Being I knew nothing about this, I cleaned up the 2 connection points with 00 steel wool (make sure you leave no strings) reconnected and voila ! Had a gas gage again. Makes me feel much better. Thanks for the vid!
Great video. I would caution anyone doing this to not use power tools when unscrewing the sender....huge fire hazard. Fuel vapors can ignite from the sparks on the drill bushing.
People don't realize how volatile gasoline vapor is. That's the reason you use diesel or kerosene to light brush piles and the like. They are not as flammable. In fact fairly hard to ignite. You see idiots blow themselves up or get severely burned when they use gasoline to start fires.
you measured incorrectly for your tank it should have been 7 13/16 or 198mm. not 7 3/16. also you forgot to mention the 5/16 less than proper arm length which is what gives you the emergency gas when gauge reads empty. but a fair video anyway.
Thanks for this video,helped me install my sending unit perfectly.I think you should make another video ,detailed in the wiring the sender to the gauge and to ignition etc,thats where I'm lost,I suck at anything electrical,there's no good videos on this,you could do a good job,at it.
Something that I haven't seen covered is that older cars may have a copper float which can leak. If it fills with fuel it will sink and always read empty.
Are all the holes the same?? Mine just broken the wire off in the tank. It also seemed that my gauge was off by a half tank. I did touch the wire back to the point and my gauge did move. I which is the longest lasting gauge available. I know fuel is everyone's best friend
your videos are really helpful. thanks. when i winterized my boat last year, i used the antifreeze and ran it through the entire system like you showed in your video. my boat started up on the first shot this spring. my question is, when i ran the boat with the ear muffs with the water, i noticed an oily chemical mixed in with the water coming from the exhaust. is that the residual antifreeze that was in the system. thanks. the boat ran great on the lake. its a 97 bayliner capri classic 2050. merc,350
When I turn the key, the fuel gauge shows full, when I turn the ignition off, it shows empty. Tested sensor with measuring instrument it has the correct Ohm value. It is both a wema and a wema instrument. Has worked before and also not replaced anything previously. When I disconnect the sensor's 2 cables it still shows full. what do you think is wrong then?
I'm going to try this today. Is it OK to leave that much (looks about 1/4") of play on float between stoppers? Why would you want it to slide back and forth?
I need help with mine well you see the thing that you replace well I don’t think mine is working because I took both original tanks out and my dad bot me a new aluminum tank for the bed and it had that float think like your’s but this new tank of mine has ouly one wire plug on it and yours was 2 but my old tanks had 3 wires plugged into it so witch wires do I use for this new tank I have 3 opinions a red a black and the blue wire has power so I tried hooking up all 3 with no response but blue wire with power makes the fuel gage go up to full no matter if the float is up or down I need so help
@@BigIslandMNMinnetonka What you have effectively done is provide yourself with some "emergency" gas. Your gauge will read empty but you'll still have 5/8" of gas left in your tank. I like it. :-) Great video.
Hi my tank is leaking gasoline from where the tap where where the part at , how can I fix the leak it’s just a little bit but I don’t wanna use like that
I'd add that many many times with boat electronics the problem is nothing more than a bad connection due to corrosion, before you bought a new sender you should have removed the old one, cleaned the connections, checked the wiper are to make sure it was in contact with the resistive wire then lifted and lowered the float with the key on and see if it starts working. Most times it does, other than a bad connection or mechanical damage the only thing that goes wrong that isn't easy to fix is the float might sink.
@@BigIslandMNMinnetonka unfortunately after a long paddle to the shore whilst avoiding a barge or two I had plenty of time to troubleshoot the issue while I waited for my buddy to go get a jug of fuel....
Measure twice, cut once.... the book said 7-13/16 and you cut it 7-3/16... your tank was just over half full, and your gauge is reading 3/4 full.. that 1/2 inch you fucked up on is throwing your gauge off.. but its close.. and it will work...
Thank you but - it was 7 and 13/16 not 7 and 3/16, One half inch of swing cut off the sender. Will probably make readings at full and empty a little off, measure 2x cut once.
I am finding that not all fuel gauges are the same and you need to match a sending unit with the gauge. With a broken sending unit how do you know which one to buy to match your dash gauge OHMS RANGE?
It's supposed to, the boat is moving. Cars would do that too, but they're digital and have circuitry delays built in so that they don't move around every time you take a turn.
I put mine and the gasket didn’t seal right..... gas pours out no matter how tight or loose I tighten the sender. It never leaked with the old unit on... Any suggestions on what type of sealant I can use that the gas won’t eat up????
I cut mine short! Is it screwed? My tank is 12” deep and I measured the arm to make sure it could reach the bottom and top having 12” of travel. But I cut it to like 6” (6” up and 6” down) I should be fine right?
Big Island MN yea that was my logic. I would rather play it on the safe side and show empty earlier than not. I only have about 1” of gas left out of my 12” deep tank. So it’s not wrong I’m pretty empty. Like you said I’ll just have to find out on my next full up.
You aren't testing you're replacing. Surely you test before you buy anew one. If the new sender still gives the same as the old one you've just wasted money
I know it's been said a million times, but the efficiency of this video is absolutely amazing
Thank you.
sometimes its shocking how simple repairs can be. Thank you for showing us
One of the best no-nonsense videos with tips and tricks. Thank you.
Great video. Thanks for getting to the point quickly. Too many videos on youtube are 6-10 minutes to explain 10 steps.
Glad it it saves you time. That is my goal. And I agree about videos being to long.
Agreed
Josh MADISON and Brandon LANTZ
Being I knew nothing about this, I cleaned up the 2 connection points with 00 steel wool (make sure you leave no strings) reconnected and voila ! Had a gas gage again. Makes me feel much better. Thanks for the vid!
Nice work!
No BS in this vid. Straight to the point. Wish I could give it 2 thumbs up!
Thank you so much. That means a lot
I learnt something quick before I had the chance to skip the video. Thanks bro.
Short and to the point. Best how to video. Thanks
Great design of your video sequence. It's clear and complete without wasting time. Thanks.
This guy does not suck and I pray that the virus does not find him.
Thank you. I also hope the virus doesn't find me
Your video is going to make me a hero to my girlfriend, thank you ahead of time sir!
Great video. I would caution anyone doing this to not use power tools when unscrewing the sender....huge fire hazard. Fuel vapors can ignite from the sparks on the drill bushing.
People don't realize how volatile gasoline vapor is. That's the reason you use diesel or kerosene to light brush piles and the like. They are not as flammable. In fact fairly hard to ignite. You see idiots blow themselves up or get severely burned when they use gasoline to start fires.
Many thanks for the video... just changed mine out --- piece of cake and got the gauge working again on a Dargel Skout 186.
Awesome video straight to the point and very informative thank you for taking the time to do this
i have yet to NOT find a video i need on here, good stuff man.
Thank you
you measured incorrectly for your tank it should have been 7 13/16 or 198mm. not 7 3/16. also you forgot to mention the 5/16 less than proper arm length which is what gives you the emergency gas when gauge reads empty. but a fair video anyway.
So would the arm length need to be 7½"?
Thank you for posting this video , I’m in the process of replacing/checking my fuel sending unit , very informative
I hope your repair goes smoothly. Just make sure you put enough sealant on the screws so the gas doesn't leak
Thank you. Very precise and easy to follow demonstration. Very Helpful.😎
Wow, brevity is a lost art, ty
thanks for the video! just picked up a complete sending unit kit at a swap meet!
Thanks I got the same unit I'll install it this weekend.Great vid!
Glad it helped
Freaking great video, short and to the point.
Who buys a new fuel sending unit to test? Rest of the video is good. I prefer to trouble and then buy. Not buy and then trouble shoot
Precise and easy to follow video. Thank you!
Thank you. Hope it was helpful
Fast and to the point thanks
Same comment, man. Thank you for getting to the damn point.
Great video going to change mine soon my gauge never has worked
Nice and to the point. Wish all RUclips videos where like this.
Thank you. I am not here to waste anyone time.
Thanks for this video,helped me install my sending unit perfectly.I think you should make another video ,detailed in the wiring the sender to the gauge and to ignition etc,thats where I'm lost,I suck at anything electrical,there's no good videos on this,you could do a good job,at it.
Shazam simple fast straight to the point thank you!
Great video! Short sweet to the point. Excellent. 👍🏼👍🏼
Thanks for no extra bullshit perfect tutorial you rock bro
Thanks a lot - I need to do that job and it was very informative
Great job dude. You made it look easy.
Absolutely fantastic video. Thank you.
Something that I haven't seen covered is that older cars may have a copper float which can leak. If it fills with fuel it will sink and always read empty.
Super helpful thank you! Just wondering if it's worth repairing my fuel sender which always reads full!
Straight to the point!!!!!!! NO BS
Great Video
Got to the point. Great video.very helpful.
great video, straight forward and to the point
Glad I didn't waste your time
@@BigIslandMNMinnetonka im about to replace the fuel sender on my boat so this vid helped. thx again
@@salimsopari glad it helped.
Thanks, man ! I’m doing this tomorrow !
Good luck. Seal screws well!
Nice info thanks. Is it possible to check the old fuel sender with a multimeter.
Great video no fluff to the point
Are all the holes the same?? Mine just broken the wire off in the tank. It also seemed that my gauge was off by a half tank. I did touch the wire back to the point and my gauge did move. I which is the longest lasting gauge available. I know fuel is everyone's best friend
No the holes are not the same you must orient the lever the same as the old one, but you can't do it wrong or the screws won't go in
Dude.. great vid and to the point. Much appreciated!
Thank you. Hope it helped
Thanks Chris.. you are champion!!
you're the best I learned a lot from you
Thank you
your videos are really helpful. thanks. when i winterized my boat last year, i used the antifreeze and ran it through the entire system like you showed in your video. my boat started up on the first shot this spring. my question is, when i ran the boat with the ear muffs with the water, i noticed an oily chemical mixed in with the water coming from the exhaust. is that the residual antifreeze that was in the system. thanks. the boat ran great on the lake. its a 97 bayliner capri classic 2050. merc,350
When I turn the key, the fuel gauge shows full, when I turn the ignition off, it shows empty.
Tested sensor with measuring instrument it has the correct Ohm value.
It is both a wema and a wema instrument. Has worked before and also not replaced anything previously. When I disconnect the sensor's 2 cables it still shows full. what do you think is wrong then?
Thanks for sharing. 👍
THANKS QUICK AND TO POINT, THANKS.
Great video, sort and direct to the point.
I hope it helped you.
Great vid. Efficient lesson.
I'm going to try this today. Is it OK to leave that much (looks about 1/4") of play on float between stoppers? Why would you want it to slide back and forth?
I don't think it matters
I'm trying to find my sending unit. Could it be under a seat? I pulled the floor vent and nothing under it but the fuel outlet.
Thanks for the very well explained video I will try to change my fuel level sensor on my 1997 celebrity
It is very easy. Just make sure the new one seals good. And the new screws.
Top class easy instructions. Good one!!
Excellent presentation and thank you.
Ok tank you ser....
.
Hope it helped
Good video mate
I need help with mine well you see the thing that you replace well I don’t think mine is working because I took both original tanks out and my dad bot me a new aluminum tank for the bed and it had that float think like your’s but this new tank of mine has ouly one wire plug on it and yours was 2 but my old tanks had 3 wires plugged into it so witch wires do I use for this new tank I have 3 opinions a red a black and the blue wire has power so I tried hooking up all 3 with no response but blue wire with power makes the fuel gage go up to full no matter if the float is up or down I need so help
nice, thanks!
Nice video, but I would have liked to have seen a wiring schematic to go along with it. But thanks for the info!
Great vid! Quick and to the point. Thanks mate!
Your welcome. I hope it helped
Great instruction
So easy!! I have to change mine. Thank you for this!
It is really easy. Just make sure you don't tighten the screws to tight. Just right enough for the rubber to seal
Awsome great info
U dont scare of any spark caused by metal tools?
Awesome video. Thank for sharing.
Great Video!! What sealant did you use? I'm replacing mine tomorrow.
Permatex #2 , gas resistant . Found at any auto parts store
Concise. Awesome. Thanks!
Thank you
Great vid. When you say "some type of sealant" for the screws. What do you recommend ? Permatex ?
Somthing that works with gas. You don't want gas to eat through it.
Permatex #2 is gas resistant
@@ericmaass3459 that is what I ended up using. It worked good.
@@ericmaass3459 thank you
Did I hear correct/,he said 7. 3/16 should be 7. 13/16.
I miss spoke.
@@BigIslandMNMinnetonka No, you cut to short....
@@BigIslandMNMinnetonka What you have effectively done is provide yourself with some "emergency" gas. Your gauge will read empty but you'll still have 5/8" of gas left in your tank. I like it. :-) Great video.
@@healthstartshere666 all intentional. 🤥
Hi my tank is leaking gasoline from where the tap where where the part at , how can I fix the leak it’s just a little bit but I don’t wanna use like that
I'd add that many many times with boat electronics the problem is nothing more than a bad connection due to corrosion, before you bought a new sender you should have removed the old one, cleaned the connections, checked the wiper are to make sure it was in contact with the resistive wire then lifted and lowered the float with the key on and see if it starts working. Most times it does, other than a bad connection or mechanical damage the only thing that goes wrong that isn't easy to fix is the float might sink.
Nice work.
@@BigIslandMNMinnetonka unfortunately after a long paddle to the shore whilst avoiding a barge or two I had plenty of time to troubleshoot the issue while I waited for my buddy to go get a jug of fuel....
Measure twice, cut once.... the book said 7-13/16 and you cut it 7-3/16... your tank was just over half full, and your gauge is reading 3/4 full.. that 1/2 inch you fucked up on is throwing your gauge off.. but its close.. and it will work...
I miss spoke. I do it alot
Thank you but - it was 7 and 13/16 not 7 and 3/16, One half inch of swing cut off the sender. Will probably make readings at full and empty a little off, measure 2x cut once.
I am finding that not all fuel gauges are the same and you need to match a sending unit with the gauge. With a broken sending unit how do you know which one to buy to match your dash gauge OHMS RANGE?
The one I put in is universal. It should work in most tanks. Maybe now in the newer boats
As long as you have a ground wire and negative wire running to the fuel sender it should work with the universal.
My fuel gauge goes up and down with the water and motion of the boat, I was told it was a ground issue but I checked ground and it's good.
That sounds normal. If your boat is going up and down with the water, your fuel is too.
It's supposed to, the boat is moving. Cars would do that too, but they're digital and have circuitry delays built in so that they don't move around every time you take a turn.
You reference a chart to get the proper depth to cut the level arm. Where is the chart?
Each gage had it's own chart
did that float length chart come with the new fuel sender?
It did with the sender I bought
I put mine and the gasket didn’t seal right..... gas pours out no matter how tight or loose I tighten the sender. It never leaked with the old unit on... Any suggestions on what type of sealant I can use that the gas won’t eat up????
Talk to a marine service center. Make sure you put sealant around the screws
The yellow tube at the auto parts store, seal all I think it is
Thank you
Thanks, dudeman!
I hope it went easy for you.
Thanks for sticking to the meat of the subject and leaving out a whole lot of time filler bs.
I cut mine short! Is it screwed?
My tank is 12” deep and I measured the arm to make sure it could reach the bottom and top having 12” of travel. But I cut it to like 6” (6” up and 6” down)
I should be fine right?
I hope so. It might show less gas than you have. You might just have to try it out.
Big Island MN yea that was my logic. I would rather play it on the safe side and show empty earlier than not.
I only have about 1” of gas left out of my 12” deep tank. So it’s not wrong I’m pretty empty. Like you said I’ll just have to find out on my next full up.
SOLID !!!
It was 7-13/16” not 7-3/16 but prolly
close enough
Yes. Lol
Thank u 🤙
Umm that was 7-13/16
I thought it read 7 13/16", not 7 3/16"
You are correct. I said it wrong.
where's the part about how to test your old unit?
Turn the key on and move the arm up and down.
The sender looks like it's from a FORD PICKUP.
You aren't testing you're replacing. Surely you test before you buy anew one. If the new sender still gives the same as the old one you've just wasted money
It doesn't get anymore to the point than that
throw that tinker toy in the trash can get a reed switch fool proof
🇩🇰😮❤
Please give me one iPhone please please please
Give me one
Looked like OEM was a right side float, correct? How did a straight float arm work for this? Why did you not bend the float to the side?
It worked perfect. No need to bend it. It had room