Hey bro, great vídeo and awesome mask!! I'm from Brazil and i'm trying to do the same as you did, but i have a problem. The link of the file don't give the exact mask size. Wich size did you put to print yours? Thank you for your attention!
Ok, this is amazing!! Here in my city there is a 3D printing "store", do I have to give them my exact measurements or does the mask have to be a little bigger than my face? They asked for my measurements :)
Well the size on the program Cura is 400% and it should fit most. So unless they use a different program for the slicing then measurement would be good too. O tho just a size increase is all thats needed.
Hay man like your video, really looking forward to your next video and would like a 3D print of a Dickbutt and some usefull ways i could use it on my day to day basis. And if you can film your self getting the matirials from homedepot or other places I would apreciated. Ps. If you ask why i want you to film your self getting the matirials is cause i would like to see it so i know where it is and stop slaking
Hi! I have an Ender 3 V2, what size would I print at? At first, I tried 380% and while I didn't even print half of the mask, it looked like it wasn't going to fit. So, then I tried 400% which is what you have in the description. But it still looks a bit small. It's not done printing yet. Do you think I should make it bigger?
At those sizes it still should be able to print on an ender 3. Not all sizes work the same on the slicer tho. These % work on cura and meshmixer. You can also measure it using an already sized mask or helmet or take your heads measurements and scale it to it on tinkercad.
You can do it in meshmixer or tinkercad. I used meshmixer, click edit, plane-cut. Then just undo and flip. There are a couple of good tutorials on it as well.
@@GrayFox120 you can use Meshmixer, its simple to use, import the file, edit, plane cut. Then just save, undo and repeat. There are also plenty of good tutorials on YT as well.
For the tarp i got some nylon fabric at the local store and cut it in the shape using a refrence picture. Then for the hood i used a sewing machine to stitch it all together. There are good patterns online for these shapes. Then red acrylic paint. For blood, darken the red with some black.
I've been at this forever... Cura say's the knife is too thin to print, on it's spine. I tried it flat, and the last inch-ish is about 1 later thick. Trying my best to work with this in Tinkercad, but, not having any luck. :(
Well, atleast how I did it was laying it down with its sharp angel facing up from corner to corner at 2150% scale, 10% infill, layer height 0.2, wall thickness 1.0 and wall line count 2. if you want to reshape it you can try meshmixer. Its my go-to for tinkering with files.
@@sashas1ash Thanks, I've been trying for a few hours to no avail. I cut the blade and handle, into 2 parts, so they PEG together. Maxed out my bed with the blade, and Cura still says it's too thin. I tried printing it on it's side a few different ways, with no luck. I'm still working on it. I may try it on it's spine, even though Cura tells me know. Maybe it's lying. Lol
Yes, definitely. Make sure your supports are stable for the full mask. If you're gonna sand and paint I recommend atleast prime and wet sand before painting. Just to get any imperfections out.
@Bruh • 10y ago and I scaled it to 400% I found that it's a nice size that fits most. It also helps to compare to other helmets or masks that are up to scale already or printed before.
@Alfg55 wow that shouldn't be 30 hours lmao. Try changing the infill or the travel speed or supports. I have it at a 10% infill with 50 speed and 60 for supports. Yes when I open it on cura I have to increase the size to 400% so it fits. You can play around with the size to fit your needs too.
I had a problem with my print the bottom half came out absolutely perfect but the top half did not do you have any socials I can add you on to send you pictures I could use the help lol
I dont really have a pattern per say. I just used a refrence from google and traced it on to nylon. I added the image i used to the description just in case. 👍
@@itzjustsoda9496 PETG is also a good option. Also PLA+ if you want it a bit more durable. I used PLA cause its what I had at the moment. But it worked really well.
Hello! I was going to send a private message but it appears you cant do that on here anymore. I was going to ask, do you, or would you, sell a finished mask? I dont have a 3D printer and dont intend to get one. This looks more accurate to Dead by Daylight than the Official ones. Or would you be interested in a trade? I'm a artist/mask maker and just got done sculpting a Devil Face mini bust that Im going to release sell a small batch of. Either way, let me know!
This is great. The mask, the comedy, your personality, everything. You earned a sub.
Loved this video, loved the mask, and you made me roll over laughing. You sir have my subscription
Thats really cool watch out fun world
This mask is spectacular I wish I had one for Halloween
Options: Use a 3D Pen to fill that inside line. Can also paint the inside with EPOXY/RESIN, for strength. Epic video. Love your personality.
Hey Slash you should totally make a 3D print of the wassap mask!
Hahah oh definitely!
Noice I liked how it turned out
Just Awesome, good Job man👍🏻
I really want to get the official costume and the one in-game. It's a cool look.
I got so excited when they announced official costumes form the games!
The mask looks awesome :)
Hey you Great video I hope that Ghostface mask could be in different color and symbols just without the devil horns
Nice job. Please make more types of ghost face mask
Yeah with different color and symbols
Holy shit this is so well made, as a student I can’t really have a 3D printer sadly.
Would pay a lot if costumes like these were available
nice
The knife that GHOSTFACE used is called “Buck 120” of U still tryna buy it
Subscribing. Very goofy and charismatic in the best of ways and of course very informative:D
This is amazing
Do the original white one
you desurve alot more subscribers
I love it I want one!
This is amazing omg
Well done! Try the Ghostface Viper mask, please!
Hey bro, great vídeo and awesome mask!! I'm from Brazil and i'm trying to do the same as you did, but i have a problem. The link of the file don't give the exact mask size. Wich size did you put to print yours? Thank you for your attention!
Thank you ma dude! I used 380% size increased on Cura
Ok, this is amazing!! Here in my city there is a 3D printing "store", do I have to give them my exact measurements or does the mask have to be a little bigger than my face? They asked for my measurements :)
Well the size on the program Cura is 400% and it should fit most. So unless they use a different program for the slicing then measurement would be good too. O tho just a size increase is all thats needed.
@@sashas1ash Thank u so much!! I'm so excited >.
Nice costume do the viper cosplay mask and suit
Exelent. Just excelent.
Hay man like your video, really looking forward to your next video and would like a 3D print of a Dickbutt and some usefull ways i could use it on my day to day basis. And if you can film your self getting the matirials from homedepot or other places I would apreciated.
Ps. If you ask why i want you to film your self getting the matirials is cause i would like to see it so i know where it is and stop slaking
Bruh
I’m trying to print out a lithophane scream mask from scream 4 and mold it to make it softer for slicone cast
That's awesome dude!
That's awesome!!! Too bad the knife file is gone :(
Hi! I have an Ender 3 V2, what size would I print at? At first, I tried 380% and while I didn't even print half of the mask, it looked like it wasn't going to fit. So, then I tried 400% which is what you have in the description. But it still looks a bit small. It's not done printing yet. Do you think I should make it bigger?
At those sizes it still should be able to print on an ender 3. Not all sizes work the same on the slicer tho. These % work on cura and meshmixer. You can also measure it using an already sized mask or helmet or take your heads measurements and scale it to it on tinkercad.
How much would it cost me to get one of these or am entire outfit comissioned
How did you divide the STL file into two? 3D-Printing beginner here
You can do it in meshmixer or tinkercad. I used meshmixer, click edit, plane-cut. Then just undo and flip. There are a couple of good tutorials on it as well.
@@sashas1ash if my 3d printer is too small, do you know what tool can I use to separate it into 4?
@@GrayFox120 you can use Meshmixer, its simple to use, import the file, edit, plane cut. Then just save, undo and repeat. There are also plenty of good tutorials on YT as well.
@@sashas1ash Last question SashaSlash, how did you make the cowl with cloth? did you just superglued the edges or saw it in?
@@GrayFox120 I sewed two halfs together and then glued the extra edges to the mask
Do the smile one of of scary movie
Hey nice video, I was wondering what 3d printer are you using in this video, And how long did it take to print?
Im using a CR-10s, the top part took 10 hours and the bottom took 7 hours. Both using 15%infill
@@sashas1ash thanks bro
Do you possibly have a link to the 3d printer?
@@yummysandwich3421 creality3d.shop/collections/cr-series/products/creality-cr-10s-diy-desktop-3d-printer-300x300x400mm
Thanks again
how to cut this mask and print it? as in the video? (in cura)
You can use Meshmixer, tinkercad or blender. I used meshmixer for this one.
Thanks @babajork
How did you make the tarp?
For the tarp i got some nylon fabric at the local store and cut it in the shape using a refrence picture. Then for the hood i used a sewing machine to stitch it all together. There are good patterns online for these shapes. Then red acrylic paint. For blood, darken the red with some black.
I've been at this forever... Cura say's the knife is too thin to print, on it's spine. I tried it flat, and the last inch-ish is about 1 later thick. Trying my best to work with this in Tinkercad, but, not having any luck. :(
Well, atleast how I did it was laying it down with its sharp angel facing up from corner to corner at 2150% scale, 10% infill, layer height 0.2, wall thickness 1.0 and wall line count 2. if you want to reshape it you can try meshmixer. Its my go-to for tinkering with files.
@@sashas1ash Thanks, I've been trying for a few hours to no avail. I cut the blade and handle, into 2 parts, so they PEG together. Maxed out my bed with the blade, and Cura still says it's too thin. I tried printing it on it's side a few different ways, with no luck. I'm still working on it. I may try it on it's spine, even though Cura tells me know. Maybe it's lying. Lol
6:04 when you lose your ruin at the start of the match
Sup! I have a CR-10 Large FDM will i be able to print the full mask.. and if i can .. can i just sand it and spray paint it.? Thx!
Yes, definitely. Make sure your supports are stable for the full mask. If you're gonna sand and paint I recommend atleast prime and wet sand before painting. Just to get any imperfections out.
Thx, also what size do i use for the mask.. im using cura.
@Bruh • 10y ago and I scaled it to 400% I found that it's a nice size that fits most. It also helps to compare to other helmets or masks that are up to scale already or printed before.
Do you think I would be able to spray paint the Walmart fun world mask ?
Painting a rubber mask with spray paint might stay sticky or crack when it moves. You could try light sprays. Or airbrush, Something superficial.
how long did this take to print for the top half?
It took roughly around 11 hours
@Alfg55 wow that shouldn't be 30 hours lmao. Try changing the infill or the travel speed or supports. I have it at a 10% infill with 50 speed and 60 for supports. Yes when I open it on cura I have to increase the size to 400% so it fits. You can play around with the size to fit your needs too.
@Alfg55 I used grid pattern and for the support speed is in the speed tab. If you cant see it go to settings and configure setting visibility
I wish I had a 3D printer
You could save up a bit, cheap good ones are 150 like the ender 3, and that's without sales 😉.
Hello I was wondering if I can get a link to the file for the knife please?
Jesus how many hours you spent doing this?
Took around 2 weeks to fully make the cosplay.
I'm thinking of getting into 3D printing would you recommend your 3D printer?
Yes, both the CR-10 and the Ender models are great printers!
I had a problem with my print the bottom half came out absolutely perfect but the top half did not do you have any socials I can add you on to send you pictures I could use the help lol
My IG Babajork lets see if we can fix it lol
Where did you get the cloak?
Hello fellow Ghostie, do you have the files to 3D print the knife? I'd be truly truly grateful if you could send them
Hi would you be able to share the pattern for the cloak/poncho?
I dont really have a pattern per say. I just used a refrence from google and traced it on to nylon. I added the image i used to the description just in case. 👍
@@sashas1ash oh okay thank you appericate it!
can you link the knife as well
Do you sell these?
What filiment are you using?
I use PLA
@@sashas1ash Thanks for the quick reply. But I’m a bit confused. Wouldn’t using something like PETG work better?
@@itzjustsoda9496 PETG is also a good option. Also PLA+ if you want it a bit more durable. I used PLA cause its what I had at the moment. But it worked really well.
Guide for ghost face 5:40 all u need to know
Hello! I was going to send a private message but it appears you cant do that on here anymore. I was going to ask, do you, or would you, sell a finished mask? I dont have a 3D printer and dont intend to get one. This looks more accurate to Dead by Daylight than the Official ones. Or would you be interested in a trade? I'm a artist/mask maker and just got done sculpting a Devil Face mini bust that Im going to release sell a small batch of. Either way, let me know!
Hello! Do you have an Instagram so i can message you privately?
@@sashas1ash Yes, LastKnownFX.
Where’s the blueprints?
The 3D files are in the description.
@@sashas1ash thanks!
You do realize fun world sells these right?
Yes