Complete House Washing - Start to Finish (Raw Footage)

Поделиться
HTML-код
  • Опубликовано: 4 дек 2024

Комментарии • 25

  • @steppspressurewashing
    @steppspressurewashing  18 дней назад

    It's a long Video, and a quick wash to start my day. Y'all be safe out there!

  • @jerrymeyers2075
    @jerrymeyers2075 18 дней назад +1

    Always use Elemonator especially on chilly days helps hold the chem to the house. When it's colder I also run a 1.8 injector. Switching to a new softwash system hopefully over the weekend and I'll send you a video when completed.

    • @steppspressurewashing
      @steppspressurewashing  18 дней назад

      @@jerrymeyers2075 nice!! What Ratio do you pull with the 1.8? I look forward to seeing what your new setup is!!

  • @GrimeBustersofPender
    @GrimeBustersofPender 18 дней назад +2

    Liked the longer format! I am also in NC (Wilmington area). Do you continue washing until temps drop? Winterize your machine or do you usually keep in the garage?

    • @steppspressurewashing
      @steppspressurewashing  18 дней назад +1

      Thanks, I'm glad you enjoyed it!! I wash year round, but not below freezing. I have never winterized the pump, because I keep it in the garage where it can stay above freezing. Having winter gear helps a lot.. I didn't have proper gear my 1st winter, and it was brutal. You have to stay dry lol!!

    • @TheGoodfella7272
      @TheGoodfella7272 17 дней назад +1

      Agreed! Love the longer format! So relaxing and satisfying. Keep it up!

    • @steppspressurewashing
      @steppspressurewashing  17 дней назад +1

      Thanks for watching!! I'm glad you enjoyed the longer video! 😁

  • @twill8210
    @twill8210 16 дней назад

    Watched to the very end. Thank you for sharing I’m wanting to start soft washing in az so it’s really helpful

    • @steppspressurewashing
      @steppspressurewashing  16 дней назад +1

      @@twill8210 I'm glad you enjoyed it!! Are you planning on a spring launch?

    • @twill8210
      @twill8210 16 дней назад

      @ yes. Most homes here are stucco. Any recommendations on sh percentage %. Also. I’ve stil yet seen pricing videos on average cost. Do you charge based on sqft ?

    • @steppspressurewashing
      @steppspressurewashing  16 дней назад +1

      If i remember correctly stucco is around 2%, but I've never done stucco... Here's a video I made on how I set my pricing. ruclips.net/video/Fc3nfjSXgYY/видео.html

    • @twill8210
      @twill8210 16 дней назад

      @ thank you much. Keep up the good work. Love the videos

  • @SP-mg3li
    @SP-mg3li 17 дней назад +1

    @steppspressurewashing, I would paint those boards on your trailer so it will last longer... (I'd use a bed liner... That's what we did with our enclosed trailer... Used Herculiner)

    • @steppspressurewashing
      @steppspressurewashing  17 дней назад +1

      Thanks for the tip! I actually put a few coatings of a secret family recipe for oiling wood... Herculiner might be better though!

    • @SP-mg3li
      @SP-mg3li 17 дней назад +1

      @steppspressurewashing We gave ours a light sanding to remove the shine and knocked off the dust then applied the Herculiner.

    • @steppspressurewashing
      @steppspressurewashing  17 дней назад +1

      @@SP-mg3li nice!! I'm a big fan of wood preservation, and I love the oil because I can add a little. Or a lot depending on how I feel. Also it's really cheap lol!!

  • @SP-mg3li
    @SP-mg3li 17 дней назад

    @steppspressurewashing You should get either a tripod screen or a go pro so you don't have to hold your phone.

    • @steppspressurewashing
      @steppspressurewashing  17 дней назад +1

      Yep, I'm planning on doing some time lapses with my tripod soon! I have a go pro, but haven t used in in almost 2 years... I will need to dig it out for some new vids!!

  • @heibelmedina2301
    @heibelmedina2301 15 дней назад +1

    What do you do for water reclamation? Does it matter in your state/county

  • @chrisa2024
    @chrisa2024 18 дней назад +1

    Quick question did you buy a 3 way JRod or did you cut a 4 way? Could t find a 3way

    • @steppspressurewashing
      @steppspressurewashing  18 дней назад +1

      Amazon used to sell the 3 way j rod holder, but now the link wont work.. I actually broke my 4 nozzle by putting too much force on it... It was supposed to have a shooter tip as well... The 3 way has been perfect though! You could probably just cut the weld on a 4 to make it a 3

  • @IFix-Things
    @IFix-Things 18 дней назад +1

    Where did you get your jacket? Is it SH resistant?

    • @steppspressurewashing
      @steppspressurewashing  18 дней назад

      Here's a video I made about my uniform with links for everything ruclips.net/video/m1lKS2C56g4/видео.html
      The jacket is from queensbro, and it is SH resistant 👍