It originally read 31mm because of the material removed being the thickness of the cutoff wheel. Fyi for future ventures, just trust your original marks :)
I’m at the point that I don’t even need notifications of new YS uploads. I feel it like in my intuition he’s uploaded already so I check. I’m not getting notifications. And I pressed all YS notifications. But I’m here and yay for that
Hey D my apologies I don’t want to offend you by spelling your name wrong. I’m a big fan love your videos I have plans on k swapping my 96 civic I was wondering if you could give me some guidance on something’s such as can a k20 top end fit a k24 bottom end and if so what I series are they to be exact
i used a 260 volt line for a stick welder to weld a 1 inch 4340 axle on the car 1/8'' E7018 at 165amp it held the 100'000psi to the 4918 process for a long time... tripping the brakers is a good indication of power, tripping a 30amp 220volt doing structural stuff is also fine... unless the house is wires with aluminum wire, don't want to load those up. "the dryer plug only has 3 wires, the stove has 10 more amps but its a 4 wire, colors like diffusing the bomb in a S&D match... ninja diffuse... why dryer take so long? one thing or the other, get paid more for the other use. shops in my local city have a $155/hr flat rate for that kind of stuff.
@@2LegitTooQuit those multi process inverter welders only run so long, have an old 260 volt 60amp for the Lincoln AC welder, duty cycle is very low but it always works... trips a 40amp braker in 25 seconds running at 120amp. think the switch contactor needs to be cleaned old rusty trusty... just a coil of wire no nonsense. 300 pounds of weld to a micro process welder. 225amp AC buzz box lives forever.
That was a cool project to take on Dana. Had know idea you knew Thomas from Illiminate. Would be cool to see him on this vlog. Haven't seen him around in the Illiminate videos for a good long minute. Another great banger bruddah!
![Lil Uzi Vert - Chill Bae [Official Music Video]](http://i.ytimg.com/vi/D7F42F_JM3U/mqdefault.jpg)
Progress is better than no progress 💯
I know Thomas from watching illuminate videos !! That’s cool that your helping him out !
surprised he didnt go to luke honestly he knows alot when it comes to mechanical stuff
It originally read 31mm because of the material removed being the thickness of the cutoff wheel.
Fyi for future ventures, just trust your original marks :)
I’m at the point that I don’t even need notifications of new YS uploads. I feel it like in my intuition he’s uploaded already so I check. I’m not getting notifications. And I pressed all YS notifications. But I’m here and yay for that
Nice job. And great idea on the extending the arm. Good process.
We need Merch on this channel..
Facts
Some “No Mames” shirts 😂
I would buy anything and everything……
#Pibtnp
Palabraa
Damn, I miss seeing him on their channel
Looks mint I would trust that way more than just the boxing in style.
On my element the front bushing on the lower control arms was bad. I replaced them and no more noise
You can rock the element side to side and see if the noise is coming from the end links.
Love the is300 content
ayeee bumpin that Russell!
Wonder if Thomas still got his Honda prelude
Illuminate in the house!! Thomas
You are amazing with your build God bless you and you are legend on your build WOW THAT'S WAS UP.
Brooo i love the is300 content
Hey D my apologies I don’t want to offend you by spelling your name wrong. I’m a big fan love your videos I have plans on k swapping my 96 civic I was wondering if you could give me some guidance on something’s such as can a k20 top end fit a k24 bottom end and if so what I series are they to be exact
Looks great… love watching
i used a 260 volt line for a stick welder to weld a 1 inch 4340 axle on the car 1/8'' E7018 at 165amp it held the 100'000psi to the 4918 process for a long time... tripping the brakers is a good indication of power, tripping a 30amp 220volt doing structural stuff is also fine... unless the house is wires with aluminum wire, don't want to load those up. "the dryer plug only has 3 wires, the stove has 10 more amps but its a 4 wire, colors like diffusing the bomb in a S&D match... ninja diffuse... why dryer take so long? one thing or the other, get paid more for the other use. shops in my local city have a $155/hr flat rate for that kind of stuff.
That’s assuming his range is on a 40amp circuit. They could easily be on a 50amp.
@@2LegitTooQuit those multi process inverter welders only run so long, have an old 260 volt 60amp for the Lincoln AC welder, duty cycle is very low but it always works... trips a 40amp braker in 25 seconds running at 120amp. think the switch contactor needs to be cleaned old rusty trusty... just a coil of wire no nonsense.
300 pounds of weld to a micro process welder. 225amp AC buzz box lives forever.
Need to make bigger gauge extension cord to illuminate the tripping of breaker's
Thomas! From illiminate!
Yes youngstatic merch😂
SOME progress is better than no progress, SOME...
Let's goo!!!
So the MR. illuminate big shot too good to make an appearance on you show ? damn that's messed up
Yes I
I've extended my lower control arms when bagging my 94 civic coupe, necessary for bagging older civics.
How much did you extend them
Great job.
Good job dana. ✌🏻🇳🇱
I love it! When is it not a late start though?!😂
That was a cool project to take on Dana. Had know idea you knew Thomas from Illiminate. Would be cool to see him on this vlog. Haven't seen him around in the Illiminate videos for a good long minute. Another great banger bruddah!
they all local to each other nd everyone went separate ways now
Did you look into lower extension plates any?
IS Gannnng! 🔥
What mig and tig do you have
Is Thomas still affiliated with illiminate?
I heard he parted ways because of too much drama around
What is they name of the song at the end of each video
What wheels are on the Lexus??
Dana you should get a colab going with illiminate...would be good content
hell naw rather have Dana do his own thang
Just bought some stock LCA's for my is300 they should've arrived by now :/
Should have worn gloves…🤣 No mames had me 💀 😆
I miss my IS after watching this😢
Collab.. lets gooo
WY you get another arm at junk yard and use same material
Niiice haven't seen that lexus in a long time lol
Nice 👍🏼
Safety glasses. n_n
Edit: Oh god your hair. If that gets sucked up into the angle grinder.... that's sooo scary T_T
Bro just for your safety, watch out with your hair while grinding.
Bro go to the dermatologist