2.94g, Supermicro RC Plane 만들기 (3Channel)
HTML-код
- Опубликовано: 26 сен 2020
- * Specification
Fuselage : Styrofoam & 0.5mm Carbon rod
Wingspan : 115mm
Motor : ∅4 x 8mm Coreless Motor
Receiver : 2.4Ghz Super micro 4ch receiver
ESC : -
Actuator : 2 pcs
Propeller : 29mm
Battery : 1Cell 20mah
Transmitter : 2.4Ghz Transmitter
Flying Weight : 2.94g (Flying weight, Including 1Cell 20mah Battery)
Flight time : -
* 2.4Ghz Transmitter & Micro 4ch receiver & Micro actuator & 1Cell battery... and so on...
www.Drcmall.com
www.MinimumRC.com
* ∅4x8mm Coreless Motor
www.aliexpress.com/item/32871...
* 1Cell 20mah battery
www.aliexpress.com/item/40006...
* 스티로폼 열선커터기 만들기 (초소형 비행기 & 미니어쳐 제작용)_Heated wire Foam Cutter
• How to make a Hot(Heat... 
Хобби
![NoCap - Yacht Party [Official Music Video]](http://i.ytimg.com/vi/rm_lvDln8kE/mqdefault.jpg)
WOW! Never knew about these magnetic actuators. Excellent instructional and informative video!
Thank you... Have a nice day...^.^
It's relaxing and tense at the same time to watch and I guess to build as well. Bravo.
Thanks Bro...^.^
This should have more views, awesome build
Thank you...^.^🙂
Try gearing your motor so you can use a bigger prop. Your target weight should not at least exceed 3.8 grams and that will fly. I made a tiny Spitfire years ago weighing 3.8 grams out of durobatics foam and Plantraco 2 ch system with a 30 mah lipo battery, a 4 mm pager tail motor from an IR toy helicopter. Yours will fly.
In the first place, the goal was to make less than 3g, so the gear system was not considered.
But, I will try again soon... Thanks for your advise...^-^
Impressive really ! Congrats. You could have saved more by direct board soldering saving on 6 connectors/6 soldering points + 2 connectors for Lipo bat + simple wires and 2 soldering points for lipo. 0.2 to 0.4g to my calculations.
Thanks for the advice. Have a nice day today...^.^
any micro rc receiver connect rc transmitter ??????
It's not like that. Each receiver and transmitter must use products with compatible protocols. Most products (transmitters & receivers) produced by the same company are compatible with each other...^.^
Maybe u should use 720 motor
I think it's too heavy... will it be ok?...^.^
@@creativechannel9368 Bro are you on insta cuz i want to show something
@@creativechannel9368 I made a plane like u but i don't have motor but I have small battery 😂
👏👏👏
Thanks bro...^-^
Where did you buy receiver
Information is provided in the comments section at the bottom of the video above...^.^
* 2.4Ghz Transmitter & Micro 4ch receiver & Micro actuator & 1Cell battery... and so on...
www.Drcmall.com
www.MinimumRC.com
👍
Thank you...^.^
What time of reaceacer did you use that's can bind on the fly sky?
I don't understand what you're asking.
What does 'reaceacer' mean?
@@creativechannel9368 micro reaceaver the board that I can bind whith fly sky fsi6 transmitter for ultra micro planes
@@MarkJimenez-dw1tl
Oh... I understand now. Are you talking about Receiver (2.4Ghz Super micro 4ch receiver)?
The above transmitter and receiver were purchased from a Korean RC shop.
I am not sure if it is possible to bind it with your original FLYSKY transmitter.
I think a safe binding will only be guaranteed if you purchase the transmitter and receiver from the same place...^.^
Can you give me an exact US link where to buy the actuator at did you make it
Hi, brother... for your questions, please refer as follows...^.^
* 2.4Ghz Transmitter & Micro 4ch receiver & Micro actuator & 1Cell battery... and so on...
www.Drcmall.com
www.MinimumRC.com
Con una ala con perfil curvo te resulta mejor
Oh, I see... Thanks for the advice...^.^
some late information. that motor may not be powerful, enough. however, there are some OTHER things to contemplate. the shapes of wing and stabs sucks. on a model this size, the use of outboard dihedral results reduced efficiency and roll-axis stability. the area of control surface areas are Small, with NO associated reduction in Mass. because the wing has a zero-lift profile, ALL lift must come from positive aoa. angle of attack. i have details, if you want them. cheers googletranslate
Thanks for your help. It will help me a lot in the future. I'll try a little more... Have a good day...^.^
Agreed. 0 lift wings compensated by aoa so more drag. Is it possible to shape the wings profile with hot air blower ? Making a positive lift with small drag.
Hey can you please tell me what the receiver is called?
For your question, please refer as follows...^.^
* 2.4Ghz Transmitter & Micro 4ch receiver & Micro actuator & 1Cell battery... and so on...
www.Drcmall.com
www.MinimumRC.com
not good..
what do you need?
answer: big wings
Thanks for your opinion...^-^
.
미니rc비행기만들때 팁좀요 ㅠㅠ
미니 RC 제작시 가장 중요한 점 이라면, '비행중량의 감량' 이 아닌가 싶습니다.
기본 기자재들 구입시 각 부품의 '무게'를 철저하게 확인을 하셔야 합니다. 그 다음으로는 '무게중심(CG)' 가 될듯 하네요. 큰 기체에 비해서, 기자재들을 배치할수 있는 위치가 제한적이다보니 많은 고민이 필요합니다...^-^
@@creativechannel9368 감사합니다
Motor does not high rpm
Yes... it could be... Thanks...^.^
怎么没飞起来，动力不足么……
Yes... I thought that if I had made the wing area of the wings a little bigger, I would have been able to fly better...^.^