My fortuner 2021 has this engine. May i know what's the problem of this engine that you'd rebuilt? So i can have preventive measures since my car engine is less than 4k km. And does all this model engine will have to be rebuild? Or just some cases?
Thank you very much for your comments,This engine is a very successful engine but the engine I am working in only had its pistons damaged due to the spark plug not being good so its short block has been replaced
Damn I just watched this most excellent video for over a hour and a half 😳 Thank you very informative. Last time I rebuilt a engine we used cork gaskets on the sump and rocker cover
This was very interesting. Thank you. I was wondering what those threaded holes on the side of my engine were for. I see now they are for lifting hooks.
Hello. I am stuck getting the timing cover on. I am trying to like that crank arrow with the timing cover one and I’ve been stuck in this for a while. I can send you pictures but is there any advice you could give?
@@MayoCarsDR just need help on how to actually like the oil pump key that goes to that crankshaft key. It feels like It’s stuck and I try to line it up and it just feels like in the middle it wobbles left and right like it’s not sliding on how it should. I took a couple bolts off of upper lower pan to try to get more leverage. Im really stuck I am heading there tomorrow morning if you have any advice please let me know thank you for your time
Nice video, i have bought fortuner 2022 model with 2TR engine my car is hesitating while acceleration, rpm is not going above 2000, after long press engine is getting power like drift and again getting down with no pickup, engine is vibrating and unable to run smoothly. There is no trouble codes in the computer, Pls pls advise what is the problem
Nice video but problem is the person who is taking video doesn't write the name of each part that are connected to the engine so that us who are still learning can be able to differentiate them by their names
Thank you for the video. I drive 2011 Toyota Prado with 2TR-FE engine. Engine is building up knocking/clapping (chack, chack, chack,...) sound which is very noticeable at cold start and at low rev between 1-1.2 rpm. When engine warms up it becomes milder, but it is always there. Generally, the engine sound is getting rougher. What could it be? I do live in extreme temperature region and I do start the car often, but not always, in very cold. I change the engine oil every 5000-6000km and use mostly 5w-40. Odometer is 100,000km. Thank you very much.
In North America the engine oil for the 2TR-fe is 0w20 full synthetic or 5w20 standard oil..abused it will get a minimum of 250k miles with taken care of examples getting 300k to 500k miles and with some even getting 700k to 1 million miles on the original engine..
@@dlee8835 Toyota owner’s manual for Toyota HiAce with 2TR-FE motor the correct oil grades can be 5W-30 and 10W-30 Energy -conserving and 15W-30 or 20W-50 SL or SM multigrade oils! For those who want fuel economy the energy-conserving is the lighter grade oil.For those who want to long life from their engines I would suggest using the heavier grade oil for hotter climates or harder working conditions!But this is just my opinion as I never use light grade engine oil in my part of Australia.Page 201 Toyota HiAce owners manual gives the climate temperature range and 20w-50 can be used in this engine from -7 to over 40 degrees centigrade.Light oil is given for very cold countries and lower fuel consumption,lower fuel consumption blah blah blah engine wrecking BS for people who trade their vehicles before the warranty runs out!
Thank you for the video. I drive 2011 Toyota Prado with 2TR-FE engine. Engine is building up knocking/clapping (chack, chack, chack,...) sound which is very noticeable at cold start and at low rev between 1-1.2 rpm. When engine warms up it becomes milder, but it is always there. Generally, the engine sound is getting rougher. What could it be?
Y otra cosa que esta mal nunca deben de girar el motor en contra de las manecillas del reloj, especialmente recien hayan colocado ya sea la cadena de tiempo o la banda de distribucion.
Sorry, don't like the way you are lapping those valves in. You're getting uneven coverage as you lap the valve because the valve is bouncing up and down on it's seat. You can buy valve lapping tools very cheaply. They have a suction cup on each end for different sized valves and you can apply even pressure from above instead of spinning the valve from below.
Todo mecanico profesional tiene que usar guantes., no entiendo por que si usan gasolina y oros quimicos o susbstancias como silicon etc, no usan guantes. muy mal
![Felix "Unfair" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/Oswujxm2Ag0/mqdefault.jpg)
![I.N "HALLUCINATION" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/n5B5q1Hwt_U/mqdefault.jpg)
My fortuner 2021 has this engine. May i know what's the problem of this engine that you'd rebuilt? So i can have preventive measures since my car engine is less than 4k km. And does all this model engine will have to be rebuild? Or just some cases?
Thank you very much for your comments,This engine is a very successful engine but the engine I am working in only had its pistons damaged due to the spark plug not being good so its short block has been replaced
How do you test/check the cylinder head for hairline crack that is not visible to naked eye?
@@MayoCarsDR spark plug not being good? what does that mean
That's an excellent work done there. Very informative.
Thanks for comment
Excellent rebuild!!! See if you can add some more captions to parts replaced. Good video.
Thanks for coments
Damn I just watched this most excellent video for over a hour and a half 😳
Thank you very informative.
Last time I rebuilt a engine we used cork gaskets on the sump and rocker cover
Thanks for comment
I did not see spark plug part number, excellent job
This was very interesting. Thank you. I was wondering what those threaded holes on the side of my engine were for. I see now they are for lifting hooks.
Yes, thanks for comment
This is the engine in my 19 tacoma tss off road 👍🏼
Thanks for comment
Hello. I am stuck getting the timing cover on. I am trying to like that crank arrow with the timing cover one and I’ve been stuck in this for a while. I can send you pictures but is there any advice you could give?
What I can help you
@@MayoCarsDR just need help on how to actually like the oil pump key that goes to that crankshaft key. It feels like It’s stuck and I try to line it up and it just feels like in the middle it wobbles left and right like it’s not sliding on how it should. I took a couple bolts off of upper lower pan to try to get more leverage. Im really stuck I am heading there tomorrow morning if you have any advice please let me know thank you for your time
Thank you for the video! Will you be able to help me with the engine manuals.
Yes i can help you
Nice video, i have bought fortuner 2022 model with 2TR engine my car is hesitating while acceleration, rpm is not going above 2000, after long press engine is getting power like drift and again getting down with no pickup, engine is vibrating and unable to run smoothly. There is no trouble codes in the computer, Pls pls advise what is the problem
Check fuel pump pressure
Check fuel injectors
Check spark plugs
Quá tuyệt vời anh ơi chi tiết phải như này mới hiểu
Hello and thank you for this video. May I ask why you put silicone on the corners of the head gasket?
Because this is where the head and short block are joined and later most of the oil leaks from here, so this is where the seal is installed.
@@MayoCarsDR Interesting. Thank you very much!
I live in Cali. I’m researching you ASAP
Nice to see‼
Nice video but problem is the person who is taking video doesn't write the name of each part that are connected to the engine so that us who are still learning can be able to differentiate them by their names
Ok
Thanks for comment
I will try
do you know if there is a difference in the block between a single vvti and a dual vvti?
There is no difference
I ask because I plan to rebuild a single vvti block for lower cost and use my dual vvti head, thanks!
What is the minig of hold
Thank you for the video. I drive 2011 Toyota Prado with 2TR-FE engine. Engine is building up knocking/clapping (chack, chack, chack,...) sound which is very noticeable at cold start and at low rev between 1-1.2 rpm. When engine warms up it becomes milder, but it is always there. Generally, the engine sound is getting rougher. What could it be?
I do live in extreme temperature region and I do start the car often, but not always, in very cold. I change the engine oil every 5000-6000km and use mostly 5w-40. Odometer is 100,000km.
Thank you very much.
Thanks for coments,2TR is a very successful engine and your car has not traveled many km there will be small problem
It’s 5w20. Not 40 weight use manufactured specs
In North America the engine oil for the 2TR-fe is 0w20 full synthetic or 5w20 standard oil..abused it will get a minimum of 250k miles with taken care of examples getting 300k to 500k miles and with some even getting 700k to 1 million miles on the original engine..
@@dlee8835 Toyota owner’s manual for Toyota HiAce with 2TR-FE motor the correct oil grades can be 5W-30 and 10W-30 Energy -conserving and 15W-30 or 20W-50 SL or SM multigrade oils! For those who want fuel economy the energy-conserving is the lighter grade oil.For those who want to long life from their engines I would suggest using the heavier grade oil for hotter climates or harder working conditions!But this is just my opinion as I never use light grade engine oil in my part of Australia.Page 201 Toyota HiAce owners manual gives the climate temperature range and 20w-50 can be used in this engine from -7 to over 40 degrees centigrade.Light oil is given for very cold countries and lower fuel consumption,lower fuel consumption blah blah blah engine wrecking BS for people who trade their vehicles before the warranty runs out!
Thank you for the video. I drive 2011 Toyota Prado with 2TR-FE engine. Engine is building up knocking/clapping (chack, chack, chack,...) sound which is very noticeable at cold start and at low rev between 1-1.2 rpm. When engine warms up it becomes milder, but it is always there. Generally, the engine sound is getting rougher. What could it be?
ruclips.net/video/gwJ5BBHb9W4/видео.html&ab_channel=speedkar99
I'd say these are you bearings , probably time for a rebuild , do it early before it gets nasty
Mine had low power, started knocking. Only 60 lbs of compression in 1 and 2: Blown headgasket.
Buen día compañero. Cuál sería el torque en libras pie. De banca y biela
2TR engine rebuild repair Manual
ruclips.net/video/RiygbqEZ2nM/видео.html
هل المحرك هاذا تعرض للحراره لسبب تدبيلك الوجه
Great video. What is your opinion about boosting it with a supercharger by URD? I want a Tacoma 4x4
Thanks for comment,Yes you can but it will take a lot of hard work
Realy That Is Good Job
can you send link for that gasket kit you have? thank you
Gasket Kit, Engine Overha
04111,0C162
2TR-FE 2.7L Dual VVTI
V nice vdeo thkns
You welcome
Excellent 👌
Very nice job
Thanks for comment
Loving it.
Awesome build! Could you let me know how much did you spent gasket, seal, chain and etc? Thank you
Around 400,500$
Y otra cosa que esta mal nunca deben de girar el motor en contra de las manecillas del reloj, especialmente recien hayan colocado ya sea la cadena de tiempo o la banda de distribucion.
No problem
Very Very nice
Thanks for comment
You sick af bro
Why bro
Nice
Thanks
Красавчик
Thanks for comment
Я тоже разбираю Таиота Хаилюкс 2016 года хотел крышку переднию открыть походу с низу четыре болта держит
Exelente
Thanks for coments
My friend, I want this site that tells you the power of the engine torque, two Newtons 30:14
Perfecto
Thanks
excelente
Thanks for comment
What’s with the ding ding noise?
Wow
Sorry, don't like the way you are lapping those valves in. You're getting uneven coverage as you lap the valve because the valve is bouncing up and down on it's seat. You can buy valve lapping tools very cheaply. They have a suction cup on each end for different sized valves and you can apply even pressure from above instead of spinning the valve from below.
Ok
Thanks for comment
omg 😭🔥 !!
Ok
Todo mecanico profesional tiene que usar guantes., no entiendo por que si usan gasolina y oros quimicos o susbstancias como silicon etc, no usan guantes. muy mal
Thanks for comment
Where is oil switch
Thanks for comment
Check this video
ruclips.net/video/Zg8xlYJPtCs/видео.html
this engine on my fortuner 07 too bad ,underpower and fuel cons horrible really not for saver family option
Запчасти нужно меня
Можно парускы напишу
Yes
Interesting ive never seen someone reseat valves from underneath
Thanks for comment
He only uses gasoline to wash his hands! 😲
Let’s be friends
You welcome
Nice
Thanks