Which Parts to grease when installing a clutch. Release Bearing installation Throw out bearing
HTML-код
- Опубликовано: 12 июл 2024
- Centerforce clutch (verify compatibility when checking out) amzn.to/3sJlFks
Ford racing throwout bearing amzn.to/3IYZDQN
Transmission jack sold here amzn.to/3vAxImd
High temp grease amzn.to/35MeRJZ
Clutch fork (highly recommended) amzn.to/3tw3Nsx
Pilot bearing amzn.to/3Kgnlbo
Pivot ball stud 79-04 for Ford Mustang Clutch Fork Pivot Stud, T5/T45/TR3650 amzn.to/3MlJsPj
If you enjoyed this video and wish to donate $5 to support my channel, please visit the following link!
www.paypal.com/cgi-bin/webscr... Donation Support
Disclaimer: I am an amazon affiliate and may receive a commission for sharing the link, but the price will be the same for you.
This video shows how to replace a clutch and it's components. This is a VERY dangerous task. This video is for demonstrational purposes only. Make sure the car is properly secured on jack stands, wear safety glasses, etc. The transmission and many of its components are very heavy and sharp !! I assume absolutely no responsibility for injury or death that occur if you attempt this repair.
The concepts performed in all videos from Scrun Johnson are for demonstration purposes only and are not guaranteed in any way as I am not a certified mechanic. The viewer holds the responsibility to research these procedures and perform them at his/her own risk.
Due to factors beyond the control of Scrun Johnson, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. Scrun Johnson assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Scrun Johnson recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of Scrun Johnson, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not Scrun Johnson. Always take proper safety precautions, including, but not limited to, wearing safety glasses, removing jewelry, properly securing the vehicle on jack stands, etc.
Cómo cambiar el embrague 
Хобби
I enjoyed your video Danny. Knowledge like this is invaluable for many of us who are doing the clutch install ourselves! Greasing all the right places can prevent many future clutch issues and pain in the neck noises caused by metal against metal friction or premature parts wear from failure to lubricate them correctly.
Your videos helped me alot I appreciate it
I’m glad to hear that. Thanks!
This is great info on clutch installation, I've been having problems with my clutch cable hanging up. I just ordered BBK cable and firewall adjuster. Any tips on installation? Really like your channel and your brothers. Great stuff!
i’m pullin the motor in my 01 GT and i can’t find your starter removal video, but dude i fuckin love you. i could not get out that top starter bolt to save my damn life. you made it look so easy on that termi. i was like there’s no way it’s that easy but sure enough it was. you are much appreciated ❤️❤️❤️❤️
zayuhtoven It’s much easier with the exhaust off first, and a 1/4 inch drive little ratchet helps getting on it.
Hi. My 03 Yaris won't select gear intermittently. I notice the slave is not leaking and seems to operate the fork. Last time it happened I noticed I could select 1st after turning engine off but I feel a slight pull when I dip the clutch.
Can you advise me as to what could be the problem? Thanks
Hey Danny, I'm about to throw an RXT into my 2003 Cobra. Should I resurface/re-use the factory flywheel or just get a new one with the clutch kit? Thanks! 🙏🏿
I would go with all new parts, but if your flywheel is in very good shape maybe it could be resurfaced. The cobra has an aluminum one and all the kits I see for the mcloud show a steel one. If the kit is new verify it doesn’t come with a flywheel (I see them as a package all the time).
How you doing my brother can you use white lithium grease
It needs to be high temperate so verify it is
Hi Danny, is it necessary to replace the fork? Going to replace the clutch in my 03 gt soon and was wondering if I should replace it....
It should be ok if the fork clamps onto the pivot ball tightly. If it falls off easy it’s time for a new one
@@dannyjohnsonsgarage i think I'll replace the pivot stud while I'm in there though. Its got 164k on it.
Burnish tungsten disulfide dry lubricant into all those mating surfaces, then grease.
I bought the red high temp grease is that okay to use?
I’ve use it as well and being high temp I think it’s fine
The problem with wet moly lube is that when the clutch disk material sheds off, it's fine pieces of metal that will be accumulating on the moly lube which in the end will crust up the lube. When the clutch disk material turns the moly lube all crusty, it'll be moly-clutch metal lube which squeaks and squeals.
There are dry lube spray with Teflon or PTFE from WD40 and DuPont that may work as well but I don’t know how long it would stay.
But the nice thing is that it resist dirt, dust and oil build up.
But 2-3 coats of it should be good.
Radel radel so here I am
I got a new skf bearing but it does not have the peak shape is perfectly round would it still work
If it’s designed for the car I’m sure it still will. It’s probably a Ford thing
@@dannyjohnsonsgarage thank you so much for your reply love the channel you are the best keep up the good work
My clutch makes a funny 'phmmph' noise when reverse is riden a little, and also when coasting in gear and releasing the clutch gradually. Doesn't seem to do it when shifting up and accelerating. Any ideas? Sounds like a squeeking big metal gate for a 1/4 second. In neutral when engine running, no noises. 🤔 vid of noise below....
ruclips.net/user/shortsEUoQARr_FdU?si=SluTpT3pe43opbQB
Backyard mechanics 😂