The best of no worlds. Not as stiff taking a turn on the road so the Jeep leans more. But it is a smidge more stable off road & that's a fair trade off for me.
@@KTMcaptain I've used the Evo product on past jeeps and it works great but my next "fix" will be the antirock simply because I'm not to old to get down and turn a knob I'm to old to get back up lol
@@teddonley9594 you should check out the TTO pneumatic rubicon sway bar actuator then. It is faster, stronger, and more reliable than the oem actuator. The anti rock is worst of both worlds. It limits flex, slightly, but doesn’t do much for limiting body roll since it lacks the torsional rigidity to resist flex. To each their own though. You can sell your Rubi bar for the price of that anti rock.
@@teddonley9594 EVO also builds a pneumatic actuator for the Rubicon Electric Sway Bar: www.northridge4x4.com/part/disconnects/1152-evo-no-limits-on-demand-sway-bar-disconnect
Ive got the jks quick disconnects, you have to cut a piece off to make them work on the passenger side, if i was to order the antirock will it still work with that piece cutoff?
Either one is pretty good. The Apex will be act like stock when locked in on the street. The Anti-Rock will be have a little more body roll on the street.
The JKS sway bar quick disconnect’s or any other aftermarket brands are still the way to go. Might be only a little over an inch 🤏 but in terms of off-roading that is still more flex. This has more potential to bend, strip or break a component on this setup and manufacture design, to many parts. So basically an overpriced front end decoration piece like any after market front steering stabilizer shock. But as always GREAT Video 👍
If it's nearly the same amount of flex as a disconnected one, then why not just run without a sway bar? Clearly this one doesn't do much in the way of generating spring force to correct body roll.
@@northridgenation it’s a direct function. If it barely resists the unloaded axle moving then it will barely resist the body. It’s physics. I drove around for years without a sway bar. Especially when a vehicle becomes loaded up on the roof with RTT and other gear. Unless it has some system like KDSS which disengages part of the bar when the front wheel articulates and the rear doesn’t it will always work proportionally to it’s torsional force. It’s simply a very weak torsion rod. . Now, have they made it where you slide the end link mounts up and down that arm… then you can have a strong bar on the road and a loose one off road… then it could be fine. . But you can’t say it can handle a 5000 lbs load at 60mph when a single spring and some axle weight can flop it over. That’s far too much kinetic energy and far too little force it generates.
We haven't tried that combo, so we can't say for sure. But we're going to guess that if you're having issue with a stock bar, this will be about the same.
@@northridgenation the stock sway bar doesn't rub. I was wondering if the antirock forged arm follows the same bend line as stock and in general doesn't sit wider than stock sway bar at the end links?
It's has more body roll than stock, but it's not bad. Guess it will really depend on your personal tastes. If you think the stock sway bar isn't stiff enough, then this will definitely be too soft.
This video didn't explain or show the hardest part of the install which is how to determine the sway bar link size and how to determine the angle of the sway bar arms. They aren't bad to put on but the way he installed that didn't look right at all.
![Blox Fruits Dragon Rework Update [Full Stream]](http://i.ytimg.com/vi/EqDAp8udhm0/mqdefault.jpg)
I use Apex Quick Disconnects. Stable on the highway and it takes a second to disconnect.
The best of no worlds. Not as stiff taking a turn on the road so the Jeep leans more.
But it is a smidge more stable off road & that's a fair trade off for me.
Thank you. I thought the same. Figured I watch some videos but none have made me think this is a better way to go
I'm using the factory rubicon electric disconnect. Until it breaks lol
Evo makes a no limits manual disconnector for the Rubi sway bar... Team Tech Offroad makes a pneumatic actuator for it.
@@KTMcaptain I've used the Evo product on past jeeps and it works great but my next "fix" will be the antirock simply because I'm not to old to get down and turn a knob I'm to old to get back up lol
@@teddonley9594 you should check out the TTO pneumatic rubicon sway bar actuator then. It is faster, stronger, and more reliable than the oem actuator. The anti rock is worst of both worlds. It limits flex, slightly, but doesn’t do much for limiting body roll since it lacks the torsional rigidity to resist flex. To each their own though. You can sell your Rubi bar for the price of that anti rock.
@@teddonley9594 EVO also builds a pneumatic actuator for the Rubicon Electric Sway Bar:
www.northridge4x4.com/part/disconnects/1152-evo-no-limits-on-demand-sway-bar-disconnect
Need one for my JT Gladiator Mojave
You gain more flex but it’s more unstable on highways
Ive got the jks quick disconnects, you have to cut a piece off to make them work on the passenger side, if i was to order the antirock will it still work with that piece cutoff?
Rockjock sells that tab to be welded back on. I had this very issue!
Stick with what you have. You will thank me later.
Apex disconnects or anti rock? If one had to choose for a 3in on 35s load bearing jeep. Can’t decide have to get rid of my jks quickies.
Either one is pretty good.
The Apex will be act like stock when locked in on the street.
The Anti-Rock will be have a little more body roll on the street.
The JKS sway bar quick disconnect’s or any other aftermarket brands are still the way to go. Might be only a little over an inch 🤏 but in terms of off-roading that is still more flex. This has more potential to bend, strip or break a component on this setup and manufacture design, to many parts. So basically an overpriced front end decoration piece like any after market front steering stabilizer shock. But as always GREAT Video 👍
I felt the same. Right on the money.
These things play nice with the Mojave variant of the JT?
Yes they do.
@@northridgenation thank you, good to know. will be placing an order for one when funds permit, not about that disconnect life 😂
If it's nearly the same amount of flex as a disconnected one, then why not just run without a sway bar? Clearly this one doesn't do much in the way of generating spring force to correct body roll.
They actually help a lot over no sway bar. But they do have more body roll than the OE sway bar.
@@northridgenation it’s a direct function. If it barely resists the unloaded axle moving then it will barely resist the body. It’s physics. I drove around for years without a sway bar. Especially when a vehicle becomes loaded up on the roof with RTT and other gear. Unless it has some system like KDSS which disengages part of the bar when the front wheel articulates and the rear doesn’t it will always work proportionally to it’s torsional force. It’s simply a very weak torsion rod.
.
Now, have they made it where you slide the end link mounts up and down that arm… then you can have a strong bar on the road and a loose one off road… then it could be fine.
.
But you can’t say it can handle a 5000 lbs load at 60mph when a single spring and some axle weight can flop it over. That’s far too much kinetic energy and far too little force it generates.
Does this have clearance issues at full lock or full flex on stock rims with 285 or 315 tires?
We haven't tried that combo, so we can't say for sure.
But we're going to guess that if you're having issue with a stock bar, this will be about the same.
@@northridgenation the stock sway bar doesn't rub. I was wondering if the antirock forged arm follows the same bend line as stock and in general doesn't sit wider than stock sway bar at the end links?
@@graywolf.overland It is no wider than the stock set-up, if anything it might have just a bit more clearance.
How’s the body roll on a daily though?
It's has more body roll than stock, but it's not bad.
Guess it will really depend on your personal tastes. If you think the stock sway bar isn't stiff enough, then this will definitely be too soft.
@@northridgenation thanks 🙏
This video didn't explain or show the hardest part of the install which is how to determine the sway bar link size and how to determine the angle of the sway bar arms. They aren't bad to put on but the way he installed that didn't look right at all.