was the first straight forward guide to getting my 2960 on the network and attached to the internet - I did have to #no shut on WLAN 1 to get it going... nice job!
Thank you! I’m glad the video helped!
@@NM_Tech do you have other videos coming...? I'm not a network guy, not am I going for any Certs... Just a hobbyist trying to expand my Network (Computers and Servers)
In case you haven’t already checked my channel, I also do videos over Voice over IP(VoIP) phones and phone systems as well. Even after this video was made. That seems to be the subject in which the next video I publish will be over.
I think video font bit higher unable to see through mobile also port configuration need to add and save at boot
@@NM_Tech great video! Did you connect the switch to your Home ISP router or to a Cisco Router?
I was just given this switch board from the company I work for sense it's outdated and I'm trying to get my Network+. This will help a lot with demonstrating my understanding of how servers are built and configured. Thank you!
Glad to have helped.
nice dude. I got a 48 port switch myself recently so gonna get it hooked up soon with this. kudos bro
Tip for anyone having issues getting the COM port to popup under Devices (Windows 10). The rollover cable I got didn't automatically install the driver for the cable at least for me. You may need to manually install it but I would check the Windows update section first and see if you have the option to install the driver from there. I was a bit confused for a while I ended up plugging the cable into a Linux box I have and everything worked. I just got the network switch and roll-over cable so had to pinpoint the cause of the issue.
Thank you. that comment saved me some time.
Thank you for such a lovely video. I was able to access and configure the Cisco switch using the steps outlined in the video.
Glad to have helped.
Hey just an FYI your enable secret (password) is already encrypted and is a stronger encryption then service password-encryption. Service password-encryption encrypts all passwords that are in plain text. Enable password command would be plain text, enable secret, is already tell you it will be encrypted. So far good video
Thanks. This was great, I just bought a C2950-48 port switch and this helped with doing some initial configuration. I need to update my iOS next, I also couldn't try the Gen RSA keys or set ssh up yet. Waiting for a C1841 router next week and a C3560 switch and I'll be on my way to starting my CCNA training.
Nathan - thank you so much for this. Way better than some of the lectures I've had from some of my professors! I hope to see more videos from you since I just hit the subscribe button! Thanks again!
packettracer is very bad i feel you
I'm learning for my CCNA and this was just Awesome man. Thanks
ca you tell me what kind of knowldge i need to have to pass CCNA test ?
thx man, very instructive. It helps a lot with the CCNA
I opened RUclips and my dad has been looking at this
I have a 48 port but how do i find out what com to use?
Are you talking about the console port?
Nathan Morgan no ok so as i enter the putty program i tried doing serial but i dont know which com to use like you used com4 correct?
Yes I used com4. Are you using a rollover cable?
Nathan Morgan currently i am not do i have to purchase one in order for this process to work?
What cable have you been trying to use to do this?
Getting one too for cheap but not familiar with Cisco switches. I do have a question and you may have a video on it..if for instance you want to export the config file how would you do that and then import it - just in case something happens you can load into another similar switch of Cisco
I believe you would need to issue the "show run" command in privileged exec mode on the current switch, copy the running config by literally highlighting all of it with the mouse, then paste all that to some .txt file and save that to your computer. Then when you boot up the new switch, copy all the contents of that .txt file you saved, enter global config mode on the new switch, then paste all of those contents in the terminal emulator window. I THINK that's how you do it if I'm not mistaken.
@@NM_Tech thanks Nathan is their a command that will actually show it all ..usually I have seen the --MORE-- then I think you hit the space bar. I'm just wanting to see it all then highlight and copy..I hope I made sense here
Unfortunately not.
@@rhdtv2002 hey my friend you can either tftp the configuration file with copy or just copy to USB if you have that option. USB is easier but tftp isn't hard.
Copy running-config | redirect flash:backup.cfg
Configure replace flash:backup.cfg
To replace the config.
Term width 0
Term length 0
This will disable width to 0 and the length 0 will disable auto more
I have tried doing the RSA generation key but whenever I do "do show run" the key doesn't show and when I do "sh ip ssh"
Hey man are you able to provide a link to buy that bracket? I've been having a hard time finding brackets .
I just got one of these switches from work to tinker about on but when i open a putty session, it just has the green bar and when i press enter, nothing happens. Would you know why?
It looks like it’s not establishing a connection to the switch. Are you trying to ssh it or use serial?
@@NM_Tech Serial and i'm setting it to COM4. I've looked into it and i think i can't see USB Device (COM4) under ports in device manager. I just wondered if there was something else as i was still managing to open a Putty session
You need to find where your USB device is in device manager and use whatever port it is. Maybe try unplugging your usb device and check device manager and see if there is something missing. Then plug it back in and if whatever was missing reappears then you know that’s the device and you need to use that port.
@@NM_Tech Yeah i've checked in device manager and it does say COM4 and when i click on it, it says USB to serial converter but Putty is still not doing anything when i press enter or any key for that matter :/
Would you like to join my discord to get into more details on troubleshooting?
Wouldn’t it be line vty 0 15 for a switch?
not necessarily...it could be vty 0 4
This helps a lot. Can you please explain on which assumption you chose the IP address and MASK?
Does it matter where i plug in from my router to the switch? Can i use any port or is there a specific one i should use?
Doesn’t matter
Only if your switch has no DHCP support and you want to set VLANs on different networks, other than that you just need to add VLAN networks to route table and route each network to right gateway.
Great video..but it's difficult to me to see the text bcz its too small ..can u please increase ur font text size for other videos..it will be good to watch.
thanks for this informative video. just the last few configurations were a little confusing
Hi there, Great Vid. I'm just wondering if you can help me out by giving some pointers. I ended up buying the router you got which is almost the same mode - WS-C2960S-24PS-L. My question is, can you hook up your router using the SFP port to this switch that serves as uplink/downlink instead of using one of the 24 ports in the switch? My plan is to get rid of my ISP fiber modem and replace with GPON router that comes with 4 LAN ports. I noticed my switch have 4 SFP ports and wondering if I can hook them all to my router using SFP transceiver. What do you think? Thanks.
Update: I found it, it's just cisco!
I purchased a similar switch but without the Gb ports from amazon just for practicing purpose when I pressed the mode button for 3 seconds I got all the LEDs solid green which suppose to mean it wasn't configured before however when I try to access the privilege exec mode it asking for password, is there a default password I can use? I checked the manual and it says that there should be none at initial config
Try cisco as password (most Cisco devices default password is cisco), if it doesn't work, then you need to reset the switch to factory defaults
Can this only be done with a rollover cable?
I use the mini usb on the switch
Hey, how do I can open port for different device? When I don't know password and user name ?
Sir can 2e configure catalyst2950 series switch with lan cable
after giving this an ip address, can you then access a GUI page for configuration?
No. This model switch only has IOS. Only the recent models have GUIs
Thanks a lot boss. Great video! i have learnt a lot.
Great video! Thanks for the help.
Bro do vlan configuration video
You are nice speaker bro.
I have one of these and some others for sale.
This isn’t a place to self advertise.
Video is not zoom in
Great job
👍👍👍
Glad you enjoyed.
you no what! your not configuring it total
Every fibre in my being is screaming use a blue cable.
you aint even A+ Certified tho
Are you A+ certified?
@@NM_Tech hey what is the purpose of this? Can I use this switch as a router for miners? Any ideas
This is a network switch. Not a router
#poundsign !hashtag