It's much harder to find someone who pronounces Volkswagen correctly. I took 4 years of German in high school/college. But people in the US look at me funny when I pronounce it correctly. In a nutshell, German doesn't have the English w sound. Instead, the w is pronounced like the English v. And the v is pronounced like the English f. And the a has an "ah" sound rather than the "eh" English uses.
Feel free to throw the water pump as hard and far as possible. M96 water pumps are a known failure item; replacing them is "routine" maintenance (like every 50k miles IIRC). Nice to see the engine torn down as far as it was; I now appreciate my 996's motor that much more.
Yeah, I'm on one replacement (plus the original) and I'm at 119k miles. Half of the vanes on my original were broken off... Very dramatic barfing of coolant under the car when it totally gave out as I backed into the garage after some spirited driving...
why do they have pourshe racing,, cos they can only race each other,, as there pendulums.. dont like corners, unless you have 26'' wide tyres.. only decent poursche, is the v8,,in front..948. ill keep my clevo. 351.. 15 yrs, no probs, $26 services..
problem with expensive cars,, people dont drive, thrash them, as there expensive to fix, but if you dont drive them, they fk up anyway.. plus, a lot of ''people'', that own them, cant fkn drive..more money than gray matter.. or service them as its hundreds, thousands of dollars.. & synthetic oil is garbage..3000k, change it..
Watching this video just shows how masterful you really are in your craft. I know there are countless hours of footage that are cut, and even more off camera time looking up manuals and procedures on any first-time teardown, but once put all together then edited into the final product… it’s an absolute thing of beauty. While I do enjoy watching you throw parts across your shop and tell jokes while beating on an old LS, I still want to say thank you for allowing us the privilege of watching you work for your business. Finally, this is another fine example of content that this channel provides, sometimes its complete carnage, sometimes it’s good old dad jokes and spicy tacos, but then these rare times it’s a more serious first-time tear down, but every time it’s always a great video. Thanks again.
I had a 2004 986 S and tore my 3.2 out and did the IMS repair and sold the engine for a big chunk of money because it ran and was worth something. Bought a wrecked 2004 Carrera S 997 and pulled the 3.6 M96 and swapped it into my 986 S. With cams intake and exhaust it made 360whp. Thing was an absolute rocket. Sold it last year for $25k. It was bittersweet selling it.
Yeah, I hear ya. I've got a 1997 986 chassis with the 3.4 and bigger brakes swapped from a 2001 Carrera (the original 2.5 had an IMS failure, who woulda thought?). The '97 is the lightest 986 they built, which is nice, and the motor with headers, some ECU tweaks and good intake plumbing puts out about 290whp on the dyno. Nowhere near your 360, but still gets you into severe traffic violation territory at the slightest twitch of the right foot.
cool video Eric, there were no indications of lubrication failure in the parts you removed and examined so I totally agree with your decision to not strip the motor any further 👍
Even though you had to stop short ( perfectly understandable ) it was interesting to see the engineering ethos of Porsche. I am always fascinated to see how each engine builder drives their camshafts and valvetrains which, I feel, is their engineering signature. In this engine, everything seemed to be built to have a solid purpose with as few frills as possible. As opposed to Audi which seems to think the more parts, the better. If you have the chance to take apart an Audi V8 you will see what I mean. Keep them coming!
You did the right thing Eric. Enjoyed seeing the innards of that engine as far as you went. Actually, nice to see something that deserves some TLC while coming apart.
Loved the teardown, now I see what my 2003 Boxster S engine looks like inside ! 98k miles after 20 yrs, mine still runs smooth like butter ... Had the plastic coolant tank replaced, fuel sending unit, water pump, brakes and tires and that's about it. Still original ims bearing, looks sharp in kobalt metallic blue after some major detailing, red caliper repainting and re-lettering, and all new emblems.
I have never seen you be that careful taking things apart 🤣 I agree not tearing down the short block, I was thinking about this a few minutes before you mentioned it yourself 🙂
I really looked forward to see a 6 cylinder boxer engine torn down, but after the first head came off i knew where we were headed, and i think you made a good (and the right) call of not going further, those bores looked way too beautiful.
I do love your show. 1968 was my last year of high school and my auto mechanics class. Mr. Duncan had 4 of us rebuild a performance 327 with supplied parts. We were ready to start it and it locked up. We had put the domed pistons in backward. Mr. Duncan laughed and told us that we knew what to do. I loved that class. Old LB
Funny...my brother (1 yr younger) and I doing same thing. Him a 327, me 283 to 301, both 11:1++++. Mine complete and in his 63 temporary. He's to heads, arguing with my dad in garage, calls me out.."is this right?" Me "NO" and go back into house chuckling...interesting dome pattern. "Can I swap pistons/rods?" Me "No" 1969/1970, 16/17 yo gearheads...best of times
My guess is someone might have went to change the IMS cover seal or even IMS and didn’t have the camshafts locked. It jumped time and valves hit when started. The only annoying part rebuilding these engines is finding a place they can deal with cylinder liners. Those bores look excellent The real sad part is the valves are pretty cheap to replace.
I concur with this. There's no way the contact happened when Eric turned it over manually. It had jumped time and made contact prior, likely when someone attempted to service the IMS. Bummer the engine was scrapped when it could easily have been repaired.
I watched this one to learn what happened to the engine. I was disappointed that you didn't provide a better explanation as to what/how/why the failure occurred. I often tear down engines at work and love to figure out exactly what happened.
This one was interesting. I bought a Y2K Boxster S used for $25K and it was a great car. I was enjoying it for a few months until I heard about the IMS failure that could happen without warning, and Porsche wasn't backing it up with any kind of recall or warranty. I took the car to a Porsche car show hoping to sell it when I discovered a 28K mile black 930 turbo coupe for sale for only $31K (before the big price surge). So it all worked out peachy. That Boxster engine makes music and it did run great but I wasn't about to dump $15K into a new engine just in case it decided to explode backing out of the driveway.
the height of the intake plenum and runners fools the eye - in the car, the heads would be below the knee. They are wide side to side, but low Cg with that engine design
@jordansling.. Thats what i need to be doing.. sparkplugs.. glad u mentioned it and removing the rear wheels .. great reminder of makin it easier, never done em b4.. But also havent been driving the car more since i havent done em. I got the plugs about 2 months ago (tryin out some Iridiums .. single ground strap, as opposed to the 4 strap, oem copper Bosch. Share any ideas or advise u may have about this.
Very cool seeing the construction of a German engine that didn't appear to be excessively over designed or more complicated than necessary. It looked well done.
The RTV in the pick up screen is most likely from a leaking rear main seal replacement. If the seal has been replaced multiple times, or “required” RTV to install it, it is very likely the casting of the case where the crank exits is oversized or not round. That was the issue with the M96 motor in my Carrera. A very common problem. You mentioned the IMS failure to be blown out of proportion by the internet? Well it was bad enough for a class action lawsuit to be won against Porsche, so I’d say the problem was pretty widespread.
The "E" and "A" labels on the cam caps probalby refer to "Einlass" and "Auslass" - Intake and Exhaust in German. Likely checked and labeleyd before assembly.
Thanks for stopping where you did. You've likely not only made a good financial decision, but that short block will be appreciated by someone else in its current state. Very interesting to see the inside of that engine (I have a 996 so very interesting) - hope you do well out of this core 🙂 Thanks for the great content !
I am very impressed on how clean and simple the M96 engine is designed. I just watched a video of a m20 bmw engine and it was a NIGHTMARE! Good on ya, volkswagen, i mean porsche
I bought a Boxster S with that engine. First thing I did was replace the IMS , Clutch and Flywheel. I broke 3 pullers trying to pull the IMS. I ended up cutting it apart with a dremel tool. Been a weekly driver for 4 years now no issues.
It’s refreshing to watch an engine that doesn’t puke piston nuggets in a bath of extra glittery sludge, love the content and glad to watch you unpack that lump of German performance engineering
I have a 24-year-old 2000 Porsche Boxster S (built in late-1999). Never had the engine removed or apart, zero engine issues except for an AOS replacement and a couple of coolant reservoir leaks, failed water pump replacement (very dramatic barfing of coolant under the car as I backed into the garage), plus cracked ignition coils that were overdue for replacement, and all of which I kept up on and replaced myself. That's it engine-wise. Every time I change the oil or plugs they look great, as well as the oil filter which I tear open to check every pleat for debris. Always pretty clean except for used oil. And I drive it hard every day, even through mountain switchbacks at 12,000 feet altitude. These engines like to be wound out responsibly. Mine still goes like stank. Generally, if you have nice things, you have to pay attention and take care of them. Is there still a chance of catastrophic failure? Yup. But you can do your best to minimize that probability and a little luck helps. Porsche is indeed a two-syllable word. 😉
True, although I also follow a reputable German engine specialist (Redhead. sorry, YT videos are in German) who said on YT that Porsche Boxster engines are not standard meant to go on trackdays. If you want to drive them that hard, you must say so when purchasing them and you will get a stronger engine (provided you pay extra, of course). He also mentioned what differences there were, but sorry, I forgot. Personally, that would be the limit for me. Paying extra to do what the car was meant for is beyond me. And oh, coils are not parts that should ever be replaced routinely. In principle they should last the engine. I know that is not always the case, but still.
@@ronaldderooij1774the coils Porsche used prior to roughly 2010 eventually degrade and crack. In roughly 2010 Porsche updated the coils and they are much better. When people do the spark plugs on cars with the previous style coils they're recommended to update them to the latest version.
Wow, that was a hell of a tear down, good luck selling the long block... And I fully understand why you stopped there... Thank You Eric another Epic tear down...
Did you know that if you cut a piece of plywood to fit across the legs of your engine stand you can drill holes in it where those cranks go down through that would keep it in position and keep your drain pan where you want it
The E or A on the cam caps is for intake (Einlass) or exhaust (Auspuff). Cause an E on the intake isn't confusing or anything, Germany! No clue on the numbers.
I'm driving my 4th Porsch-ah right now and never have I even seen the engines! Embarrassing, I know. As a DIY'er in everything else, I draw the line here with my cars. But, watching this video and seeing up close what I've paid thousands and thousands to repair (including an ims upgrade) , was both educational and oddly relaxing. Thanks for the trip!
As an owner of a 2004 986 3.2S this was really interesting. I have owned mine from 10 000 miles and it now has 27 000 on it. After mulling over the IMS bearing issue I decided I wanted to be able to drive the car as intended without constantly listening for the first signs of a failed bearing and had it replaced with an improved aftermarket item from EPS. These cars sound best when driven from 4000 rpm to the red line not that you can do much of that on the public road.
Yeah, perfectly understand why you left it as a short block! Engine might as well have been gold plated, especially these days! Glad you'll make some money off of this for a change.
Big fan of this channel. Weirdly cathartic to see engines being stripped down and the pathology of why they failed. Also have learned about how IC engines are engineered. Thanks for sharing.
Kind of interesting, the gap between the cylinders, visible on both the block and heads, and the layout of the head bolts, suggest to me that Porsche, when designing this engine basically just took their old air cooled architecture and built some water jackets around the cylinders.
This looks like the shop diagnosed a Variocam failure (which does happen,) took it apart to start the repair (hence the marked caps,) found the cam was completely dead, and found the piston damage. Being a 3.4L M96 and susceptible to bore scoring, putting a known good used engine in became the cheaper option. It probably just needs the head reconditioned, but then you're pulling the engine, resealing it, may as well do the IMS while you're in there, pulling the pistons is likely to score the bore, you need all the special tools, all the labor, etcetera. I could easily see this being written up as a $40,000+ estimate. "Or, we can put a good used M96 with a new IMS in for about $15k."
Great video! As much as I’d like to see that short block in pieces, I totally understand. I would rather see that engine rebuilt and in a healthy vehicle. Great work!
I'm subscribed to a ton of channels on RUclips but yours is one of two that I have set up for notifications. I love getting the alert on Saturday night to watch your latest video.
Here's what I think happened. Someone did a timing job on the engine and forgot to torque the intake cam sprocket properly. I actually did the same thing on a jeep 3.7. Luckily my boss didn't fire me, I did fix it out of my own pocket. Learned a valuable lesson that day.
Timing job, didn't look like any new gaskets on it and not a high mile engine except for oil the consumption. Why did it have valve interference on only one side, I guess it's a mystery engine. BTW, why no oil filter? Don't reply JiffyLube.
Don’t split the case haves on that short block. That short block is definitely worth some money. It’s ready for the IMS upgrade. What a great tear down. Loved every minute of it.
I do this exact job EVERY day at work. Absolutely love my job. I've tore down probably 30 of these engines and they can be a pain sometimes. Granted I dismantle or pallet up engines to be sold as a used engine Assembly. I Bielefeld we have 3 entire assembly for this engine and probably another 10 short blocks sitting on the shelves. They usually sell withen a month. A lot of the Porsche engines I've dismantled with higher mileage tend to have cylinder walls that have been torn and also the piston skirts have the same tearing marks. Some of the range rover engines have a similar tendency.
Even though I knew no Porsche water pump was gonna be thrown across the workshop, I had a sneaky suspicion you’d still sneak in a pump toss somehow, even if it was from a different engine. 😆
I like that you didn't pull the short block apart. You already found why it was a core. The whole "bottom" (what is that called on a boxer?) is in great condition, it hurts as a car guy to take apart something that works. I know you went to profit because you are a business, and I also remember you saying you hate taking apart something that's working. I appreciate that there will be some back-blow from people that just want to see a complete tear-down of this engine so justifying for the business needs to be emphasized when I'm confident that it being a working bottom is a great reason to stop there for anyone who has worked on engines before. As always, I enjoy your videos, good health and good fortunes to you and yours.
notice that there where any witness marks from valves touching the pistons on the second head removal ? Make you wonder if the loose cam gear bolt was the cause of the valves touching pistons ?
Yes, you stopped at the right point. I have a 1965 911 and It's amazing to see how far the 6 cylinder Porsche has progressed. I thought the cam chain setup was simpler than other engines you have torn apart.
I enjoyed this tear down. The engine appears to be a solid design, IMS notwithstanding. I'm a diesel guy, and a fan of iconic diesel swaps. I'd love to see you tear down an OM606 or TDI engine. These don't fail very often, but have some rare issues folks might appreciate viewing.
It could still have damage in the short block due to IMS bearing failure. In which case it's got to come apart assuming it's repairable, even if for no other reasoni than a thorough cleaning to get the metal bits out. I was really hoping to see the exploration of the IMS bearing and shaft.
Iirc the Intake cam isn’t staked on this engine. The central bolt can loosen over time (or not torqued on previous repair) and it will eventually lead to misfire faults. If you don’t catch it and drive home the bolt comes out too far and will prevent the cam from spinning. The loose cam sensor was probably the diagnosis and they assumed (incorrectly) that the cam had broken.
highly reccomend getting a strong neodymium magnet so you can hold it near the oil drain stream. for really f**ked motors the stream will arc towards the magnet.
Applause Applause...think you made the right decision--no need for an apology. You do run a business, I'd rather you make the correct decision for your company and your employees...
Good call not tearing down the short block, as much as I would have liked to see it. It was really interesting to see this video, even though you didn't tear it all the way down. This engine looks like it's in very good condition and it should be possible to rebuild it, even considering the intake camshaft. I hope you do really well on this engine, because you deserve it.
Hey, no worries. Business is business, and nobody wants to work for a loss. It was more than worth it, to watch that engine come part as far as it did...👍👍
It’s amazing how complicated and intentionally difficult to service these engines are, especially considering Subaru had a similar displacement engine (3.0 vs 3.2) with similar power (250 vs 258) starting at around the same time (Legacy 3.0R was available starting 2004 in Japan) but it was smaller, more reliable and *much* easier to service.
The Subaru H6 WAS NOT easy to service. I had the misfortune of having to do timing chains on one. Much like this engine, the entire powertrain had to be dropped. Even spark plugs are right against the frame rails on both sides of the engine bay. Granted they are one of the more reliable Subaru engines but that’s because there’s nothing to them.
These things were made during a time when Porsche was in bad shape financially, so they had to cut costs by reusing the same head casting for both sides. That's why there's timing chains on both sides of the block. Keep in mind the Boxster S 3.2 was intentionally tuned very conservatively so it wouldn't interfere with the base 3.4 911, and that 260hp figure is for the EZ36, not the EZ30 (which made 220 or 240 depending on the year).
hi I had a similar case on the same engine, my client had over-revved the engine which took a lot of rpm and the valves met the pistons, the same screw on the camshaft was loose, nothing broken, we have completely overhauled this engine, with new chains and shoes, connecting rod bearings and bearings, seal valves, and since this event it has already covered 30,000 kms without any problems.....
Im so happy you didnt tear down that engine completly. It was hurting me to watch that engine teardown as the engine was in a very good condion. Hope somone rebuild that engine. Hope we will see some destroyed Porsche engine one day. Thanks and here's the like nonethless.
You do have a business to run and profit is definitely a good thing. Smart move on your part to end it where you did. It was interesting to see how the engine was put together. Thank you for that bit of it. Take care.
Of course there are some differences between mounting in Boxster and 911. In Boxster the engine is mounted right in front of the rear axle and in 911 it is mounted right behind the rear axle.
Bought my first LBZ Feb 2006…drive it 629,750 kms - then was stolen Jan 2023. Bought an 07 LBZ CCSB SLT. BEST motor, great trucks. Bypass Oil filter, Titan Tank, FASS….all 3 liberated from found stolen n smashed up 06 truck…
Well done and i appreciate leaving the short block unmolested. Just that one intake cam...head scratching here. Taking care of the business never a poor choice. Thx Eric.
IMS issue is cars that were rarely driven and in salt air climates. A garaged engine that is routinely driven is not a problem. The IMS bearing itself is sealed, but the seal pops off. Then the bearing gets splash lubricated and remains fine unless it gets exposed to air and moisture, because it's metalurgy is intended for it to remain sealed. Best way to counter the corrosion issue is by using HD diesel oil, like Rotella or Delvac. In extreme cases you can use a marine oil.... LiquiMoly makes some if that helps.
At some point before the 2nd head came off, I was thinking "That's a good short block" so it came as no surprise when you stopped after pulling the heads,
No need for the apology, you’re a business and as much as I love you tearing an engine down to the last nut and bolt you don’t need to do that to your financial detriment just to appease the masses😂 I look forward to you getting a GT3 engine in for a tear down
I was captivated at this video as it demystified disassembly of a Porsche engine. I'm a novice, and this is a novice question I guess: Is this an engine you intend to part out? Why wouldn't you replace / repair the head and damaged valves and reassemble the engine? You said many times that aside from the head/valves the engine was in good shape. Thank you. Best youtube video I have seen in months.
You have got to pull the rod caps on the sidethat crashed the valves on the boxter why did they hit ,cam phaser or rod clearences, it would drive crazy until i checked. Keep up the good work i enjoy your teardowns
Porsche is not a 2 syllable word.
yes it is
The people who make the car think otherwise 🤷♂️
Ja. Learned that at the factory showroom in Stuttgart many years ago
There are no silent e's at the end of German words,
The German pronunciation is two syllables.
Anyone who pronounces the name 'Porsche' the correct two-syllable way definitely gets my respect ! 👍👍
It's much harder to find someone who pronounces Volkswagen correctly. I took 4 years of German in high school/college. But people in the US look at me funny when I pronounce it correctly.
In a nutshell, German doesn't have the English w sound. Instead, the w is pronounced like the English v. And the v is pronounced like the English f. And the a has an "ah" sound rather than the "eh" English uses.
Feel free to throw the water pump as hard and far as possible. M96 water pumps are a known failure item; replacing them is "routine" maintenance (like every 50k miles IIRC). Nice to see the engine torn down as far as it was; I now appreciate my 996's motor that much more.
Thay are only an over engineered vw flat 4
@@garrypritchard1658you ever drive one?
Yeah, I'm on one replacement (plus the original) and I'm at 119k miles. Half of the vanes on my original were broken off... Very dramatic barfing of coolant under the car when it totally gave out as I backed into the garage after some spirited driving...
why do they have pourshe racing,, cos they can only race each other,, as there pendulums.. dont like corners, unless you have 26'' wide tyres.. only decent poursche, is the v8,,in front..948. ill keep my clevo. 351.. 15 yrs, no probs, $26 services..
problem with expensive cars,, people dont drive, thrash them, as there expensive to fix, but if you dont drive them, they fk up anyway.. plus, a lot of ''people'', that own them, cant fkn drive..more money than gray matter.. or service them as its hundreds, thousands of dollars.. & synthetic oil is garbage..3000k, change it..
Watching this video just shows how masterful you really are in your craft. I know there are countless hours of footage that are cut, and even more off camera time looking up manuals and procedures on any first-time teardown, but once put all together then edited into the final product… it’s an absolute thing of beauty. While I do enjoy watching you throw parts across your shop and tell jokes while beating on an old LS, I still want to say thank you for allowing us the privilege of watching you work for your business. Finally, this is another fine example of content that this channel provides, sometimes its complete carnage, sometimes it’s good old dad jokes and spicy tacos, but then these rare times it’s a more serious first-time tear down, but every time it’s always a great video. Thanks again.
Well said, I’m glad Eric is showing us , I been retired for 26 years and I’m glad I’m out I will stick with my dinosaur cars and trucks.
Yes, not tearing down the short block is the right decision.
Besides, it's no fun if there's no carnage to revel in.
But it’s a huge gamble,
Is the engine block not perhaps cracked somewhere?
@@manuqtix8874 thats the job of a machine shop
@@manuqtix8874- buying used vehicle parts is always a gamble. 🤷🏻♂️
Will anyone buy the short block knowing that there has been piston-to-valve contact?
@@robj2704 as long as it ain’t cracked it’s fine
I had a 2004 986 S and tore my 3.2 out and did the IMS repair and sold the engine for a big chunk of money because it ran and was worth something. Bought a wrecked 2004 Carrera S 997 and pulled the 3.6 M96 and swapped it into my 986 S. With cams intake and exhaust it made 360whp. Thing was an absolute rocket. Sold it last year for $25k. It was bittersweet selling it.
Yeah, I hear ya. I've got a 1997 986 chassis with the 3.4 and bigger brakes swapped from a 2001 Carrera (the original 2.5 had an IMS failure, who woulda thought?). The '97 is the lightest 986 they built, which is nice, and the motor with headers, some ECU tweaks and good intake plumbing puts out about 290whp on the dyno. Nowhere near your 360, but still gets you into severe traffic violation territory at the slightest twitch of the right foot.
Sounds like youre a champ with these engines. Loved hearing this story u wrote.
@RadDadisRad, What did the 3.2 you sold fetch if you don't mind me asking? I'm looking at a wrecked Boxster and hedging my bet if it were to go South.
Why did you sell it?
cool video Eric,
there were no indications of lubrication failure in the parts you removed and examined so I totally agree with your decision to not strip the motor any further 👍
This is most friendly and gentle engine teardown in the channel history. 😅
Even though you had to stop short ( perfectly understandable ) it was interesting to see the engineering ethos of Porsche. I am always fascinated to see how each engine builder drives their camshafts and valvetrains which, I feel, is their engineering signature. In this engine, everything seemed to be built to have a solid purpose with as few frills as possible. As opposed to Audi which seems to think the more parts, the better. If you have the chance to take apart an Audi V8 you will see what I mean. Keep them coming!
I'm in the same boat. The timing cover removal is my favorite part. The Bentley tear down blew my mind, gear driven timing.
Thank You for not having music for your background, I can’t stand in on all the others, we just want you to do your thing and be yourself.
You did the right thing Eric. Enjoyed seeing the innards of that engine as far as you went. Actually, nice to see something that deserves some TLC while coming apart.
Loved the teardown, now I see what my 2003 Boxster S engine looks like inside ! 98k miles after 20 yrs, mine still runs smooth like butter ... Had the plastic coolant tank replaced, fuel sending unit, water pump, brakes and tires and that's about it. Still original ims bearing, looks sharp in kobalt metallic blue after some major detailing, red caliper repainting and re-lettering, and all new emblems.
If the car is blue, why paint the calipers red?
@@blackmanops3749cars that come with the sport brake packages have red calipers. Yellow for PCCBs. Green for performance hybrids.
I have never seen you be that careful taking things apart 🤣
I agree not tearing down the short block, I was thinking about this a few minutes before you mentioned it yourself 🙂
This engine is actually HUGE! WOW! Takes up a lot of space on a mid or rear engine car.
Real heavy too. Supposedly 40lbs heavier than an all aluminum LSV8
I really looked forward to see a 6 cylinder boxer engine torn down, but after the first head came off i knew where we were headed, and i think you made a good (and the right) call of not going further, those bores looked way too beautiful.
I do love your show. 1968 was my last year of high school and my auto mechanics class. Mr. Duncan had 4 of us rebuild a performance 327 with supplied parts. We were ready to start it and it locked up. We had put the domed pistons in backward. Mr. Duncan laughed and told us that we knew what to do. I loved that class. Old LB
Funny...my brother (1 yr younger) and I doing same thing. Him a 327, me 283 to 301, both 11:1++++. Mine complete and in his 63 temporary. He's to heads, arguing with my dad in garage, calls me out.."is this right?" Me "NO" and go back into house chuckling...interesting dome pattern. "Can I swap pistons/rods?" Me "No" 1969/1970, 16/17 yo gearheads...best of times
My guess is someone might have went to change the IMS cover seal or even IMS and didn’t have the camshafts locked. It jumped time and valves hit when started. The only annoying part rebuilding these engines is finding a place they can deal with cylinder liners. Those bores look excellent
The real sad part is the valves are pretty cheap to replace.
I concur with this. There's no way the contact happened when Eric turned it over manually. It had jumped time and made contact prior, likely when someone attempted to service the IMS. Bummer the engine was scrapped when it could easily have been repaired.
Exactly what I was thinking
I watched this one to learn what happened to the engine. I was disappointed that you didn't provide a better explanation as to what/how/why the failure occurred. I often tear down engines at work and love to figure out exactly what happened.
Thanks for sharing. Love seeing Porsche, now Ferrari next…
We did a while back. Technically it was out of a Maserati. But it's a Ferrari designed engine.
Imagine W16 bugatti engine teardown.
@@1Ministras Oooooohhhhhh.... I have not even dared to hope for a W engine... that would be the most epic teardown possible, by far.
FERRARI.
STOP, CEASE, DESIST
@@ChaseMMDwe?
This one was interesting. I bought a Y2K Boxster S used for $25K and it was a great car. I was enjoying it for a few months until I heard about the IMS failure that could happen without warning, and Porsche wasn't backing it up with any kind of recall or warranty. I took the car to a Porsche car show hoping to sell it when I discovered a 28K mile black 930 turbo coupe for sale for only $31K (before the big price surge). So it all worked out peachy. That Boxster engine makes music and it did run great but I wasn't about to dump $15K into a new engine just in case it decided to explode backing out of the driveway.
Aftermarket IMS fix is bulletproof.
Do you still have that black 930 ?
They demoed the after market fix on Wheeler Dealer. Not very hard to do, Ant did it with engine in car. Not sure which car.
@@vladpcgamer No, I sold it in 2015. I have a mini review video of it on my channel somewhere... it was really clean.
@@RadDadisRad That's good to know. I'd like to revisit the Boxster S ... maybe a newer version than I had before.
That motor looks much bigger than I expected
That's what she said
They are, you have to take off the rear tires and change the spark plugs in the wheel wells. Which actually makes it pretty easy
They're wide, but quite short front-to-back. Boxer engines tend to be.
the height of the intake plenum and runners fools the eye - in the car, the heads would be below the knee. They are wide side to side, but low Cg with that engine design
@jordansling.. Thats what i need to be doing.. sparkplugs.. glad u mentioned it and removing the rear wheels .. great reminder of makin it easier, never done em b4.. But also havent been driving the car more since i havent done em.
I got the plugs about 2 months ago (tryin out some Iridiums .. single ground strap, as opposed to the 4 strap, oem copper Bosch.
Share any ideas or advise u may have about this.
Very cool seeing the construction of a German engine that didn't appear to be excessively over designed or more complicated than necessary. It looked well done.
Love the respect you show to this engine.
The RTV in the pick up screen is most likely from a leaking rear main seal replacement. If the seal has been replaced multiple times, or “required” RTV to install it, it is very likely the casting of the case where the crank exits is oversized or not round. That was the issue with the M96 motor in my Carrera. A very common problem. You mentioned the IMS failure to be blown out of proportion by the internet? Well it was bad enough for a class action lawsuit to be won against Porsche, so I’d say the problem was pretty widespread.
The "E" and "A" labels on the cam caps probalby refer to "Einlass" and "Auslass" - Intake and Exhaust in German. Likely checked and labeleyd before assembly.
Thanks for stopping where you did. You've likely not only made a good financial decision, but that short block will be appreciated by someone else in its current state. Very interesting to see the inside of that engine (I have a 996 so very interesting) - hope you do well out of this core 🙂
Thanks for the great content !
I am very impressed on how clean and simple the M96 engine is designed.
I just watched a video of a m20 bmw engine and it was a NIGHTMARE! Good on ya, volkswagen, i mean porsche
Homie goes out and buys white gloves for a 5 second joke. Lol love it.
I bought a Boxster S with that engine. First thing I did was replace the IMS , Clutch and Flywheel. I broke 3 pullers trying to pull the IMS. I ended up cutting it apart with a dremel tool. Been a weekly driver for 4 years now no issues.
An expensive core that you've been looking for? That's hardcore.
It’s refreshing to watch an engine that doesn’t puke piston nuggets in a bath of extra glittery sludge, love the content and glad to watch you unpack that lump of German performance engineering
I have a 24-year-old 2000 Porsche Boxster S (built in late-1999). Never had the engine removed or apart, zero engine issues except for an AOS replacement and a couple of coolant reservoir leaks, failed water pump replacement (very dramatic barfing of coolant under the car as I backed into the garage), plus cracked ignition coils that were overdue for replacement, and all of which I kept up on and replaced myself. That's it engine-wise. Every time I change the oil or plugs they look great, as well as the oil filter which I tear open to check every pleat for debris. Always pretty clean except for used oil. And I drive it hard every day, even through mountain switchbacks at 12,000 feet altitude. These engines like to be wound out responsibly. Mine still goes like stank. Generally, if you have nice things, you have to pay attention and take care of them. Is there still a chance of catastrophic failure? Yup. But you can do your best to minimize that probability and a little luck helps. Porsche is indeed a two-syllable word. 😉
True, although I also follow a reputable German engine specialist (Redhead. sorry, YT videos are in German) who said on YT that Porsche Boxster engines are not standard meant to go on trackdays. If you want to drive them that hard, you must say so when purchasing them and you will get a stronger engine (provided you pay extra, of course). He also mentioned what differences there were, but sorry, I forgot. Personally, that would be the limit for me. Paying extra to do what the car was meant for is beyond me. And oh, coils are not parts that should ever be replaced routinely. In principle they should last the engine. I know that is not always the case, but still.
@@ronaldderooij1774the coils Porsche used prior to roughly 2010 eventually degrade and crack. In roughly 2010 Porsche updated the coils and they are much better. When people do the spark plugs on cars with the previous style coils they're recommended to update them to the latest version.
Wow, that was a hell of a tear down, good luck selling the long block... And I fully understand why you stopped there... Thank You Eric another Epic tear down...
It's interesting seeing the different between the treatment of "mass production" engines vs. something a little more rare.
You can actually see the $$$?
Yeah. I've got a good imagination. ;-)@@josephbidon4333
There is no discrimination - He caresses and cherishes even the cheapest timing chain.
@@johncoops6897 He has his name down in case he decides to enter the Hip-Hop scene. Instead of 2-Chains he can call himself T-Chanz .
@@prevost8686 - yep, agreed. Eric T-chainz 😃
Did you know that if you cut a piece of plywood to fit across the legs of your engine stand you can drill holes in it where those cranks go down through that would keep it in position and keep your drain pan where you want it
The E or A on the cam caps is for intake (Einlass) or exhaust (Auspuff). Cause an E on the intake isn't confusing or anything, Germany! No clue on the numbers.
I'm driving my 4th Porsch-ah right now and never have I even seen the engines! Embarrassing, I know. As a DIY'er in everything else, I draw the line here with my cars. But, watching this video and seeing up close what I've paid thousands and thousands to repair (including an ims upgrade) , was both educational and oddly relaxing. Thanks for the trip!
Really hope to see a rotary engine teardown on this channel
I think he did. Did a Mazda RX-8 rotary.
As an owner of a 2004 986 3.2S this was really interesting. I have owned mine from 10 000 miles and it now has 27 000 on it.
After mulling over the IMS bearing issue I decided I wanted to be able to drive the car as intended without constantly listening for the first signs of a failed bearing and had it replaced with an improved aftermarket item from EPS. These cars sound best when driven from 4000 rpm to the red line not that you can do much of that on the public road.
Thank you Eric for the Porsche teardown. I appreciate your efforts more than you realize.
I am not even a car guy and enjoy your videos. 90% of the time I have no idea what the parts are even called. Well done keeping us entertained 😊
Yeah, perfectly understand why you left it as a short block! Engine might as well have been gold plated, especially these days! Glad you'll make some money off of this for a change.
Big fan of this channel. Weirdly cathartic to see engines being stripped down and the pathology of why they failed. Also have learned about how IC engines are engineered. Thanks for sharing.
Kind of interesting, the gap between the cylinders, visible on both the block and heads, and the layout of the head bolts, suggest to me that Porsche, when designing this engine basically just took their old air cooled architecture and built some water jackets around the cylinders.
Bought a used Porsche M96 3.4 from R&D exotics 3 years ago still running great today with no problems
This looks like the shop diagnosed a Variocam failure (which does happen,) took it apart to start the repair (hence the marked caps,) found the cam was completely dead, and found the piston damage. Being a 3.4L M96 and susceptible to bore scoring, putting a known good used engine in became the cheaper option. It probably just needs the head reconditioned, but then you're pulling the engine, resealing it, may as well do the IMS while you're in there, pulling the pistons is likely to score the bore, you need all the special tools, all the labor, etcetera. I could easily see this being written up as a $40,000+ estimate. "Or, we can put a good used M96 with a new IMS in for about $15k."
Thanks for sharing! Took a while to find an explanation that makes sense.
OMG, When Eric changed his gloves at the beginning, I lost it. That was perfect. Bless you Eric
Great video! As much as I’d like to see that short block in pieces, I totally understand. I would rather see that engine rebuilt and in a healthy vehicle. Great work!
How many views, subscribes, 👍, and comments would it take to see that short block disassembled?
I'm subscribed to a ton of channels on RUclips but yours is one of two that I have set up for notifications. I love getting the alert on Saturday night to watch your latest video.
Here's what I think happened. Someone did a timing job on the engine and forgot to torque the intake cam sprocket properly. I actually did the same thing on a jeep 3.7. Luckily my boss didn't fire me, I did fix it out of my own pocket. Learned a valuable lesson that day.
holy shit u have to pay mistakes by urself? not here in Finland
Timing job, didn't look like any new gaskets on it and not a high mile engine except for oil the consumption. Why did it have valve interference on only one side, I guess it's a mystery engine. BTW, why no oil filter? Don't reply JiffyLube.
@@kiiiisu If it's obviously my fault. Yes.
@@robertklein1316 Well, unlike you, I'm not perfect. Thanks for the comment Richard.
You got that right!@@gwick358
Your videos have shown me just how complex engines are and how many intricate castings are included.
Don’t split the case haves on that short block. That short block is definitely worth some money. It’s ready for the IMS upgrade. What a great tear down. Loved every minute of it.
I do this exact job EVERY day at work. Absolutely love my job. I've tore down probably 30 of these engines and they can be a pain sometimes. Granted I dismantle or pallet up engines to be sold as a used engine Assembly. I Bielefeld we have 3 entire assembly for this engine and probably another 10 short blocks sitting on the shelves. They usually sell withen a month. A lot of the Porsche engines I've dismantled with higher mileage tend to have cylinder walls that have been torn and also the piston skirts have the same tearing marks. Some of the range rover engines have a similar tendency.
Even though I knew no Porsche water pump was gonna be thrown across the workshop, I had a sneaky suspicion you’d still sneak in a pump toss somehow, even if it was from a different engine. 😆
He should have tossed that water pump. It's junk and needs replaced every 50k miles or so. Plus it's dirt cheap
I like that you didn't pull the short block apart. You already found why it was a core. The whole "bottom" (what is that called on a boxer?) is in great condition, it hurts as a car guy to take apart something that works. I know you went to profit because you are a business, and I also remember you saying you hate taking apart something that's working. I appreciate that there will be some back-blow from people that just want to see a complete tear-down of this engine so justifying for the business needs to be emphasized when I'm confident that it being a working bottom is a great reason to stop there for anyone who has worked on engines before.
As always, I enjoy your videos, good health and good fortunes to you and yours.
notice that there where any witness marks from valves touching the pistons on the second head removal ? Make you wonder if the loose cam gear bolt was the cause of the valves touching pistons ?
Yes, you stopped at the right point. I have a 1965 911 and It's amazing to see how far the 6 cylinder Porsche has progressed. I thought the cam chain setup was simpler than other engines you have torn apart.
It's Saturday time to look at an engine
Don't apologize for the video. Seeing the architecture of this engine was, in my opinion, well worth the lack of carnage. Another excellent video sir.
Completely agree with your choice here. It was cool to see as far as it went, but no sense destroying something you can make money on.
I like how you use that jointed ratchet. I never thought of using it's jointed ability as a speeder handle 🤔
Thank you for this Erik!
So what about that M28 from that 928 in your inventory....
I enjoyed this tear down. The engine appears to be a solid design, IMS notwithstanding. I'm a diesel guy, and a fan of iconic diesel swaps. I'd love to see you tear down an OM606 or TDI engine. These don't fail very often, but have some rare issues folks might appreciate viewing.
The 606 is fairly rare in the states, might be tricky to source.
It could still have damage in the short block due to IMS bearing failure. In which case it's got to come apart assuming it's repairable, even if for no other reasoni than a thorough cleaning to get the metal bits out. I was really hoping to see the exploration of the IMS bearing and shaft.
Iirc the Intake cam isn’t staked on this engine. The central bolt can loosen over time (or not torqued on previous repair) and it will eventually lead to misfire faults. If you don’t catch it and drive home the bolt comes out too far and will prevent the cam from spinning. The loose cam sensor was probably the diagnosis and they assumed (incorrectly) that the cam had broken.
highly reccomend getting a strong neodymium magnet so you can hold it near the oil drain stream. for really f**ked motors the stream will arc towards the magnet.
Pretty good idear!
Thats how every engine should be built! Loving the top end! Its like a high performance bike engine
Ummm...did you miss the part where he said it was a core? Based on the comments It failed due to bad design.
Applause Applause...think you made the right decision--no need for an apology. You do run a business, I'd rather you make the correct decision for your company and your employees...
Good call not tearing down the short block, as much as I would have liked to see it. It was really interesting to see this video, even though you didn't tear it all the way down. This engine looks like it's in very good condition and it should be possible to rebuild it, even considering the intake camshaft. I hope you do really well on this engine, because you deserve it.
As long as there's a water pump toss, I don't care what engine it's from 😂
Hey, no worries. Business is business, and nobody wants to work for a loss. It was more than worth it, to watch that engine come part as far as it did...👍👍
It’s amazing how complicated and intentionally difficult to service these engines are, especially considering Subaru had a similar displacement engine (3.0 vs 3.2) with similar power (250 vs 258) starting at around the same time (Legacy 3.0R was available starting 2004 in Japan) but it was smaller, more reliable and *much* easier to service.
You should see the 928 motor. All aluminum and weighs more than a big block.
The Subaru H6 WAS NOT easy to service. I had the misfortune of having to do timing chains on one. Much like this engine, the entire powertrain had to be dropped. Even spark plugs are right against the frame rails on both sides of the engine bay. Granted they are one of the more reliable Subaru engines but that’s because there’s nothing to them.
That's the power of German engineering.
These things were made during a time when Porsche was in bad shape financially, so they had to cut costs by reusing the same head casting for both sides. That's why there's timing chains on both sides of the block.
Keep in mind the Boxster S 3.2 was intentionally tuned very conservatively so it wouldn't interfere with the base 3.4 911, and that 260hp figure is for the EZ36, not the EZ30 (which made 220 or 240 depending on the year).
@@JohnEvans-ct6mzmight want to try reading. I said the EZ30 was *easier* to service than the M96.
hi I had a similar case on the same engine, my client had over-revved the engine which took a lot of rpm and the valves met the pistons, the same screw on the camshaft was loose, nothing broken, we have completely overhauled this engine, with new chains and shoes, connecting rod bearings and bearings, seal valves, and since this event it has already covered 30,000 kms without any problems.....
Considering it came from a porsche - this is likely the 8th or more time it’s been removed from the car.
You don’t know anything about modern Porsches apparently.
true dat!
Pretty ignorant response I think
Modern Porsche are extremely reliable, apparently.
why ? you have to remove the engine alot of time to work on these cars@@christopherjones2557
Thanks for another great video Eric! You did the right thing stopping where you did. Cannot wait for the next video.
Whats the difference between Elon Musk and a lemur?
Elon Musk made an electric car.
Lemurs Madagascar.
Im so happy you didnt tear down that engine completly. It was hurting me to watch that engine teardown as the engine was in a very good condion. Hope somone rebuild that engine. Hope we will see some destroyed Porsche engine one day. Thanks and here's the like nonethless.
You do have a business to run and profit is definitely a good thing. Smart move on your part to end it where you did. It was interesting to see how the engine was put together. Thank you for that bit of it. Take care.
For bore scoring- the 2.5, 2.7, and 3.2 do not suffer from bore scoring as much as the 3.4+ motors to
Where else in the world can you see complete tear downs , your pick! Lots of thanks.
One of the simplest engines, 1.1 Opel from a GT.
Thanks! Been waiting for a while to see a good M96 teardown! Love my '99 996 C4!
Of course there are some differences between mounting in Boxster and 911. In Boxster the engine is mounted right in front of the rear axle and in 911 it is mounted right behind the rear axle.
Bought my first LBZ Feb 2006…drive it 629,750 kms - then was stolen Jan 2023. Bought an 07 LBZ CCSB SLT. BEST motor, great trucks.
Bypass Oil filter, Titan Tank, FASS….all 3 liberated from found stolen n smashed up 06 truck…
You approach that engine like it's the relics of some Saint. Killin' me.
Well done and i appreciate leaving the short block unmolested. Just that one intake cam...head scratching here.
Taking care of the business never a poor choice. Thx Eric.
I've always stuck with Metzger engines in 911's. For a reason!
Yep. I considered multiple options before choosing my 997 1 turbo. After researching the issues with the m96 and m97 I would never get one
I was all looking forward to seeing inside the short block, but like you said, tearing apart a good bottom end is a good way to lose money.
That's what she said......
I look forward to your videos every week and always learn something, thanks for doing what you do!
After consultation I understand why you didn’t tear the short block down thank you for explaining.
Love the respect he shows by changing his gloves
I enjoy watching Eric's work. A+
It was fun watching you be so gentle with this engine.
Watching while sipping on my morning coffee on a beautiful Sunday
IMS issue is cars that were rarely driven and in salt air climates. A garaged engine that is routinely driven is not a problem. The IMS bearing itself is sealed, but the seal pops off. Then the bearing gets splash lubricated and remains fine unless it gets exposed to air and moisture, because it's metalurgy is intended for it to remain sealed. Best way to counter the corrosion issue is by using HD diesel oil, like Rotella or Delvac. In extreme cases you can use a marine oil.... LiquiMoly makes some if that helps.
At some point before the 2nd head came off, I was thinking "That's a good short block" so it came as no surprise when you stopped after pulling the heads,
No need to apologize for not ruining a factory original Porsche short block. Nice video.
No need for the apology, you’re a business and as much as I love you tearing an engine down to the last nut and bolt you don’t need to do that to your financial detriment just to appease the masses😂 I look forward to you getting a GT3 engine in for a tear down
I was captivated at this video as it demystified disassembly of a Porsche engine. I'm a novice, and this is a novice question I guess: Is this an engine you intend to part out? Why wouldn't you replace / repair the head and damaged valves and reassemble the engine? You said many times that aside from the head/valves the engine was in good shape. Thank you. Best youtube video I have seen in months.
You have got to pull the rod caps on the sidethat crashed the valves on the boxter why did they hit ,cam phaser or rod clearences, it would drive crazy until i checked.
Keep up the good work i enjoy your teardowns
BMW toss at the end made my day! Thanks Eric!