Did you fix your car issues? Let us know in the comments below, and maybe you can help someone else with a bad crankshaft position sensor! Don't forget to like the video and subscribe to our channel! More CPS sensor information: mechanicbase.com/engine/crankshaft-position-sensor-symptoms/ Website: mechanicbase.com/
I need help please. I've tried 3 different sensors and even tried another dme on my 2007 e60. I can't get any voltage drop on sensor running magnet across it.
Thank you so much for this very helpful and informative video! We have a 2013 Equus and it's giving us the exact problems you described in this video. By being your video, it's letting my husband know he's on the right track, and confirming his suspicion of what's going on with the car. Thank you so much for this helpful video!
Brother man thank you so much out of all the videos you broke down how was supposed to be broken down, very informative and straight to the point in detail💯💯🙏🏾🙏🏾
When the crankshaft sensor starts to go bad, it starts showing symptoms when it's cold. This is my own experience. You just can't find that information anywhere. You could easily think that there is a problem with the mixture ratio, although the crankshaft sensor may be the real culprit and may work well in warm weather, but at a certain degree of frost it starts to show symptoms.
@@buckhayes2104 And the freezing point where the symptoms start can be very sharp. It may be that the car works well, for example, at -13 c degrees and -14 c doesn't work anymore very well. In severe frosts, it sounded as if the ignition was completely out of place and the car would only idle at about 500rpm and engine may not be able to take more revs.. The car smoked a lot and the exhaust smelled strange.
@@buckhayes2104 Here's a link to a video where you can hear how the car's engine was doing before the fault was found. I myself had two faults. The crankshaft sensor and then the air mass meter. But the crank sensor was the main culprit. The faulty air mass meter made jerks only at higher revs while driving. But didn't affect the idle and didn't make it difficult.
GREAT VIDEO BRO. After winter my batterie in my S2000 died, I replaced it and the car started, but it didnt run smooth. The power was low, revs fell off and missfiring started and it cut out. I thought that was probably the Ignition coils. Replaced them and the car ran better but vibrations were getting higher the warmer the engine got. Then I got a tool to read the fault and it said Crankshaft position sensor. I erased it, it wont start anymore but now i definetly know why. It all makes sense after watching your video. I really appreciate your Content
Big thumbs up for mentioning some manufacturers put it on timing belt side. Unfortunately, my Civic is on timing belt side so it was big bucks to replace 😢
Thank you 🙏. This is the best explained video, I have every seen anyone put on here..... You mentioned every detail that my car is doing and when it's doing..... (Thank You) Plz.. don't change we need a guy like you to help us all...
Thanks, I have a ml350, 4mactic, 2011 , try to do , dc , inspection and my engine light is on and the 7:127:12 smog pump wasn’t bad so , intake camshaft cylinder the 2 on top will be replaced to see if this help my engine light to go off, the relay switch I’m going to change ! Hope you can give me some quick advice !
My problem is a P060A On my 2008 civic ,I think it’s more of a computer internal memory , BUT you ARE very good at explaining that particular sensor . Sounds like an honest guy
@@louwscustomsza I'm having same problem. Mine just cranks. I've changed the vvt solenoid, solenoid filter, camshaft sensor, fuel pump, starter, battery, a couple sparks plug... It's still cranks but no start. I have no codes showing when I plug the OBD. I'm thinking it's the crankshaft sensor tho.
@chriskramp5174 My problem was the metal plate that came after the crank sprocket. Apparently, the letter on it is supposed to be faced outside(B)(F). The crank sensor gets its reading from it
Thanks for sharing these great videos! I'm trying to find the location of the Crankshaft Position Sensor for the 2011 Benz B200 and wondering if you can help. Thank you!
Thank you for confirming the symptoms. Seems manufacturers can pump any random fault code out and they don't mean the same thing from car to car. Seems P1337 on Citroen DS3 does point to crankshaft position sensor. Getting to it though is somewhat of a challenge and I don't seem to be able to find anything that suggests correctly where it is.
I just replaced all 3 on my nissan xterra a year ago, and I have a code p0335 pop up now, do I have to replace all 3 again or just the crankshaft sensor? Thanks
Good information about the starting symptoms that I haven't seen elsewhere. My 2007 Chrysler T&C had trouble starting hot two or three times. I assumed the starter was going. There were no codes. Then today it threw a P0017 and started running bad - almost stalling out every time I came to a stop and responding slowly to the accelerator pedal. Will check the sensor tomorrow, but it seems quite likely. So I'm guessing the starting hot issues can be an early warning.
On very rare occasion my panel lights all come and the car will stall , it then starts up as normal ,sometimes it get a No Crank issue and sometimes Cut out after Starting up Car is CLK 220 CDI 2007 with 250000 miles on the Clock other wise all good Best Regards John
I have one question I cant fix w203 c200cdi I have no power to fuel pump Ive tested relay and fuse in the trunk everything is ok. My friend told me maybe crankshaft sensor is faulty and that can cause ecu to shut down power to fuel pump
Hi mr. Sam! I've a Opel Corsa C 1.4 16v the engine start good, any codes or ligths on the dashbord appers, but after 15 or 20 minutes after the start and when the engine get temperature 90°c the engine cut out, after that, I trying to restart it, but the half of the dashbord is off... no check engine light, no oil, no inmo, nothing light are ON... after that 1 hour and when the engine is cold or warm, the engine start again normally. Do you think that the sensor is damaged or the connector o wires? Thanks for your comments back. Regards!
Hi there mechanic base,i have a vw passat b6,saloon ,1.9 Tdi ,2007 and since a week dont start. On the tester showed me the camshaft sensor.Can be this problem to no start? If yes where is the sensor located? Thanks and waiting for your reply
I drive a chevrolet camaro v6 Lt 2010 I'm not sure where my crankshaft position sensor would be located?not sure what tools I would need to do the job myself simple rachet etc.
I guess I'm going thru the same issue from what 3 mobile mechanics told me what else can It be preventing it to start I was in middle of grocery shopping dropped meat off at home went to finish shopping it haven't started in 6 months I need help bad
Sir, great video, but I need your help on where my Crankshaft position sensor on my 2017 toyota camry le gas, One mechanic said it was at my right hand side located front tire where the cover is. Can you please help. Larry Chicago
Hi can you please advise position of Crankshaft sensor in a 2005/6 Ford Fiesta Trend 1600 manual petrol 3 door As well as a Volvo C30 T5 R-Design automatic 2012 Will really appreciate
Can this information be applied to motorcycles as well? My kawasaki z900 - 2017 sometimes just wont start and I've gotten the code P0335 on it. Sometimes it just wont start for at least 6-7 tries but then it works just great. However, after riding it for some time , if I turn of the ignition it wont start which has left me stranded a couple of times (sorry for my english, I'm from Sweden) Great informative video btw!
My 2017 Nissan patrol super safari starts rough making weird sound, fuel efficiency is lower than the norm, RPM plays around at idle, has no check engine light on (bought it used, suspect foul play). Used my scan tool and got a confirmed P0335 engine speed sensor which I assume is the same as crankshaft position sensor. Cleared it and and it still came back the same. Not sure where the crankshaft sensor is to inspect it, and the manual doesn't mention it. Its worth mentioning I also have a confirmed C1130 (ABS system code).
Thanks for the informative video! Vehicle: 2013 Hyundai, Azera. I am told this part needs to be replaced. There were numerous codes that presented w/ the main key fob. After I asked, should you check the communication w/ the other key fob (extra), they check and said that there was a "hidden code." The other key fob registered a code for this. It does not sound for sure that this is the fix, but they said it could clean many of the other codes. Do you think I should have to pay for a 2nd diagnostic hour when they should have initially asked if there were 2 key fobs? I've kept the car up and have never had any prior issues. Welcome your feedback.
Porsche Cayenne GTS - Along with Crankshaft sensor my electrical devices are not working or affected could this also be cos of crankshaft? Or is it something else? The driver seat window is slow and the roof doesn't close completely - There is a small gap and the LCD system bought last year also failed or not working.
so i did get the p0335 code and my car has been stalking or stopping on me and even check engine comes and go . so they say it’s the crankshaft sensor. u guess my question is how do you know if it’s the front or back crankshaft sensor . i have a 2014 hyundai sonata @mechanicbase
My car has a tsi 2.0 petrol engine, basically a golf GTi engine. Drives great, but sometimes when it's warmed up, it will struggle to start, and it will the start when I let it cool down? Is it this sensor I need to change?
hyundai accent limited 2020. car vibrates sometimes if im on a red light. starts fine, code says cold start cam shaft sensor. do i need to replace it then?
Can't see anything from above ? Should I be able to see it from looking down from under the bonnet/Hood or do I need to get under the car to actually locate it ? Car is 2017 Mokka X 1.6 petrol
I have 1989 MK1 VW Golf GTI Convertible with a DX type of engine, can you assist by giving me instructions where to locate it. Please attach a picture of it. Thanks, Costas.
Ugh..i have a code for the crankshaft sensor..time to order it and get it done.. thank you for the informative video..i have to get in the mindset to work on my vehicles..
Did you fix your car issues? Let us know in the comments below, and maybe you can help someone else with a bad crankshaft position sensor!
Don't forget to like the video and subscribe to our channel!
More CPS sensor information: mechanicbase.com/engine/crankshaft-position-sensor-symptoms/
Website: mechanicbase.com/
Can't find my crankshaft position sensor in my v70 2.5t volvo
I need help please. I've tried 3 different sensors and even tried another dme on my 2007 e60.
I can't get any voltage drop on sensor running magnet across it.
1:32
Hello name Joey I like to know where would my crank shaft position be at I have a 2007 buick lucerne cxl v6 engine
Is this a pcv vale
Thank you so much for this very helpful and informative video! We have a 2013 Equus and it's giving us the exact problems you described in this video. By being your video, it's letting my husband know he's on the right track, and confirming his suspicion of what's going on with the car. Thank you so much for this helpful video!
same happend to me, but never seen the camshaft sensor error, only random missfires errors.
Brother man thank you so much out of all the videos you broke down how was supposed to be broken down, very informative and straight to the point in detail💯💯🙏🏾🙏🏾
When the crankshaft sensor starts to go bad, it starts showing symptoms when it's cold. This is my own experience. You just can't find that information anywhere. You could easily think that there is a problem with the mixture ratio, although the crankshaft sensor may be the real culprit and may work well in warm weather, but at a certain degree of frost it starts to show symptoms.
Tell me more.
@@gottahavegoalsset ?
This explains my frustrations OMG!! This is very important information .
@@buckhayes2104 And the freezing point where the symptoms start can be very sharp. It may be that the car works well, for example, at -13 c degrees and -14 c doesn't work anymore very well. In severe frosts, it sounded as if the ignition was completely out of place and the car would only idle at about 500rpm and engine may not be able to take more revs.. The car smoked a lot and the exhaust smelled strange.
@@buckhayes2104 Here's a link to a video where you can hear how the car's engine was doing before the fault was found. I myself had two faults. The crankshaft sensor and then the air mass meter. But the crank sensor was the main culprit. The faulty air mass meter made jerks only at higher revs while driving. But didn't affect the idle and didn't make it difficult.
Informative, no bs. It was nice knowing what tools I would need. Well done.
Thank you; this helped me to figure out that my sensor is bad
I almost replaced the ECM when it was just sludge and metal buildup on the CPS. Thanks you just saved me a couple hundred dollars.
Glad to hear that👍
If you had metal build up in your crank sensor you have other issues asswell
Was there no error code?
Hey mine was dirty do I clean the sensor with brake cleaner and the slot as well where the sensor goes ? Or just the sensor?? Please help
@@vladt6038hey how do I clean it ? Like do I clean the slot where the sensor goes as well with brake cleaner or JUST the sensor?
GREAT VIDEO BRO. After winter my batterie in my S2000 died, I replaced it and the car started, but it didnt run smooth. The power was low, revs fell off and missfiring started and it cut out. I thought that was probably the Ignition coils. Replaced them and the car ran better but vibrations were getting higher the warmer the engine got. Then I got a tool to read the fault and it said Crankshaft position sensor. I erased it, it wont start anymore but now i definetly know why. It all makes sense after watching your video. I really appreciate your Content
🫡🫡
I thank you for describing the symptoms so detailed, as I have exactly the named problems. Thank you!
Same!
Big thumbs up for mentioning some manufacturers put it on timing belt side. Unfortunately, my Civic is on timing belt side so it was big bucks to replace 😢
Thank you 🙏. This is the best explained video, I have every seen anyone put on here..... You mentioned every detail that my car is doing and when it's doing..... (Thank You) Plz.. don't change we need a guy like you to help us all...
Thanks for your clear explanation, i have an mercedes R350 and i have the same symptoms. I`ll look it.
Thank you great video! Very helpful! I got the same issue when the engine is warm.
Yes, that could be the crank sensor. Do you have any codes?
Thanks, I have a ml350, 4mactic, 2011 , try to do , dc , inspection and my engine light is on and the 7:12 7:12 smog pump wasn’t bad so , intake camshaft cylinder the 2 on top will be replaced to see if this help my engine light to go off, the relay switch I’m going to change ! Hope you can give me some quick advice !
My problem is a P060A
On my 2008 civic ,I think it’s more of a computer internal memory ,
BUT you ARE very good at explaining that particular sensor .
Sounds like an honest guy
on my Toyota Corolla it's the VVT soliniod, but same symptoms , great explanation in the video
Did it cut off fuel and spark? My corolla won't start just cranks. It cut off fuel and spark
@@louwscustomsza I'm having same problem. Mine just cranks. I've changed the vvt solenoid, solenoid filter, camshaft sensor, fuel pump, starter, battery, a couple sparks plug... It's still cranks but no start. I have no codes showing when I plug the OBD. I'm thinking it's the crankshaft sensor tho.
@chriskramp5174 My problem was the metal plate that came after the crank sprocket. Apparently, the letter on it is supposed to be faced outside(B)(F). The crank sensor gets its reading from it
Thanks for sharing these great videos! I'm trying to find the location of the Crankshaft Position Sensor for the 2011 Benz B200 and wondering if you can help. Thank you!
Thank you this is exactly what’s been going on
Perfect video.. I fixed it. Great work.
Thank you for confirming the symptoms. Seems manufacturers can pump any random fault code out and they don't mean the same thing from car to car. Seems P1337 on Citroen DS3 does point to crankshaft position sensor. Getting to it though is somewhat of a challenge and I don't seem to be able to find anything that suggests correctly where it is.
Thank you boss, ur symptoms are same as mine, I think the sensor is broken. Engine switches itself off once warmed up
I have a 2015 Nissan Altima where is my camshaft sensor or crank sensor located thank you so much for your helpful video.
2.5 engine? If yes, it should be near the transmission end, on the back of the engine (facing the firewall).
Very informative video Sir. Thanks for the knowledge too.
I just replaced all 3 on my nissan xterra a year ago, and I have a code p0335 pop up now, do I have to replace all 3 again or just the crankshaft sensor? Thanks
Great video! I was looking for one on 05 Chrysler Pacifica I have not found yet can you help?
Kan det bli trykk på motor med dårlig sensor?
Good information about the starting symptoms that I haven't seen elsewhere. My 2007 Chrysler T&C had trouble starting hot two or three times. I assumed the starter was going. There were no codes. Then today it threw a P0017 and started running bad - almost stalling out every time I came to a stop and responding slowly to the accelerator pedal. Will check the sensor tomorrow, but it seems quite likely. So I'm guessing the starting hot issues can be an early warning.
On very rare occasion my panel lights all come and the car will stall , it then starts up as normal ,sometimes it get a No Crank issue and sometimes Cut out after Starting up
Car is CLK 220 CDI 2007 with 250000 miles on the Clock other wise all good
Best Regards
John
Thank you. Sounds like every big part of the engine has a sensor!
Just want to know can you swap the magnetic crankshaft sensor to a hall affect sensor
I have a 1996 Ford explore and I can't find the crankshaft senor bank 1 tank's for your help
Hey so I'm having trouble finding the crankshaft sensor on my 2010 GMC terrain sle 3.0l AWD can you possibly help by chance ?
I am looking for the crank position sensor for a 1996 Nissan quest GXE with the 3.0 V6
I have one question
I cant fix w203 c200cdi
I have no power to fuel pump
Ive tested relay and fuse in the trunk everything is ok. My friend told me maybe crankshaft sensor is faulty and that can cause ecu to shut down power to fuel pump
Thank you man makes so much sense now
Hi mr. Sam!
I've a Opel Corsa C 1.4 16v
the engine start good, any codes or ligths on the dashbord appers, but after 15 or 20 minutes after the start and when the engine get temperature 90°c the engine cut out, after that, I trying to restart it, but the half of the dashbord is off... no check engine light, no oil, no inmo, nothing light are ON... after that 1 hour and when the engine is cold or warm, the engine start again normally. Do you think that the sensor is damaged or the connector o wires?
Thanks for your comments back.
Regards!
That could definitely be the crank sensor.
Can you tell
Me the cranckshaft position sensor lovation on volvo S90 2017 diesel saloon
Looking for location of the crankshaft sensor in my 2005 Dodge Caravan. Do you know of a drawing online for the location?
Got a hilux 1kd engine. Put in a new engine,but it not starting can error codes be causing it from reading the new engine?
Hi there mechanic base,i have a vw passat b6,saloon ,1.9 Tdi ,2007 and since a week dont start. On the tester showed me the camshaft sensor.Can be this problem to no start? If yes where is the sensor located? Thanks and waiting for your reply
Very informative, thank you!
I drive a chevrolet camaro v6 Lt 2010 I'm not sure where my crankshaft position sensor would be located?not sure what tools I would need to do the job myself simple rachet etc.
Where can I find the crankshaft sensor for my Nissan Sunny 2022?
I guess I'm going thru the same issue from what 3 mobile mechanics told me what else can It be preventing it to start I was in middle of grocery shopping dropped meat off at home went to finish shopping it haven't started in 6 months I need help bad
Sir, great video, but I need your help on where my Crankshaft position sensor on my 2017 toyota camry le gas, One mechanic said it was at my right hand side located front tire where the cover is. Can you please help. Larry Chicago
Hi can you please advise position of Crankshaft sensor in a
2005/6 Ford Fiesta Trend 1600 manual petrol 3 door
As well as a
Volvo C30 T5 R-Design automatic 2012
Will really appreciate
I have a 1996 Ford explorer V8 where would the crank sensor be located at
Can this information be applied to motorcycles as well? My kawasaki z900 - 2017 sometimes just wont start and I've gotten the code P0335 on it. Sometimes it just wont start for at least 6-7 tries but then it works just great. However, after riding it for some time , if I turn of the ignition it wont start which has left me stranded a couple of times (sorry for my english, I'm from Sweden) Great informative video btw!
Yes, it's quite likely. That sounds like a crank sensor.
If the sensor is bad, will you have a problem with idle up high when your feet is barely on the gas. 2010 Cadillac srx
My 2017 Nissan patrol super safari starts rough making weird sound, fuel efficiency is lower than the norm, RPM plays around at idle, has no check engine light on (bought it used, suspect foul play). Used my scan tool and got a confirmed P0335 engine speed sensor which I assume is the same as crankshaft position sensor. Cleared it and and it still came back the same. Not sure where the crankshaft sensor is to inspect it, and the manual doesn't mention it.
Its worth mentioning I also have a confirmed C1130 (ABS system code).
All those symptoms correspond to a bad CKP sensor.
Golf Mk5 gt170 BMN is the sensor on belt or in oil filter housing ?
Where is it located on a 1999 dodge van
I have a Opel Combo 1.7 di 2002 car, it only starts in the morning and during the day it doesn't start, could this sensor be the problem?
Where can I find it on Hyundai Sonata 2013 ?
Thank you
06 cobalt where is the crankshaft and camshaft sensors located
Where is the crankshaft sensor located for a 2015 chevy equinox? Please and thank u
How to find the crankshaft position sensor in the Honda Civic 2012LX? Where is the location?
06 Chevy cobalt where is the cam shaft and crank shaft position Sensors located
Can it cause hard starts when the car is up to temp
Thanks for the video I have a 2007 chevy tahoe 5.3 can u help me locate the sensor thanks
It's on the back side of the engine, near the transmission, on the passanger side.
Just look for the oil cooler lines, and you should spot it.
Where is crankshaft position sensor for 2012 ford taurus sho 3.5 ecoboost
This video was very valuable & informative Thank You 👏
Where is the crankshaft position sensor located on a 2014 Audi Q5? Thank you, Marcus
Thanks for the informative video!
Vehicle: 2013 Hyundai, Azera. I am told this part needs to be replaced. There were numerous codes that presented w/ the main key fob. After I asked, should you check the communication w/ the other key fob (extra), they check and said that there was a "hidden code." The other key fob registered a code for this. It does not sound for sure that this is the fix, but they said it could clean many of the other codes. Do you think I should have to pay for a 2nd diagnostic hour when they should have initially asked if there were 2 key fobs? I've kept the car up and have never had any prior issues. Welcome your feedback.
Hello sir how can I locate the crankshaft position sensor in toyota corolla 2003
Which engine?
Is it best to change the crankshaft and camshaft position sensors at the same time?
NO
Was very informative thank you
Where can I find it for Nissan Pathfinder 2010
Where will I find it on my 2000 gmc sonoma 4.3 vortex
Where do you find the crank sensor for opel corsa lite 1.4 thanks you
Which year is your car? How many HP?
I have oil in the connections at the female end and male end. What do I do?
Hello. Where would this be located on a 2010 Suzuki Kizashi?
Which engine do you have?
Hello, thanks for this. Can you please share where the position of the crankshaft is on Renault Kangoo 2003 Automatic transmission? Best
Hi. Which engine?
@@MechanicBase 1.6 16V (95 Hp) Automatic
If the crankshaft sensor is bad can it affect the fuel pump
No. But the injectors won't give fuel if there is no signal from the crank position sensor.
We're is the cam shaft senior on a 2000 QX4 invinjty
You could most likely find it on google for the user manual
1996 toyata granvia 3ltturbo I can't find sensor any help?
Porsche Cayenne GTS - Along with Crankshaft sensor my electrical devices are not working or affected could this also be cos of crankshaft? Or is it something else?
The driver seat window is slow and the roof doesn't close completely - There is a small gap and the LCD system bought last year also failed or not working.
I have a 2010 lexus es 350 code p0335 can't find the location of the crankshaft position sensor 4:58
Hi, I am trying to find the location of the crankshaft sensor on a bmw f15 530d n57t thanks
so i did get the p0335 code and my car has been stalking or stopping on me and even check engine comes and go . so they say it’s the crankshaft sensor.
u guess my question is how do you know if it’s the front or back crankshaft sensor . i have a 2014 hyundai sonata @mechanicbase
Where do you find a crank shaft fencer on a mini 2021
My car has a tsi 2.0 petrol engine, basically a golf GTi engine. Drives great, but sometimes when it's warmed up, it will struggle to start, and it will the start when I let it cool down? Is it this sensor I need to change?
What about a 2005 Chevy equinox, where is it located
It should be at the back side of the engine, near the RH driveshaft.
hyundai accent limited 2020. car vibrates sometimes if im on a red light. starts fine, code says cold start cam shaft sensor. do i need to replace it then?
Which exact code do you have?
Not sure if I have one w124 230e not getting the vehicle started
Trying to fix a 2013 hyundai genesis 3.8 need to locate the crankshaft sensor
Great advice.
Where to find Crankshaft position sensor chevy captiva sport 2013 v4. Thank you. It feels low power? Great inf.
Have a VW T4 Cavalry Van. Were is the crank shaft sensor positioned in the Engine. As what you explained in your Video, is my Van.
Hey, which engine do you have?
I like your random hand signals 🤣
👇👈🫰👇🤌😁😁
@@MechanicBase 🤣👍
Dear friend,my vehicle is 2020 Mazda bt50. It suddenly hard starts right after the fuel filter was replaced
Thanks.where is the crankshaft position sensor connector in a 2005 isuzu 4jh1 truck?
Toyota rav 4 2007 gas 4x4 2.0. Where do i find the crankshaftsensor?
Whwre is it located on Pontiac grand am 04
Can you tell me please where to find crank shaft position sensor on a 2017 Vauxhall mokka x 1.6 petrol.
I have searched but cannot find
It should be under the oil filter.
Can't see anything from above ?
Should I be able to see it from looking down from under the bonnet/Hood or do I need to get under the car to actually locate it ?
Car is 2017 Mokka X 1.6 petrol
I have 1989 MK1 VW Golf GTI Convertible with a DX type of engine, can you assist by giving me instructions where to locate it. Please attach a picture of it. Thanks, Costas.
Do you know where the crankshaft sensor may be on a Lexus 07 is350
Pozdrav. Mozete li mi reci gde se nalazi na VW Touran 1.4 TSI, 2007. god.?
Can these give problems without fault codes?..
Thanks for details from Oamaru New Zealand.
Yes, on some cars.
Ugh..i have a code for the crankshaft sensor..time to order it and get it done.. thank you for the informative video..i have to get in the mindset to work on my vehicles..
🫡
Great video thank u sit