hi Joe I think you are saying the machine makes the pierce but the flame goes out even though the program runs . I think your machine is looking for a flame ok feedback. with no feedback it turns off torch. you need to go into setup and turn off this parameter.
I have the same problem as Joe. My machine makes the pierce but flames out but mine does not run after it flames out. It just stops. I have cut on it before, but now this problem poped up and I can't figure it out.
Have you looked at all the parameters re flame running feedback.if it has been enabled because there is no feedback circuit it thinks there is no flame and turns off the torch. If it also stops running the shape program that could be another problem. I am not familiar with this problem. Look at the troubleshooting guide.
there are only 4 wires fom the cnc controller. 2 for on of switch using a relay. 1 off + 1 off - for torch height control 50:1 input. you have to work out what wires your machine has.
@@TiffanyMartin50 I guess you are asking about the wiring depending on how your divider board is configured in your controlled. ours can accept 1:1 Voltage or 50:1 voltage depends how it is configured with the jumper etc. you electrician need to check what output Volts your Plasma source THC wires are putting out. say 80 volts or 1.6volts. and configure the devider board to match.
I am not sure what you mean but this is a link to the corrigated iron cutting on my playlist: ruclips.net/video/lxowvqgMb8k/видео.html&ab_channel=ColeToolCentre
Hi guys I have just bought a CNC WITH THE SAME CONTROL PANEL AS IN YOUR VIDEO.I AM A HOME HANDY MAN BUT NOT COMPUTER MINDED JUST YET I AM WORKING ON IT.IVE BEEN WATCHING YOU VIDEOS THANK YOU THEY HAVE HELPED ME HEEPS .I JUST WANTED TO KNOW HOW DO YOU GO FROM TEST RUN TO A LIVE CUT .I CANT SEEM TO FIND MY WAY OUT OF TEST RUN PLEASE CAN YOU HELP ME CHEERS
@@engmec.joseantonio4181 the gcode is loaded on a USB stick and runs machine. NC. Text. The gcode commands are all explained in the machine manual. Fastscam should work with windows 10 what is the problem.
The only problem I have seen with windows 10 is the USB port will not read the usb key. USB port problem. The cure seems to be use an external USB hub.
Yes. if you were cutting it. Because of the cut order the square would have been cut out and fell through. but that particular drawing is only in the library as it is usually only used for testing the machines for correct movement of cutting head.
hi , thanks for video , i see it is with THC , is it HF OR HT OR BLOWBACK arc pilot what could you advise for , cnc cutting , thin metal as hvac thanks need to purshase one of it thanks
Naoufel Melayh the THC uses voltage to control hright. You need a signal from your Plasma source you set a target voltage for cutting if voltage actual is high torch moves down if actual is low torch moves up. For flame it uses a capacitance ring I don't know how it works as I don't use flame.
Sorry for late reply The THC is controlled by voltage on Plasma. It has a capacitance ring on Gas (i don't know how this works but it seems to be controlled by proximity)
I didn’t get a Manual with it Sir I was able to do like your video any chance of Messenger video from you would be very much Appreciated if this is Possible
You should be able to get a similar manual here www.google.com.au/url?sa=t&source=web&rct=j&url=www.omni-cnc.com/wp-content/uploads/2016/03/Plasma-2012AH-Controller-Manual.pdf&ved=2ahUKEwjw4MiLicfeAhUXVH0KHfW5DVQQFjAAegQIBxAB&usg=AOvVaw0XiJicFtgU44ZdzKSxNqko
The machine comes with Fastcam which is a CAD CAM and save as a g code which you can save to USB and run or save your cut file to the machine
hi Joe I think you are saying the machine makes the pierce but the flame goes out even though the program runs . I think your machine is looking for a flame ok feedback. with no feedback it turns off torch. you need to go into setup and turn off this parameter.
I have the same problem as Joe. My machine makes the pierce but flames out but mine does not run after it flames out. It just stops. I have cut on it before, but now this problem poped up and I can't figure it out.
Have you looked at all the parameters re flame running feedback.if it has been enabled because there is no feedback circuit it thinks there is no flame and turns off the torch.
If it also stops running the shape program that could be another problem.
I am not familiar with this problem.
Look at the troubleshooting guide.
Any way you could show the wiring to the plasma cutter? Thanks in advance
there are only 4 wires fom the cnc controller. 2 for on of switch using a relay. 1 off + 1 off - for torch height control 50:1 input. you have to work out what wires your machine has.
@@Graemecns I have the same one as you. starfire model! What amp would I need?
@@TiffanyMartin50 I guess you are asking about the wiring depending on how your divider board is configured in your controlled. ours can accept 1:1 Voltage or 50:1 voltage depends how it is configured with the jumper etc. you electrician need to check what output Volts your Plasma source THC wires are putting out. say 80 volts or 1.6volts. and configure the devider board to match.
Kindly upload a video for control the arc of cnc plazma
I am not sure what you mean but this is a link to the corrigated iron cutting on my playlist:
ruclips.net/video/lxowvqgMb8k/видео.html&ab_channel=ColeToolCentre
Hi guys I have just bought a CNC WITH THE SAME CONTROL PANEL AS IN YOUR VIDEO.I AM A HOME HANDY MAN BUT NOT COMPUTER MINDED JUST YET I AM WORKING ON IT.IVE BEEN WATCHING YOU VIDEOS THANK YOU THEY HAVE HELPED ME HEEPS .I JUST WANTED TO KNOW HOW DO YOU GO FROM TEST RUN TO A LIVE CUT .I CANT SEEM TO FIND MY WAY OUT OF TEST RUN PLEASE CAN YOU HELP ME CHEERS
The information should be in your manual but to turn off Test Just push the X Test Button to toggle off or on.
ye kitne ki hai or kahan se mile gi
is it possible to generate the code in Artcam? I can't find the format of the post processor, that is, the format of the NC code
I am not Familiar with artcam but the machine uses gcode.
It usually comes with Fastcam software.
@@Graemecns I couldn't install Fastcam, my windows is 10, I'm trying Artcam but I don't know what is the file format or the post processor
@@engmec.joseantonio4181 the gcode is loaded on a USB stick and runs machine. NC. Text.
The gcode commands are all explained in the machine manual.
Fastscam should work with windows 10 what is the problem.
The only problem I have seen with windows 10 is the USB port will not read the usb key. USB port problem.
The cure seems to be use an external USB hub.
Wouldn't it fall after it's done with the square?
Yes. if you were cutting it. Because of the cut order the square would have been cut out and fell through. but that particular drawing is only in the library as it is usually only used for testing the machines for correct movement of cutting head.
Does it allow your own .dxf/.dwg designs to be loaded, or just the internal preset shapes?
hi , thanks for video , i see it is with THC , is it HF OR HT OR BLOWBACK arc pilot
what could you advise for , cnc cutting , thin metal as hvac
thanks need to purshase one of it
thanks
Naoufel Melayh the THC uses voltage to control hright. You need a signal from your Plasma source you set a target voltage for cutting if voltage actual is high torch moves down if actual is low torch moves up. For flame it uses a capacitance ring I don't know how it works as I don't use flame.
Sorry for late reply The THC is controlled by voltage on Plasma. It has a capacitance ring on Gas (i don't know how this works but it seems to be controlled by proximity)
Please help me with starfire cam tutorial video
There is plenty of videos on RUclips for star fire also when you get your controller make sure you get a manual. It will go into depth on gcode etc.
Thanks I have worked it out
Bro I need some help
I can but try to help what is your issue?
dear sir how do you change language from chinse to English
zelalem shitaw check you tube video m.ruclips.net/video/0zinWMCt5u8/видео.html
Change language see you tube video m.ruclips.net/video/0zinWMCt5u8/видео.html
I didn’t get a Manual with it Sir I was able to do like your video any chance of Messenger video from you would be very much Appreciated if this is Possible
You should be able to get a similar manual here www.google.com.au/url?sa=t&source=web&rct=j&url=www.omni-cnc.com/wp-content/uploads/2016/03/Plasma-2012AH-Controller-Manual.pdf&ved=2ahUKEwjw4MiLicfeAhUXVH0KHfW5DVQQFjAAegQIBxAB&usg=AOvVaw0XiJicFtgU44ZdzKSxNqko
Hi , You are helping my drawing gives the error
This is SF2100S controller made by china Starfire.
www.qihuacnc.com
Hi all, anyone can share fastCAM software ?
Nyc