Это видео недоступно.
Сожалеем об этом.
HOW TO CHECK CYLINDER HEAD Part 1
- Добавить в
- Мой плейлист
- Посмотреть позже
- Поделиться
Поделиться
HTML-код
Размер видео:
- Опубликовано: 19 ноя 2022
- HOW TO CHECK CYLINDER HEAD Part 1 #shorts
Комментарии • 35
Следующие
Автовоспроизведение
Diagnosing a Bad Head Gasket: How to Spot the Telltale Signs So You're Not Ripped Off.Repair Geek
Просмотров 468 тыс.
Do We EVER Grind Valve Seats These Days?Jim's Automotive Machine Shop, Inc.
Просмотров 183 тыс.
AMAZING Idea With An Ax !Alva Welding
Просмотров 34 тыс.
HIGHLIGHTS | NEW ZEALAND v ARGENTINA | The Rugby Championship 2024TRC & SUPER RUGBY PACIFIC
Просмотров 693 тыс.
Live stream for Elon Musk-Donald Trump interview crashesFOX 11 Los Angeles
Просмотров 590 тыс.
【MV】Breaking Dimensions【hololive English Original Song】hololive English
Просмотров 327 тыс.
Can You Forge Tungsten?Alec Steele
Просмотров 805 тыс.
Warped Cylinder Head Straighten Resurface in the GARAGE DIYsixtyfiveford
Просмотров 222 тыс.
$22 magnaflux DIY to check 4 cracks at homeDiscoGreen
Просмотров 13 тыс.
Sleeving an Engine - Part 1Engine Builder
Просмотров 68 тыс.
Willys Flat Head resurfacingWatson's Wagons
Просмотров 1,4 млн
HOW TO CHECK FOR A BLOWN HEAD GASKET2CarPros
Просмотров 4,6 млн
Did Stevie Wonder start porting heads?!HeadGames Motorworks
Просмотров 110 тыс.
How To Remove and Replace Valves in a Cylinder Head -EricTheCarGuyEricTheCarGuy
Просмотров 1,3 млн
Car engine cooling systemSanya Tsvay
Просмотров 4,5 млн
How to Resurface a Cylinder Head at HomeBroomy's Garage
Просмотров 134 тыс.
ВРАГ В ШОКЕ! СДЕЛАЛ КД 1 СЕКУНДУ и ВЫНЕС ВСЕХ #blitz #tanksblitz #shortsnYJI9 TV
Просмотров 119 тыс.
Sevinch Ismoilova - Xayollarim 18-Avgust 19:00 PremeraSevinch Ismoilova
Просмотров 153 тыс.
Переехал на танке дом 😱 #shorts #start #кино #фильм #сериал #противвсех #танкиSTART
Просмотров 14 тыс.
И Я ПОЗНАЛ СОВЕРШЕНСТВО. 911 turbo SAcademeG
Просмотров 846 тыс.
ТОП-6 САМЫХ БЕСЯЧИХ ЗОМБИ ДИКОГО ЗАПАДА! / PVZ 2IGRARIUM - Игровые обзоры
Просмотров 264 тыс.
Хитрость старого мастера #diyGARAGE 100
Просмотров 55 тыс.
GAVRILINA - Drama Queen (ПРЕМЬЕРА КЛИПА 2024)Julia Gavrilina
Просмотров 506 тыс.
Безумно вкусная кабачковая тортилья 💚Анна Бондарь
Просмотров 109 тыс.
Also would like to know: why the seam ripper?
Had it in my pocket from a different job
In my country where gas is $10 a Gallon, (was $5 when Trump was in) we never had mass production large capacity cars. Is this a Diesel or Petrol
As a mechanical inspector from the precision machining industry I would do it on a surface plate using a dial indicator to sweep the surface. You need three points on the surface to establish the zero reference plane so the indicator will read zero at three designated spots. Two on the same end in the corners and the third on the opposite end central to the head width. Mark these spots with a dot using a sharpie and orientate the head resting on three finger jacks (on the underside of the head)located roughly opposite the marked spots. When you have zero at all three spots then sweep the rest of the surface for the largest departure from the zero reference plane. The total indicator reading is flatness of the surface.
Hard for the home guy to do as most don’t have good straight edge. In my experience heads should just be resurfaced and be done with it
@@CUTTERUPROB agreed!…can’t spend all day on it!😆…on my ‘97 12 valve I’ve encountered hills pulling my 5th wheel where I’ve had to pull it into low and stay in the truck lane and noticed my boost wouldn’t go above 17-18psi so it lacked power…any ideas? Has a Banks power pack,straight pipe,adjustable ofv and boost elbow…no major mods.
Heads aluminum, block is cast. The markings on the block are just a stain from the gasket but those heads are definitely bad.
Put a straightedge on it with feeler guages to tell how bad it is, people have been doing it for decades.
You never said how a shop checks if a head is flat.
They use a long machinist square. Usually about 1/4 in thick but 2 or 3 foot long.
@@mustangdemon87 yeah I knew that but it's the opening of the video and never explained.
video's coming
Thats what I was watching for....disappointed 😔
If I had access to a calibration lab I could put it on a surface block that was calibrated to one ten thousanths and put a runout gauge on it but I do not do cylinder head work.
What's with the seam ripper
Was in my pocket from a different job I was doing
Makes an effective pointer. Gives size reference to the wear.
So you would check the block deck right?? Just because the head has been decked doesn’t mean you’ll get a good seal.
Yes you would want to as well. I need to finish this series of videos
@@CUTTERUPROB sounds good!
Ok so how does the shop check it you never did say in this video
Seam ripper come in handy with electrical harnesses.
thats funny that why it was in my pocket
No offense didn't show us or tell how, just described why, and that you knew. Good info.
More videos coming
Fire ring it.
Thanks for the very useful information.
What might be the cause after resurfacing and over heat keeps persisting..
Could be a bunch of things. Water pump / rad / t stat / air lock etc .
.....oil cooler, egr cooler.
After sewing class
Stripping a working harness
Wow, genius tool for ripping into a harness 👌
Thanks 👍
Carefully!