2004 Honda Civic Clutch Replacement [Full Tutorial]
HTML-код
- Опубликовано: 4 июн 2018
- In this video, learn how to replace the clutch and flywheel on a 7th gen Honda Civic EX (2001, 2002, 2003, 2004, 2005). Many other Honda's will be similar to this install, especially any other D series engine from older Civic models. This install is actually pretty straight forward and not all that bad (hardest part is getting the tranny and motor to line up correctly). But it is a really big, pretty involved install that took me and a friend 14 hours to complete. I wouldn’t try this one unless you’re mechanically inclined, but if you are, it’s well worth the knowledge gained and amount of money saved! Hope you found it helpful and don’t forget to comment, like, share and subscribe! Thanks for watching!
Parts needed:
Exedy KHC08 OEM clutch kit - amzn.to/2LDpEYm
Exedy FWHDC02FF flywheel - amzn.to/2JaMVT8
“Blue” thread locker - amzn.to/2L2dWWk
2 qts Honda genuine manual tranny fluid - amzn.to/2xpGkjb
Shift fork spring - Honda part number - 22835-P7N-000
2 shift linkage cotter pins - Honda part number - 94201-20220
Tools needed (out of the ordinary stuff):
You need to have 12pt sockets for pressure plate (10mm) and flywheel bolts (17mm) - amzn.to/2LFaRwc
Swivel sockets help big time! - amzn.to/2kvVaLs
Pry bar - amzn.to/2JeoFiY
32mm deep socket for axle nuts - amzn.to/2LE6gdO
22mm socket for strut nut - amzn.to/2JiwNiJ
27mm deep socket to remove reverse light sensor - amzn.to/2JeHvGB
Motor mounts that also need to be removed to drop the tranny (RUclips links):
Front motor mount - • Tutorial: Change 2004...
Transmission side motor mount - • 2004 Honda Civic Trans...
Rear motor mount - • 2004 Honda Civic Rear ...
How to change manual tranny fluid on 2004 Honda Civic - • Tutorial: How to chang...
Quick cheat sheet I made to remember the order of removing parts:
Part 1 - while car is on the ground
Remove battery
Remove air box
Move all the wires that get in the way of the starter and that area
Remove 2 sensor plugs (reverse light and speed sensor)
Remove starter
Remove shift linkage
Remove slave cylinder hard line
Part 2 - After you put the car on jack stands
Drain tranny fluid
Take axles out
Remove motor mounts, rear mount first (and also front mount and tranny side mount)
Remove bottom tranny bolts (2 tranny bolts, 4 engine stiffener bolts, 1 more tranny bolt near the axle input area plus 2 flywheel cover bolts)
Remove other 4 bell housing bolts
Drop tranny
🔋 🔋 🔋 In the market for a Tesla car or solar? Get credits for swag, supercharging miles and other goodies! Please use my referral link - ts.la/darrell70425 🔌 🔌 🔌
===============================================================================
Hello! My name is Darrell. I'm just a regular guy who likes editing and uploading videos to RUclips! I really like teaching people how to do any and everything I have experience doing. In addition, I do product reviews and travel documentaries when the opportunity arises. So if you're interested in any of these things, welcome!
Don’t forget to comment, like, share and subscribe! Thanks for watching!
ruclips.net/user/nukem384...
If you're interested in tech news, come on over to my news channel!
/ @nukem384news9
My simple recording setup. Get these products on Amazon! By buying products thru my links, I'll earn a small commission that helps keep my videos coming! Buying thru my links doesn't cost you a cent more! Thank you very much for your support!
Gopro Hero 5 Black
amzn.to/2ssiS23
PoP Voice Lav Mic
amzn.to/2GkmzMW
Outro Music - NCS - Say Good Night - Joakim Karud
Find me on social media!
Instagram: / nukem384
Twitter: / nukem384
Twitch: / nukem384
Facebook: / nukem384
Blog: nukem384.blogspot.com/
honda civic (automobile model),how to,honda civic,honda clutch,how to install a clutch,clutch disk,pressure plate,flywheel,civic,honda,2001,2002,2003,2004,2005,release bearing,pilot bearing,bearing,clutch,engine, clutch,flywheel,honda civic (automobile model),d17 a2 flywheel pressure plate and clutch,d17 a flywheel pressure plate and clutch,2001 honda civic ex 5 speed manual review,honda civic clutch rep, honda,civic,honda civic,2002,2003,2004,2005,manual transmission,input shaft bearing,isb,clutch replacement,flywheel resurfacing,transmission removal,flywheel,clutch,clutch throw-out bearing,throw-out bearing, honda,how-to,do-it-yourself,honda civic,replace clutch and flywheel,replace clutch,replace flywheel, b18 transmission removal,how to swap a honda civic transmission ,clutch replacement,integra clutch 
Авто/Мото
Aug 24 2023 1 of the best tutorial, no time wasting, clear speaking, no background noise, proper light and imaging stable, great thank you!!!!
Appreciate it! Thanks!
excellent work! Concise, thorough, clear talk, good vocal mic work, and no rambling. Finally! thank you!
No problem! Glad it was useful!
DUDE! You seriously kick ass for making this! Also i must say, well done on how informative this is!
Great video
I can really appreciate all of the information you put in the description.
Thank you.
glad it helped! good luck if youre doing the install soon!
Seriously awesome tutorial. Too many crappy ones out there! My 04 hit 134000 miles today and the clutch is on her way out, so I'm really glad I found this now to guide me through the process. Thanks for taking the time to document this!
no problem! good luck on the install and hope it goes as smooth as mine did!
Lol my 05 is at 132000 and the clutch is just dead😂
@@brentparsons2661 lol! better buy some parts and follow the tutorial :P
@@nukem384 How would I know if it's the clutch and not the tranny? Had a shop tell me $1200 to do the tranny change, but another wanted to just change the clutch... problem I have is that I can't shift it (manual) into 1st gear. I can put it into 1st and go. Actually, now that it's sat in the woods for the last 1.5 years all gear shifting is very difficult (feels rusty).
Figure I'd change the clutch and see if that does the trick. What do you think?
@@RichardTurlington The engine/tranny in your car is quite different as you have a K24A and mine is a D17A. Basically, your engine is put in the reverse way compared to mine. With the symptoms you're giving me, it sounds like your tranny is the problem. The actual gears could be worn out or arent meshing together correctly. One thing you could try is changing your tranny fluid, but usually that'll just mask the problem for a while and it'll come back. Changing the clutch probably isn't going to fix your problem unfortunately :(
Unreal how much detail you crammed into a 14 minute video, this is a fairly long job overall but you touched on everything. Great video, keep up the good work.
Thanks!
Freaking excellent video. Straight up and down start to finish was usefull info and nothing else! You need mor subscribers for sure dude!
Thanks so much! Appreciate it
This just got me through my clutch job on my civic. Thank you so much!!!!
Glad it helped!
Thank you so much for making this video. Very helpful and well made. God Bless!
Thanks! Glad it helped!
I am damn scared doing this! I appreciate your efforts but I need the courage you had.
It's not an easy install, let's put it that way. I wouldn't try it if you feel in over your head. Might be better to take it somewhere in that case.
I like the video myself.its clear and clean.
Great video, thanks for making this! I'm about to 'hand down' my 160k 2003 Civic daily driver to my son. Clutch & struts will be his introduction to fixing his own car, and I needed the refresher :-)
That's one big introduction to cars! Brake pads I would say would be a good intro haha. Throwing him in the deep end lol. Good luck, hope the install goes well for you guys!
@@nukem384 He's done brakes and oil changes on other vehicles, but has never worked on "his" car (he's 15, about to be 16). I feel like this will give him the confidence to tackle most any car issue he has in the future :-)
@@truthsmiles Totally, for sure. If you guys can successfully do this, yeah, he should be able to handle quite a bit of stuff. That's how I learned, many years of doing all sorts of different installs. Too bad I didn't film the timing belt when I did it on this car. Next time!
@@nukem384 I was a mechanic a million years ago so nothing scares me, but I'm also smart enough to know that I don't know everything & I benefit a huge amount from watching someone else do it first, so your video is pure gold. Thanks again :-)
I did the timing belt on mine at 125k a couple years ago. Stripped the tensioner bolt so had to re-tap and heli-coil, but all that was available was SAE fittings haha so now there's one weird bolt in the engine.
Perfect video for someone that's worked on cars just not this specific one. 👍
Awesome video Darrell! 🙂
Thanks! Awesome name BTW :D
Thanks man!!! This helped me big time!
No problem! Glad it helped!
Great video! For 3 days, my car is in a mechanic, and we can not find where is located oil pressure sensor. Is it possible? Honda Civic 1.7cdti 101hp . could you help me? Thanks
How similar would this be to removing a CRV 2004 transmission? Seems alot of the civic & CRV are similar.
Such a good video dude!
Thanks! Glad it was helpful! Now go get that clutch/fly!
Great video!
treydot_ thanks! Glad it was helpful!
Great work man tank you!
No problem! Glad it was helpful!
Para quitar la barra homocinetica de ese lado, hay que destornillar algo, o sale sin hacer fuerza?
I have a 2014 Civic and am getting my feet wet with car maintenance. Replacing the rear brake pads and a seized brake caliper was my proudest moment. I feel this job is for the professionals. It looks INSANELY difficult.
I'm definitely no professional mechanic, but almost 2 years later, I'm still driving this car with this clutch and it's been working perfectly. But it's not for newbies. You'd definitely want to have a good amount of car install experience to try this one, as there are quite a few things that could go wrong.
dank i need a friend... i always work alone on my car, but this need friend level~!
If you're doing this in your garage, you definitely need a friend. It's doable by yourself if you have a lift and can stand up, but not when laying down.
@@nukem384 i still have most my tools, but looking for a friend here in USA, is very hard.
Excellent video brah. 👌🏼
Nice you the man!
Thanks! Glad it was helpful!
Thank you
Glad it helped
What do you do if the trans isn’t going all the way back into the engine??? Need help it’s about 2-3 inches from sitting flush on the engine could it not be getting all the way to the flywheel????
You just have to keep trying. This is the hardest part of the install. It took us about 45 mins to wiggling, shifting, etc to get it back into the motor flush. Just try every angle and make sure the tranny is lined up straight with the motor. It's eventually line up and go in. Don't try and force them together with the bolts as I mentioned, so your engine and/or tranny will be toast!
...MY MAN!!! Thx dude
no problem! good luck if you're doing the install soon!
@@nukem384 .how much that clutch kid cost you.? Was it Exedy clutch that you used?
@@declanosbourne62 link in description for the part. Yeah, OEM Exedy clutch
I like how careful he is most mechanics just tug and blast all the bolts on with a impact
Thanks! I've had plenty of nightmares about stripped threads and bolts, so I try not to ever let that happen anymore.
is it possible to replace the rear main seal for the amount of room given between the engine and trans? thanks.
Yes. It's actually good practice to change that out while you're doing the clutch/flywheel. Mine was ok, so I didn't bother. But we could've done it on this install, no problem.
Great job 👍 Thanks a lot for the video. Do you know if this works the same on the 1.3L hybrid civic of the same model year?
Thanks! I would suspect not because it's a hybrid. The engine is going to be a totally different model, probably not a D series motor like this car. Probably better if you can find a tutorial for a Civic hybrid clutch. That'd probably be a lot more similar.
hey can you tell me where can i find the sevice mannual for the civic you have worked in this video
do a google search. there are multiple sites you can buy the honda service manual from. just make sure its the one actually produced by honda, not the helms or haynes manual. while those are good, the best manual is obviously going to be from the engineers that designed the car :)
hey i have an 04 civic with 157k just did the new cables w a new shifter box etc now im getting a clutch i want a stage 2 but dont know what brand i should buy
Not something I'm very knowledgeable about off the top of my head. My suggestion is put this question on a specific Honda or Civic forum. Those guys will definitely have some aftermarket/racer suggestions for you.
I start having problems with my A/C=Air it keep coming on and off I think it has some to do with the clutch any suggestions? Great video 👍
Changing your clutch isn't going to fix your AC. It could be your AC relay fuse. That's where I'd start with the symptoms you're telling me.
A great and well detailed explanation! Is this a single or dual mass flywheel ? Do you have any OEM number reference or aftermarket brand ? After 192k with 2004 Civic 1.6i EU EP l have to replace both flywheel and clutch kit, but l dont find the spare flywheel. Many thanks in advance!
Glad it helped! I believe it's a single mass flywheel. You can verify yourself, as all part numbers and links are in the description.
Can I take the trans completely out
What if I don't do the under the hood part? What will happen? Can I not just jack the car up and take Separate the transmission and put in a new clutch? My clutch is slipping and I can't afford a mechanic to do it. Please reply to me
Uhh...there's no way you're getting the tranny off without opening the hood. Simple as that. There's too many parts and things you need to disconnect under the hood to successfully complete this install.
My clutch is slipping and if i just listen to my cousin when he was telling me that since I'm working on the transmission,just change the clutch as well and now I'm going to do it also a guy at the dealership told me if I'm going to do my clutch i must change the rear main seal that behind the flywheel so now I'm going back in there, i will do the rear main seal.its $50 bucks at the dealership and i strongly recommend the dealership main seal because if its get bad in short time after you insall it , its a pain in the ass to go back there for one simple seal so use the genuine stuff.
Hey my flywheel doesn't have those two pins I bought a new one from autozone should I be concerned? The old one does have those two pins
It's not super critical, but those pins are used to line up the flywheel with the pressure plate. You're just going to have a harder time getting the two to line up. As I mentioned in the video, I would suggest you line them up before you put the flywheel on the motor, that way you don't have to try and figure out the alignment when you're under the car. The pressure plate will only go on one way, so aligning before you get under the car will be a lot easier.
Not necessary to remove brake calipers. You can use a C-clamp or Vise Grip pliers on Flywheel. Make sure shift fork doesn't pop off during reassembly.
Did you say prior to the video getting underway that you have to remove motor and trans mounts?
Not prior, but that's one of the steps to complete this install. There's a note in the middle of the video and I think I verbally mentioned when you should take the motor mounts off, and to refer to the description for the links to the motor mount tutorials
Do you have to remove ALL the motor mounts or would just the one on the transmission side work?
I mean, you can try and take short cuts. But I don't think that's going to end well, you'll probably end up wasting more time and end up taking them off anyway. You don't have to take the driver side mount off. You mighttttt be able to get away with leaving the front mount. The other 2, 100% you have to take off of the tranny isn't coming out.
Thanks
No problem!
If you're going to the trouble of replacing the clutch, highly recommend you do the throw out bearing on the trans at the same time. If it goes, no more shifting.
Pilot bearing is new and sits in the new flywheel
@@jeremyyoung7631 He said throw out (release)bearing not pilot bearing
I recommend changing the crank seal behind the flywheel, might as well while you're there. Ive seen them fail and piss oil all over the clutch.
Yeah might as well make it worthwhile since you're already there... That'd be like going through all the trouble of replacing the timing belt without replacing the water pump. 😅
Do you need any gasket maker when putting the tranny case back on?
No because theres no fluid on that side of the tranny thats mounting to the motor
I was glad to see that cinderblock was to place the caliper on. I was about to say, if that car comes down on that it is going to crumble.
Thanks so much! I have another brake job video where I use the cinder block for the caliper in the same way, but SO many people made rude comments assuming I'm using it like a jack stand, super annoying. Glad you noticed it wasn't supporting the car in this video!
Awesome
Glad it helped
Hi man, this is a great video! One question. My father have a Honda HR-V (2003, 4WD) with D16W5 (91kw) engine. I won' find any clutch removal/change video of that engine, maybe that engine/transmisson have seen on your video would be nearly same? (OK for the 4WD, there should be many differences, but i think some parts are totally have match.) We have to change the clutch, and the common hydraulics of that, every help would be greatful!
I would think since it's a D series engine, that getting to the tranny and getting it off would be similiar. Obviously you also have a driveshaft to connect the rear wheels, so that'll not be covered in my tutorial. You could probably use this as a template, but there will be differences since it's not exactly the same car or engine. Good luck!
Yes, my point of view you match of yours , that driveshaft would cause little trouble when we demount off the transmission, but if you say so, and this is the same the D series engine what i seen on your video, i think, this clutch change would be not as hard as i think first time. But we will see, i will report after it! Thanks!
How do you find out the torque specifications? BTW quality video bro!
best way is to have the service manual from honda. that will have torque spec for every bolt in your car. the torque specs i gave for the important bolts are from the service manual. good luck and thanks!
You can also buy a service manual from rock auto..i just got mine like 2 or 3 days ago from that website.they have the disk for service manual as well. It cost me about 20+ for the book but the disk will cost more.
How many miles were on your Civic clutch you did the replacement? What is it obvious the clutch was going out? I have a 2005 civic I bought used and now has 220k in the original clutch. Just was wondering if you did this based on mileage or symptoms
It had about 176K on it. I only drove about half that though cause I bought the car used. The previous owner wasn't good at driving stick cause I could tell right when I bought the car the clutch was really kind of messed up. Parts like the clutch and brakes are all based on usage, there's no set mileage when you need to change. So I changed it based on symptoms. It was really starting to slip and was becoming almost un drive able.
my 98 accord went 350k on the oem clutch. finally died from a cracked head due to a bad cooling system and overheating/blowing head gaskets in a very sneaky way. idk the civics are geared down a bit to be more zippy so i expect some extra clutch ware from that, especially the EX/vtec, but other than that and rotational mass considerations i would expect the clutch to last somewhere between 10k-400k miles purely depending on the driver and how much is hwy obviously. impossible to say.
I learned 1 thing, take it to da shop!!!!
Haha, yeah, it's not the easiest install. But I'm happy I saved a ton of cash! It wasn't all that bad for me.
Depends on your shop availability, speed in which you need it, ability. It's not hard but its intricate for sure and requires some knowledge.
What about the mounts do you remove them
You're talking about the engine mounts? Yes you do. I just didn't show them in this video because I have separate videos on all of them as linked in the description and there's a note during that piece of the video.
So i found a car online worth $500 - honda civic 2002. It needs a new clutch, rotor, and brake pads. Is it worth it to buy?
Up to you. I would def. have a mechanic do a car inspection on it. That old a car and they are already telling you it needs those things, there's probably more stuff wrong with it. And you didn't even mention mileage, which will be a big factor too for such an old car.
How many labor hours is this clutch replacement ?
All going to depend where you go. I believe a good mechanic can do this install in 8-10 hours. It took my DIY self and a friend 14 hours to do it.
thank u. sir.
No problem! Glad it was helpful!
Would you attempt this on an 2011 Acura TL with 6MT? Am I crazy for even thinking of trying it?
It all depends how handy and car savvy you are. And if you have a friend that can help. Doing a clutch in the garage on jacks is definitely a 2 person job. I wouldn't attempt it by yourself. That said, that engine on your car would be pretty different from mine. AWD or FWD? AWD would make it a lot more complicated, but it could still be done. If it were me personally, I'd probably pass on trying to do it on a V6 unless I had a ton of good resources and was able to see every bolt being taken off and where those locations were.
@@nukem384 yeah it's a V6 AWD. Your video got me motivated. Great help thank you!
@@supersabrosinho Yeah, AWD drivetrains are definitely more complicated with the driveshaft going to the back. On top of that, the tranny is going to be huge and way heavier than mine. I had a Subaru at one point (AWD too) and there's no way I'd attempt that one. But glad my video got you motivated and if you try, good luck! Hope you have good results!
dude i would just pay someone to do it. its gonna be difficult. sometimes the money you save isnt worth the headache.
Great video...
1 caveat...
NEVER. SUPPORT. THE. MOTOR. BY. THE. OIL PAN!!!
My replacement flywheel doesn’t have those two Rivets like the factory one.
That's fine. I answered somebody else in the comments about the same thing. It's just going to be harder to line up the flywheel and pressure plate. Make sure you have them lined up before you get under the car to change them out.
Is this for a 1.7L?
Yup. D17A2 in this video
Bro just bought a 2004 honda civic and I dont have really anything but a 64 piece tool set from Lowe's and youtube I'm trying to replace my flywheel. Is there any shirt cuts to take to get this done solo in a day
Errr don't want to sound like a debbie downer, but did you take a look at the description and how many other tools are needed besides a big socket wrench set? Honestly, I don't think it'd be possible with just that set considering how many parts you need to take off and other tools that are essential to getting specific parts off. And if you're trying to do it solo, that's going to make it even harder, especially trying to get the tranny back on by yourself and in a day. It look me 14 hours with a friend and with the right tools, knowing what I was doing. I think you might be in a little over your head with the limited tools and time you have. Good luck though if you attempt it!
@@nukem384 im going to be doing this once i get my clutch and flywheel here. been reading on some forms and most ppl have said they have done it in 3-7hrs, did you remove too much stuff to make it last longer than 7hrs? even my buddy changed a 2004 bmw clutch in 3hrs and said there is no way my car would take 14hrs to do.
@@ICELegit uhhh maybe if youre some pro mechanic. keep in mind i was also filming and doing all that, so that did take more time than usual. i think if i were to do it again, it'd probably take me like 8 hours. it all depends how fast you work too. if you can do it in under 7 hours, more power to you
@@nukem384 i did take in account that you were filming and that takes time to do. thats why i didnt think it would take a solid 14hrs, so i jumped onto some honda forms to see how long other people took to do it. some said 3hrs at a shop others said 5hrs with a friend and others saying no longer than 7hrs. than my buddy who changed that 04 bmw clutch last year said should take 4hrs. ... good video and good to know, start after work Friday and be driving to work Monday morning by the sounds of it.
@@ICELegit it depends how good you are with cars. it took that long because i took my time and didnt want to break or strip any bolts. sometimes guys on the forums exaggerate to make them look like geniuses. trust me, it's going to take you longer than 3 hours to do this install, i dont care how good you are. thats why when you take the car to a shop for this install, they tell you the car will be there all day, if not longer. i budgeted 2 whole days to do this install, but luckily it didnt take that long. its your time and your car, so you can do whatever you want. im just telling you how long it took me
I've been having trouble getting mine into Drive... will A new clutch help my problem?
Haha I hope you're trolling me. Automatics don't have clutches, they do have a torque converter though. It's not exactly the same install, but getting to the clutch/flywheel would be the same.
@@nukem384 I was curious because when I took it to the dealer, they told me my Drive oil was low and if I paid to do a clutch, it would fix it
@@darinp5612 haha classic dealer rip off. If your gears aren't working correctly, you actually need a new transmission. The gear oil will just mask it for a while. Changing the clutch/torque converter won't do anything. It's just a lot of unnecessary work to fill the dealers pockets with money.
@@nukem384 They quoted me 2500 to do the clutch, you're saying this wouldn't solve it?
@@darinp5612 That quote is on the higher so, but at least it's accurate for that install. I'm don't think it would fix your problem TBH. I'd take the car somewhere else and get a 2nd opinion and see if they say the same thing.
This is the absolute best 7th gen civic clutch video! Thanks so much. Im close. Though I'm going to use an engine hoist to support the bell once I get it off, in place of a strong friend, so I doesnt fall on my face
thanks! lol, i actually would recommend a tranny jack over the engine hoist just because im not sure there's hookup points on the tranny? but yeah, i wouldn't want it falling on my face either haha
After watching this I realized. I'm not getting paid enough to do these damn repairs. Nope, take that to the shop and pay someone else to do it lol
Haha, if you're doing it with your friends, you better enjoy working on cars or yes, not worth it at all.
so quick question all 3 motor mounts need to come off or just the side one?
100% you need to take the trans mount and rear mount off (both connected to tranny). You can try and get away with not taking the front mount off, but I found it was way easier, gave you a lot more wiggle room, and that mount is really easy to take off. Links to all the mount installs are in the description if you need!
nukem384 okay and if I want to take the tranny out by removing the subframe do I need an alignment afterwards? I have to replace the throw out bearing
@@devicetrickz I would get one. Any time you're messing with alignment, it's good to get that reset. Throw out bearing replacement is standard with a clutch install. It's shown in my video.
nukem384 I got the subframe removed and the clutch re installed wanted your thoughts on why it's making noise from the throw out bearing. Sounds like it's coming from that area either not lubricated properly or did we install it wrong?
@@devicetrickz My guess is not enough lube. You can't really mess that piece up. As long as the fork is thru the bearing, it should be good. Check the pivot ball as well, both those contact points in the tranny and on the fork. That can make quite a bit of noise if it's not lubed up.
Hey man one question why my 5th gear doesn't work?
Probably something wrong with the tranny. Not something that’s going to be easy to fix TBH
Ok because all the gears works but when I want to go to the 5th gear a goes but when I let the clutch go pops out the gear
Is this on a automatic transmission or manual? Someone said that my start clutch is going out and i have a automatic. (2006 Honda Civic Hybrid)
Manual. Whoever said that is totally wrong because automatics don't have clutches. They do have torque converters though, which takes the place of the clutch/flywheel.
@@nukem384 they actually do have clutches and many many many of them just a different kind of clutch but the same principle.
drop the subframe,so much more room 4 hours start to finish for the whole job
Do u have any tutorial of transmission replacement ?
im assuming you mean like taking the gearing apart and synchros and stuff? sorry i do not, but there are a bunch on youtube if you do a search
brlliant
Glad it helped
becareful anyone whos taking off the strut bolts , one of them are camber bolts. Make sure you mark the bolt.
About to do this today, but it’s a 03 civic
Good luck! Should be exactly the same as they are the same gen car
Jessika how did it go??
Easier to drop the subframe my friend
so basically, i should wait til my clutch goes out, and if they're bad, swap my axles along with my clutch. nice.
I can’t get the flywheel bolts out for nothing.... feels like there 1000ft lbs
a couple things you can try. pb blaster if the bolts are rusty for some reason. let that soak for a couple hours. or you can try some heat. use a torch and heat the bolts up. a lot of times that makes them easier to get off. power tools also help as well if you have them
nukem384 yea I tried a torch with not a lot of luck. I’ll try some penetrating oil. It’s hard to get a long enough breaker bar on.
@@517cliff you might want to try a steel pipe instead? like the one i have in the video. heavy pipes seem to help me a lot more than those standard breaker bars. i will usually put my heavy pipe over the breaker bar for more torque
nukem384 got 5 out stripped the last one now idk no room to pound a damaged bolt socket on without taking trans out
ouch that hurts. youre probably going to have to drill it out. now youre getting beyond the scope of work i usually do :(
How much swearing and cursing was involved? Just wondering
Lol! i was really mentally prepared for this install, so i actually didnt even swear once! but if i hadnt been, it probably wouldve been infinite swearing. like i said in the video, it wasn't really that bad at all, but it did take a long time since theres so many things you need to remove
Dude ! Ive watched quite a few of these tutorials and have been stuck in a friends garage the past 2 weeks trying to get mine done. once i had the trans separated and was pretty ticked off at the fact he hadnt followed through with his part in helping as we discussed prior and i was gone at work the next day he decided to go and start working on it and took the old clutch off and put the new one on and no resurfacing of the flywheel or even so much as a brake clean spray down nor did he properly torque anything. Basically half assed it enough to push it out onto the street and watch me go nowhere because of his bs. Axles werent even all the way in. I had previously had a bad axle seal on the drivers side and tried replacing it months ago but still had a small leak so i ordered two new ones for this go round hoping to keep my trans in better shape than before whereas i had no 5th gear and bought it that way thinking oh its a honda it cant be that hard or expensive to figure out. Lol i wasnt at all educated on these 7th gens and how many issues they had with especially the trannys whether auto or manual. Id done hours upon hours of searching and read numerous posts about others that lost 5th gear and the huge list of things theyd done to try fix it, some spending upwards of 1500 with them doing the clutch/flywheel,throw out bearing, synchros,forks, axles, checking linkage under center consoles, motor mounts, and the complete rebuilds with the gears and ofcourse adding trans fluid before all of those things and the problem still came back! From my knowledge and research these trannys are very very particular on the fluid that goes into them. Most guys say to go by the manual and put the honda mtf in it nothing else and a few others have said the gm synchromesh has worked for them. Well un knowingly this past winter i had put some lucas stop leak in and more than likely made my problem worse as i later found out there is a narrow pickup tube that is the port or passage for the fluid to get to the 5th gearset and when you put anything beside the known fluids in these they tend to get clogged up and result in little to no fluid and later slipping and grinding down the teeth in any future attempts to use 5th. One guy who claimed to be a honda tech for 20 plus yrs had mentioned the above statements and id watched a trans rebuild video to better understand it in hopes to solve my problem. He even stated that a person could actually take the outer casing on the pass side on trans off to access 5th gearset and components without removing the trans from the car. The few mechanic friends ive got had more so laughed at me when id brought this up so i never did attempt it as they thought itd do more harm than good. Im still having to tow my car back home ( 30 miles away ) to do everything over again because w.e he did wasnt right and id like to make the best effort i can to get it working as intended again. The clip for the shift fork and throwout bearing wasnt done correctly either im quite sure as it came right out after about 6 hrs trying to bleed the system having removed the pedal and replacing the clutch master cylinder. Now waiting for a new slave cylinder which wont arrive til tuesday. This has been way to long a project and a major pain in my a$$. Also caused allot of late days and on friday an absent day from work. I like my job and am hoping ive still got one tomarrow. This tutorial is by far the best one of all the ones I've watched. You covered everything and did it similar to the way i did without the hassle of removing the subframe. Hoping to get it towed today and get it on stands again to do the job the right way. My clutch wasnt even worn down badly at all it was just in pieces.. springs come out and been lodged inside for a while so hoping that my 5th gear problem be solved as another guy had the same problem and solved with new clutch. Again man many thanks as ill be using this vid for reference to speed up the process this go around. And if you arent already a member of the 7th gen civic page be sure to join up. We need more vids like this for the guys tryn to keep these things on the street and out of the scrap yards.
Tanner Germain first off, you definitely win the award for longest comment in any of my 300+ videos lol. Damn man, time to dump your “friend” who didnt seem to be a friend at all. Glad my tutorial helped! Thats what i was going for, the most in depth, detailed tutorial possible! I always use nothing but genuine mtf and genuine manf fluid in general since you know its made by the engineers that designed the car. Good luck with the install the 2nd time around and hope it goes smoother for you! Find a better friend this time! Thanks for the comment!
@@nukem384 yea thats the worlds longest youtube comment right there. shit should be on Ripley's believe it or not.
@@Mrpoker-hr1ud lol for sure. took forever to read lol
Dang Tanner. If this is how your RUclips comments are, I can't imagine what your 7th Gen Civic posts are like
So why didn't you replace the crank shaft seal you were in there and would be a good idea to replace it also if you have the axles out you should replace the axle seals and one more thing I would suggest removing the lower ball joints and doing it that way because technically you should at least check the alignment it could change even though there is no adjustment there and also if you do it at the ball joints there is no need to remove the brake calipers but the rest of the video was pretty good
You did not have to remove the subframe
Nope. I didn't want to do that because it would take forever and not really necessary
22 people messed the job up
Lol, apparently. Thanks, appreciate the comment! :D
185k later here i am
Nice. Good amount of miles on that clutch. Good luck!
@@nukem384 I appreciate the words of encouragement! I figure 1 day to knock it out
@@jowa1978 Yeah 1 day is good. Took me about 14 hours to do with a friend, but that is also including a lunch and dinner. So maybe like 12 hours of work for a DIYer.
Getting ready to knock this out 338000 miles original factory clutch, i know its the original bc we bought this new back in 2002.
This will be fun to do.
Thanks for the tutorial and tips.
@@noneyabusiness368 I'd say you know how to drive a stick pretty well if you've held on to the original clutch that long! Very impressive. Good luck on the install!
good video but it’s horrible to put a bare battery on a concrete floor!
Thanks. The battery starting to leak or discharging being put on a concrete floor is an old school way of thinking. Back in the day, when batteries and cars were not as advanced, this would totally be true. Today's batteries are not designed the same anymore and it's fine to put them on a concrete floor for half a day. Thanks for the concern though.
Way too complicated... me ran away watching half way through the video. This is literally taking part of engine and transmission off the car...plus the wheel hub. Looks like the shop isn't charging all that much considering all this work involved. I will have shop to replace my clutch once it goes bad
Haha, I did warn you that it was involved! Saving at least $1,000 in labor, for me anyway, was totally worth it and I can check this box off my list! Not for everyone though.
@@nukem384 Where do u live? once my clutch goes bad (it's worn out bad already) can you replace clutch n flywheel for me for cheap? Labor maybe $300? I have an '03 Civic EX 5 spd I live in Indianapolis...
I_need_1_Decillion_Dollars sorry, dont live anywhere near you. Maybe throwing an ad on craigslist might help if someone is willing?
@@nukem384 I'll try that thanks for the idea
And don't forget you're cheater bar
Definitely need that around for this install