I have the same screen protector and don't have that ring that is in your video. The video included is actually shorter then a version of the same video that I've seen in the past for my S21U. That instructional video is a lot better. Also you skipped a few steps like wiping down the phone before curing the sides. You want to get rid of any excessive glue before you really cure it fully. My FPS works flawlessly as well as if it it didn't have a screen protector on it. Also you might want to push your tilt the point towards the top so that the glass will reach as far as possible to the top so that there is enough clearance for the glass to fully cover the actual viewing screen. The bottom has more bezel area then the top so it's more forgiving but you need to make sure the top is as high as possible. It should be even top and bottom if you did it right.
I watched this video and bought the screen saver. Just follow the video and the application is flawless. Put three quarters on the weight. Finger print scanner has no issues and didn't have to re recognize them or up sensitivity. The excess cleaned up very well. Can't even tell I have a glass protector on it. Its smooth to touch. Fantastic product. Works with my renke hybrid case. Doesn't pull up corners. Just make sure the screen protector stays centered top to bottom. It moves with the glue order it till it cures with blue light.
I learned my lesson.. Use a case and a screen protector, phones are too expensive to be breaking or scratching them. Also, it helps to have them in good condition so when you want to trade in your phone you get a higher value for it.
I recommend not use the metal weight with the light for no more than 10 seconds or else you'll see a small dent in that area of the phone. It happen to me while installing it.. But the screen still looks great, no scratches on my phone yet.
I followed the video. Everything worked great. Finger print is slower but still works. I was so pleased that I was able to deploy without bubbles. After about two hours a small bubble appeared in the middle of the screen. I don't want to pull up the cover so I guess I will live with it until it is time to replace the screen cover in 6 months or so. This video is a great tutorial for installation.
*Thanks for the tutorial. I kept reading about people saying "watch the video first before installing". I'm here thinking... what video?? I guess your video is THE video. lol*
Great video! I have the same product. One piece of advice: If the fingerprint sensor doesn't recognize your print after installation, before adding more weight and curing again, try recalibrating your print. For lack of a more technical explanation... Because of the new/extra layer, your print is read as slightly different from the original calibration.
So you mean once I put the liquid on and lower the screen protector on the screen I have to recalibrate the fingerprint before curing the first time? Or do you mean to cure it without the weight then register the new print then finish the curing process.
Got this screen protector before the video was posted; highly recommended. I agree, very clean install and very hard to see it is even there. I will say that the fingerprint scanner does not always work and I have to press a few times to get it to work, but overall very happy
@@Fronzel.Neekburm it was pretty strong during insulation and after curing, but the next morning I didn't notice it anymore. But, my nose is not super sensitive, so it might have smelled a bit longer. But, I didn't get any complaints from those around me
I epoxied the flapping UV light's legs in place since they don't snap into place (for standing).😬 Probably not really necessary but it was a way for me to procrastinate another day (or week). Still paranoid about this installation with new-phone-nerves.😐
I had a huge bubble the size of a big peanut smack in the middle right where i dripped the glue. And two bubbles on the sides. I was like OMG. I pushed the big bubble out pressing it up and out from the top using the dry soft cloth. And did the same with the other two bubbles. I cured it and scraped off all the glue that was pressed out on the top if the phone. Looks great! Perfect install. I was thinking I wasted a screen. Shew! Fingerprint and S Pen work perfectly!
I bought this last week. took 2 times to get it right, but I am happy with the results. I dont use the fingerprint scanner, so next time I think I will skip the weights.
Hey great video. Is the circle around the fingerprint visible in normal use? Or is it more of an off axis kinda thing? Also does it disappear or goes less visible after a few days? Thanks a lot.
Never used this product, but Whitestone done has the same thing, and they have zero marks like this. When ever I did mess up and cure, the imperfections are visible till you apply a new one. Seems like this is to get a closer contact for the fingertip..
Hey guys thank you for your responses. I never did a follow up on this but I ended up buying it. Definitely worth it. The circle is there but it's barely visible and you can only see it at steep angles when the screen is off. If anyone is worrying about this as I was, don't.
Great content. I believe I told you about that screen protector when I used it on my note10+ we'll. I stopped using full adhesive and edge adhesive glass screen protectors. I use the supcase unicorn beetle pro cases for my note20 ultra. And every time I switched out, my case for a different color one, the screen protector would lift. So now I use the Amfilm elastic skin screen protector. It works flawlessly with all my cases; it doesn't feel rubbery. I've had it on for 6 months now and still look like I just put it on. And it was only 9 bucks on ebay.
@@jeromegold3216 thanks a lot, I am waiting for my s22 and getting equipped with cases and screen protectors.... for me something like the one pre applied to s10/note10 series is pretty decent despite getting scratches easily... I had bought two white stone dome glasses for my old galaxy note 8 and one I had to remove because it got ruined when at service center... the second one didn't match the spigen cases...(many bubbles at corners).. do I got fed up with these glued tempered glasses.. they cost a bomb and not even sure they match the cases you wanna buy
@@jeromegold3216 spigen liquid air... very cheap and nice... Good radio price/quality... I like the transparent one.. but it turns yellow and it doesn't have a camera cut-out for each sensor
Hi i just want to warn you about somthing very importatn I failed to install the first two screen protector so i left with 2 and unfortuntly i failed to install one of them so i left with one screen protector i was very carefull when i was installing it i watch "YOUR" V video in the last attempt and i figure out the problem YOU MUST PUT THE BOTH BUBBLE OF THE AD LIQUID AT THE " BOTTOM" DON'T PUT IT LOW VERY MUCH just in the first quarter from bottom, and also make sure you don't make bubbles while pouring th ad liquid itself Your video really saved me from spending more money in such things THANK YOU SOOO MUCH🧡🧡🧡🔥🧡🧡🙏🙏🙏🙏🙏
The screen protector tabs that you pull to release the film don't work, I used all of my protectors trying to get 1 to pull off, just the sticky tabs came off so I had to scrape a corner off with my fingernail to get a corner up to pull the backing off. PLUS..." Do Not Get This Adhesive On Your Skin!" I must have gotten some of the adhesive on my fingers and I scratched my forehead, half hour later it still feels like it's on fire.... I can't even imagine what would happen if it was on your finger and you rubbed your eyes. The glue can't be squeezed out of the bottle, the bottle is to thick so it sort of dribbles out even with top cap off so it's takes a minute for all the adhesive to come out, meanwhile, dust is getting on the screen.
its gorilla victus + and we have to go through all the steps for covering its screen. dont mind spending xtra cash samsung, just put it the screen protector like note 10+ when we buy it
They say phones are so scratch resistant nowadays but I always get a bunch of little scratches all over the screen still. Even after having the S22 ultra for a week and treating it like a baby.
Gorilla doesnt protect your screen from scratches, it just protects you from a drop so your screen doesn't go to hell. And if I'm buying a $1,700 USD phone (that's its price in Mexico), I don't mind buying a premium tempered glass protector.
@@viktord.8018 Thanks so much for the response.. I just tested Taking couple of pictures without the tempered glass and just placing it on top without actually applying it. I got significant difference. So thought to check with you. And, is it ok if the glue leak to the bottom portion of the phone? Because, it has a tiny gap between phone and the silver rail.
@@karthikeyans8922 just make sure you cover all the holes, so glue doesn't get in them. Especially on the bottom. On my application I noticed I may have added a bit too much and it ran on the bottom, had to scratch it off.
Worked great on my S22 ultra but I had a good size bubble near the middle of the screen,, so I gently worked it to the edge until it disappeared,, before I used the UV light to cure it. Worked great
In my opinion I thought it was much cheaper than the whitedome but it is worth the same and in my opinion the white dome is a better option and brings more accessories that make your work easier and the footprint works perfectly that is my opinion
My installation was going great until I bumped the guide against the glass, so now I have a small bubble on the screen. Minor inconvenience, but it still can live with it. Excellent tutorial nonetheless!
Great video, I've seen reviews for most all of these Double Glue Puddle Type Protectors to only put 1 Glue Spot for much better luck without getting air bubbles, etc. You did a great job. My problem is, I have a dusty house & by the time I clean the screen, add the glue, I'm already getting dust on the phone. I'm curious how these work with a case? I've been using Self Healing TPU Screen Protectors & they only last a week or 2 before getting sticky, peeling up, dust collecting around the edges, etc..
Do it in the bathroom with shower steaming up the room, it will drag the dust down out of the air. Keep in mind this glue stuff is a bit toxic, don't want to breathe it long. Got on my clothes and left a burn on my skin for a few hours.
What is the proper way to remove dust or lint from under the screen protector after application? In my case, the lint was black and I didn't see it while the screen was powered off.
Great video. I watched this and the manufactures video and still messed up my first one. Had air bubbles and tried to squeeze them out which made a right mess. I had to take it off, wipe the whole phone and start again with another set. 2nd time, I noticed I had more gap on the top than the bottom, left that for now. I only had 3 with my set, so got 1 left now. I have noticed the figure print sensor isn't as quick as before. But still not that bad. Fits with my original Samsung clear kickstand case.
Can't say my experience is the same. I have done two installations. Both had lift in the corners one I inserted the phone into its protective case, an i-Blason Ares.
The fingerprint IS an issue with this one for 2 reasons. The glass is thicker than most glass protectors. The area on the protector intended to be on top of the sensor is off center and only half covers the sensor.
Some how I did mine and it didn't leave a ring at all 🤔. Well probably because I didn't let it sit as long as he said with that weight on it, because I didn't want that ring on it like every video i seen. Anyway, It definitely didn't register my finger prints at all 🤣. I had to redo them, but it works fine now and no ring at all, thank God 🙌🏽
I have the same screen protector. Mine doesn't have a ring like that at all. I'm not sure what he did to cause they deep of a ring as the video was edited I believe cause he talked later on about putting more weight on that area which is not needed. I think he put too much weight or so and that's why that area is like that. I would say the less glue you have in-between the bigger it will come out and the FPS will be more effective as well. Mine works just great like as if it was stock. He did skip a few steps though cause I would recommend deleting all of your old fingerprints and rescanning them again.
Great video, but i wish someone would mention the obvious for us stupid people: MAKE SURE YOUR WORKSPACE IS LEVEL! It's hard to find a space in a house with 3 cats where fur isn't omnipresent, so I used the top of the washer for a table. It wasn't level and some of the "glue" ran off the side and, hence, there wasn't enough for a perfect installation. I'll use it for a few months and give it another go later. Glad there are 3 in the pack!
Since there is no camera hole cut out I would like to ask, does the screen protector affect the selfie camera quality? I'm considering buying this and would like to know about the concerns I have with it.
Hi. Many thanks for the instructive video. Although I've followed step-by-step the procedure in the video it ended up with a couple of bubbles. But, something that is bother me a lot, is it normal that after 2 days of having installed it the smell coming out of the glue is still reeking? I can feel it everywhere which is not good.
It should not be leaking. I would suggest putting the phone under the light and continuing to wipe it down. The allotted time for the light per the directions is not long enough. I would try another few minutes at minimum.
This time was a re-application so I came back to your guide. The screen protector did its job! I dropped my phone onto a metal table foot and the screen protector shattered, intact, but my screen underneath was perfectly fine. The old one came off easily enough and there were no little pieces of glass coming off it.
Hey... Just noticed that the weight included with this kit has a fine ridge around the outer edge (on both ends you can catch a fingernail on it)... I easily filed it off. Might make the ring less noticeable after the install?🤔... Hmmm. Not sure if I even want to lock my phone at all at this point!😐
You don't really want another layer of glass in front of the camera because the pictures don't come out looking as good as without. It blocks the light and sometimes it shows sun flares too
@@kokopuffs5789 I have a realme GT with tempered glass covering the front camera and had no issues with it, ofc it blocks the light when the glasss is dirty, but common, just clean it
Just installed worked great. But when I scan Qr on box of product it said do not use USB c to usb c cable. Says it will not work.whats up with that. Mine did
I tried it and worked wornerfully untill 2 days later. There is a big bubble showing up at the bottom right cornee. I want to try again. Please tell me what i need to watch out to avoid this issue on my 2nd try. Thank you
I assume it's the same for the Note20 Ultra... (I bought the correct protector already) Are there written / printable (PDF) instructions online anywhere? Also, would it hurt anything to cure the glue longer (by exposing to UV lamp for longer than 45+120+30+30 seconds)? Is there any reason I can't just use masking tape instead of the stickers to cover the ports & orifices at both ends of the phone?
ok so can you redo this install without using the weight.? I know it may possibly effect the sensor reading but I do not like that stupid circle peranently there. if one can install it without the weight does it still work?
I did that on realme GT but without UV tempered glass, and the fingerprint is perfect, so I suppose it will work just fine on s22 ultra because UV tempered glass is even thinner, lol and have more contact with the screen itself
I did a flawless install of the whitestone. It went on and looks perfect..But...fingerprint sensor is now very difficult to use. Probly going to remove the whitestone as much as I hate to.
@@tikkin11 did you adjust your touch sensitivity and re-register your finger prints.i have heard of people having this issue,but all the install videos seem to look like it works.fine.
@@terryeverly5617 I took the first Whitestone off and redid the job using the spare they provide in the kit. Stole an idea here from Mowie and put a weight in the fingerprint area while curing. This caused noticeably more glue to run out from the glass. Finished it up and now the sensor works much better. My conclusion is that Whitestone uses just a bit too much glue, and their plastic "weight" bar is not as effective as it should be. Why some Whitestones work and other don't is most likely related to exactly how much glue is in each tube.
@@chickenfordinner2093 Yes. Those provided side pads get most of it. Followed the Whitestone instructions of short cure, followed by wipe down and long cure. If I was starting over I would go with this Mowei kit.
Does the absorbent pad 100% prevent adhesive from getting in the earpiece speaker? I'm concerned it doesn't get taped over but capillary action should keep the fluid out of the hole if the absorbent pad is there, right?
The foam thingys kinda work but... take the guide strips and cover the bottom holes. Cut a tiny piece off of one and cover the tiny top hole. Just to ensure that nothing gets In The speakers. Also good tip, take your s-pen out when coving the holes for a smoother seam.
First thanks for the video. I had no metal cylinder in my one for the Pixel 7 Pro. All went perfect except 2 bubbles in the center of the screen. I was afraid to take it out before putting the lights but i should have done that i think. Guess i'm obliged to remove it completely now and put another, do you agree ? Thanks
Thank you for your support, are the bubbles small? If so maybe wait until the end of the week and see if they go away. If it bothers you (like it probably would me) I would just take it off and do it again.
@@HighTechCheck it wasn't going away because the light solidifies it I guess. I tried to put another one and there was even more bubbles, driving me crazy not to be able to do anything
I just installed mine today and I didn't leave the weight on as long as he did and I managed not to get a ring on my protector. I don't know how I did it, but I definitely had to redo my finger prints. So I probably had too much glue around the finger print area, because I had to clean it off after getting rid of the bubbles. So that's probably why I didn't have a ring.
I wondered with modern phone of 2022, Gorilla glass Victus + etc, do we even still need a screen protector to begin with ? (Case protector yes, but screen protector?)
Followed every step, even added 2 extra coins on fingerprint sensor. Display looks flawless, no bubbles or dust, but fingerprint sensor is bugging.... It doesnt even want to add new print 😔
I installed two of them perfect no finger print that works. Now my phone smells like that gross glue. Will that smell every go away and can that glue ruin your phone?
You can clean the glue off with iso alcohol, so yes. I'll be reusing one as soon as I take the time to do it. My first install went well but for some reason, after a week, the glue just gave up and the glass started to come off... The cold conditions may be to blame but I'm not 100% sure
With S23U this is the way to go. Others, with adhesive preapplied are quite crappy, so I am back to this. I say it is only worth the prise because competition is lackluster and the end result, when you are lucky is very nice. First one I did worked out great. No defects. Next 3 were failures and my phone is naked for the time being. They need to figure out better repeatability. There really is no way to get rid of bubbles once they form - you will either drain the glue from the top and sides or messing long enough in good lighting the glue dries and gets sticky, by that point it has failed. Anyone owning a high end phone should have better things to do with their time to repeatedly waste it on applying screen protector for an hour and failing. Bottom line: this screen protector as a whole is not a great product. It is the best only because competition is lackluster. And possibly because S23U screen is curved for no other reason than vanity and pain in the ass for screen protection.
I cannot manage getting this thing on without bubbles being left under it. so I'll probably either look for a different, non-liquid adhesive one or go completely without protector
So once you apply the liquid and lower the screen protector make sure both bubbles touch ever so slightly in the middle. Once that happens slowly lower the screen protector the rest of the way and boom you're done with no bubbles.
Ive tried without it and it didnt work at all so I'd say yes. I know how you feel about that circle, it drives me crazy. The glass needs to be as close to the screen as possible for it to work properly.
Need a good way to remove them after installing. I struggled recently to remove the dome one on my Note 10 Plus before I sent it back to Samsung. I almost want to avoid tempered glass on the S22 Ultra now.
Actually yes!! I can speak from experience. I have a kinda deep-ish scratch in the top center of the screen (I can catch a finger nail on it). I followed all of the instructions and you can't even tell there was ever a scratch. If you have very light scratches they'll just disappear.
Cover switches? Package says 9H hardness denoting sapphire. It's not! Same price as Whitestone dome. On one of the android forums, the recommendation is NO.
I had this screen protector for about 2 months. I dropped my phone from about 2.5 feet high and my screen cracked while the "protector" stayed intact. It even popped off of the screen without breaking. I followed the video exactly as shown.
Overall, the installation was relatively simple and the product fit perfectly. I gave it 4 stars due to the effect it has on the front camera. The screen protector rests on top of the front camera, causing images to not be as sharp. I prefer to have an opening on he protector for the camera In Amazon reviews
I put mines on today and I have got lots of bubbles .. like the glue got stuck on one side.. how do I get rid of it. I used 2 already.. does anyone know the email to contact mowei to register the warranty
Level surface, Dunst free environment and make sure the two bubbles touch ever so slightly in the middle. Then just follow the process. If you need a dust free environment try a bathroom. That's what I use.
Have you installed your Dome protector yet? I tried twice, and even put a stack of quarters over the fingerprint scanner area while curing the adhesive, and the fingerprint scanner still does not work well.
If you make sure there are no bubbles in the liquid before you put the screen down you shouldn’t get any. I’ve never had bubbles with any of the liquid screen protectors I’ve ever used.
My phone screen is ruined¡! I had a horrible experience with a s20+. The curves are slightly off on the glass leaving both sides with gaps. Tried it twice with the same result. My screen now has a glare on it! HOW DO YOU GET THIS GLUE OFF!!!!!!!!!! Rubbing Alcohol don't work
никогда так не делайте как на этом видео. как только вы протёрли экран от пыли, не снимайте пленку, откручивать клей и т.д. над экраном, чтоб не попала пыль, волосы с рук и т.д. снова на экран
![Kumamoto Masters Japan 2024 | Gregoria Mariska Tunjung (INA) [5] vs. Akane Yamaguchi (JPN) [2] | F](http://i.ytimg.com/vi/EIjZybhsWqA/mqdefault.jpg)
I have the same screen protector and don't have that ring that is in your video. The video included is actually shorter then a version of the same video that I've seen in the past for my S21U. That instructional video is a lot better.
Also you skipped a few steps like wiping down the phone before curing the sides. You want to get rid of any excessive glue before you really cure it fully.
My FPS works flawlessly as well as if it it didn't have a screen protector on it. Also you might want to push your tilt the point towards the top so that the glass will reach as far as possible to the top so that there is enough clearance for the glass to fully cover the actual viewing screen. The bottom has more bezel area then the top so it's more forgiving but you need to make sure the top is as high as possible. It should be even top and bottom if you did it right.
I watched this video and bought the screen saver. Just follow the video and the application is flawless. Put three quarters on the weight. Finger print scanner has no issues and didn't have to re recognize them or up sensitivity. The excess cleaned up very well. Can't even tell I have a glass protector on it. Its smooth to touch. Fantastic product. Works with my renke hybrid case. Doesn't pull up corners. Just make sure the screen protector stays centered top to bottom. It moves with the glue order it till it cures with blue light.
I learned my lesson.. Use a case and a screen protector, phones are too expensive to be breaking or scratching them. Also, it helps to have them in good condition so when you want to trade in your phone you get a higher value for it.
I recommend not use the metal weight with the light for no more than 10 seconds or else you'll see a small dent in that area of the phone. It happen to me while installing it.. But the screen still looks great, no scratches on my phone yet.
I followed the video. Everything worked great. Finger print is slower but still works. I was so pleased that I was able to deploy without bubbles. After about two hours a small bubble appeared in the middle of the screen. I don't want to pull up the cover so I guess I will live with it until it is time to replace the screen cover in 6 months or so. This video is a great tutorial for installation.
Thank you for the comment and your support Gordon
*Thanks for the tutorial. I kept reading about people saying "watch the video first before installing". I'm here thinking... what video?? I guess your video is THE video. lol*
Great video! I have the same product. One piece of advice: If the fingerprint sensor doesn't recognize your print after installation, before adding more weight and curing again, try recalibrating your print. For lack of a more technical explanation... Because of the new/extra layer, your print is read as slightly different from the original calibration.
Great tip 👌.
So you mean once I put the liquid on and lower the screen protector on the screen I have to recalibrate the fingerprint before curing the first time? Or do you mean to cure it without the weight then register the new print then finish the curing process.
Got this screen protector before the video was posted; highly recommended. I agree, very clean install and very hard to see it is even there. I will say that the fingerprint scanner does not always work and I have to press a few times to get it to work, but overall very happy
@@Fronzel.Neekburm it was pretty strong during insulation and after curing, but the next morning I didn't notice it anymore. But, my nose is not super sensitive, so it might have smelled a bit longer. But, I didn't get any complaints from those around me
WOULD HAVE WORKED ALL THE TIME HAD YOU USED A COUPLE OF EXTRA WEIGHTS ON TOP OF THE WEIGHT THAT CAME WITH IT
I epoxied the flapping UV light's legs in place since they don't snap into place (for standing).😬 Probably not really necessary but it was a way for me to procrastinate another day (or week). Still paranoid about this installation with new-phone-nerves.😐
I had a huge bubble the size of a big peanut smack in the middle right where i dripped the glue. And two bubbles on the sides. I was like OMG. I pushed the big bubble out pressing it up and out from the top using the dry soft cloth. And did the same with the other two bubbles. I cured it and scraped off all the glue that was pressed out on the top if the phone. Looks great! Perfect install. I was thinking I wasted a screen. Shew! Fingerprint and S Pen work perfectly!
Pro tips: place the weight a bit above the sticker, the sensor is there, re scan your fingertip and it should work!
I bought this last week. took 2 times to get it right, but I am happy with the results. I dont use the fingerprint scanner, so next time I think I will skip the weights.
Thanks, that is exactly what I wanted to know. I dont use the scanner either
Hey great video. Is the circle around the fingerprint visible in normal use? Or is it more of an off axis kinda thing? Also does it disappear or goes less visible after a few days? Thanks a lot.
Never used this product, but Whitestone done has the same thing, and they have zero marks like this. When ever I did mess up and cure, the imperfections are visible till you apply a new one. Seems like this is to get a closer contact for the fingertip..
It's not visible at all, i just installed it onto mine today
Hey guys thank you for your responses. I never did a follow up on this but I ended up buying it. Definitely worth it. The circle is there but it's barely visible and you can only see it at steep angles when the screen is off. If anyone is worrying about this as I was, don't.
@@MrJkornd808 WHITESTONE DOME IS DOG SHIT THIS TIME AROUND - PROVEN ALREADY MANY TIMES VS MOWEI
@@HossLUK Hey, how about the front camera photo quality? As it is blocking the camera.
Great content. I believe I told you about that screen protector when I used it on my note10+ we'll. I stopped using full adhesive and edge adhesive glass screen protectors. I use the supcase unicorn beetle pro cases for my note20 ultra. And every time I switched out, my case for a different color one, the screen protector would lift. So now I use the Amfilm elastic skin screen protector. It works flawlessly with all my cases; it doesn't feel rubbery. I've had it on for 6 months now and still look like I just put it on. And it was only 9 bucks on ebay.
How is the s pen feeling?
@Vati it feels good, not rubbery.
@@jeromegold3216 thanks a lot, I am waiting for my s22 and getting equipped with cases and screen protectors.... for me something like the one pre applied to s10/note10 series is pretty decent despite getting scratches easily... I had bought two white stone dome glasses for my old galaxy note 8 and one I had to remove because it got ruined when at service center... the second one didn't match the spigen cases...(many bubbles at corners).. do I got fed up with these glued tempered glasses.. they cost a bomb and not even sure they match the cases you wanna buy
@Vati so what case are you going to get for your s22 ultra?
@@jeromegold3216 spigen liquid air... very cheap and nice... Good radio price/quality... I like the transparent one.. but it turns yellow and it doesn't have a camera cut-out for each sensor
Hi i just want to warn you about somthing very importatn
I failed to install the first two screen protector so i left with 2 and unfortuntly i failed to install one of them so i left with one screen protector i was very carefull when i was installing it i watch "YOUR" V
video in the last attempt and i figure out the problem YOU MUST PUT THE BOTH BUBBLE OF THE AD LIQUID AT THE " BOTTOM" DON'T PUT IT LOW VERY MUCH just in the first quarter from bottom,
and also make sure you don't make bubbles while pouring th ad liquid itself
Your video really saved me from spending more money in such things
THANK YOU SOOO MUCH🧡🧡🧡🔥🧡🧡🙏🙏🙏🙏🙏
The screen protector tabs that you pull to release the film don't work, I used all of my protectors trying to get 1 to pull off, just the sticky tabs came off so I had to scrape a corner off with my fingernail to get a corner up to pull the backing off. PLUS..." Do Not Get This Adhesive On Your Skin!" I must have gotten some of the adhesive on my fingers and I scratched my forehead, half hour later it still feels like it's on fire.... I can't even imagine what would happen if it was on your finger and you rubbed your eyes. The glue can't be squeezed out of the bottle, the bottle is to thick so it sort of dribbles out even with top cap off so it's takes a minute for all the adhesive to come out, meanwhile, dust is getting on the screen.
Hi Toni, How long did you leave your Mowei screen protector on the screen for the glue to spread before placing the mini finger print iron?
its gorilla victus + and we have to go through all the steps for covering its screen. dont mind spending xtra cash samsung, just put it the screen protector like note 10+ when we buy it
They say phones are so scratch resistant nowadays but I always get a bunch of little scratches all over the screen still. Even after having the S22 ultra for a week and treating it like a baby.
Gorilla doesnt protect your screen from scratches, it just protects you from a drop so your screen doesn't go to hell. And if I'm buying a $1,700 USD phone (that's its price in Mexico), I don't mind buying a premium tempered glass protector.
I agree, I had my Note 10+ for 3 years and never took the original protector off
@@michaelscott167 yeah they used their brains then now they gone so big they got greedy
@@nathancasey7712 same thing is happening to me. I've had mine for 2 weeks and I'm starting to see little scratches everywhere
Just installed mine on my S22 Ultra after watching this video and it came out perfect!! 👍
Hi, does the front photo quality good? Because it blocks the camera
@@karthikeyans8922 it's good, I do not notice any difference.
@@viktord.8018 Thanks so much for the response.. I just tested Taking couple of pictures without the tempered glass and just placing it on top without actually applying it. I got significant difference. So thought to check with you. And, is it ok if the glue leak to the bottom portion of the phone? Because, it has a tiny gap between phone and the silver rail.
@@karthikeyans8922 just make sure you cover all the holes, so glue doesn't get in them. Especially on the bottom. On my application I noticed I may have added a bit too much and it ran on the bottom, had to scratch it off.
Worked great on my S22 ultra but I had a good size bubble near the middle of the screen,, so I gently worked it to the edge until it disappeared,, before I used the UV light to cure it. Worked great
thnks 4 this..this helped me
In my opinion I thought it was much cheaper than the whitedome but it is worth the same and in my opinion the white dome is a better option and brings more accessories that make your work easier and the footprint works perfectly that is my opinion
Wrong, DOME is a fucking mess and not as straight forward as this in any way, shape or form
@@goat8672 A MESS ? COME ON I AM NOT SPONSORED Dome, but i install that Proctectors whit my eyes close🤣🤣🤣 that easy is
My installation was going great until I bumped the guide against the glass, so now I have a small bubble on the screen. Minor inconvenience, but it still can live with it. Excellent tutorial nonetheless!
Great video, I've seen reviews for most all of these Double Glue Puddle Type Protectors to only put 1 Glue Spot for much better luck without getting air bubbles, etc. You did a great job.
My problem is, I have a dusty house & by the time I clean the screen, add the glue, I'm already getting dust on the phone.
I'm curious how these work with a case?
I've been using Self Healing TPU Screen Protectors & they only last a week or 2 before getting sticky, peeling up, dust collecting around the edges, etc..
Do it in the bathroom with shower steaming up the room, it will drag the dust down out of the air. Keep in mind this glue stuff is a bit toxic, don't want to breathe it long. Got on my clothes and left a burn on my skin for a few hours.
@@blaskotron So true. My hand is red as we speak. Attempt one failed.
What is the proper way to remove dust or lint from under the screen protector after application? In my case, the lint was black and I didn't see it while the screen was powered off.
Great video. I watched this and the manufactures video and still messed up my first one. Had air bubbles and tried to squeeze them out which made a right mess. I had to take it off, wipe the whole phone and start again with another set. 2nd time, I noticed I had more gap on the top than the bottom, left that for now. I only had 3 with my set, so got 1 left now. I have noticed the figure print sensor isn't as quick as before. But still not that bad. Fits with my original Samsung clear kickstand case.
That's because of the foam insert on top. Try to squeeze it tight into the frame AFTER you have the phone inserted
Can't say my experience is the same. I have done two installations. Both had lift in the corners one I inserted the phone into its protective case, an i-Blason Ares.
The fingerprint IS an issue with this one for 2 reasons. The glass is thicker than most glass protectors. The area on the protector intended to be on top of the sensor is off center and only half covers the sensor.
I always put 2 quarters under the weight and I haven't had any trouble with these protectors.
Bought this Set for my s21 ultra and apply it today. Im rly exzited and would buy again.
did you use two weights for the first hardening or for the second and then fit the light on top ?
@7:50 ... the only thing I don't like is the circle on the glass caused by the weight while curing.
Thats present and necessary in every screen protector
Some how I did mine and it didn't leave a ring at all 🤔. Well probably because I didn't let it sit as long as he said with that weight on it, because I didn't want that ring on it like every video i seen. Anyway, It definitely didn't register my finger prints at all 🤣. I had to redo them, but it works fine now and no ring at all, thank God 🙌🏽
I have the same screen protector. Mine doesn't have a ring like that at all. I'm not sure what he did to cause they deep of a ring as the video was edited I believe cause he talked later on about putting more weight on that area which is not needed. I think he put too much weight or so and that's why that area is like that.
I would say the less glue you have in-between the bigger it will come out and the FPS will be more effective as well. Mine works just great like as if it was stock. He did skip a few steps though cause I would recommend deleting all of your old fingerprints and rescanning them again.
What case are you using in this video?
Did that circle around the fingerprint scanner dissappear after few hours or does it stays permanently?
The circle is the sticker once removed all that's left is the slightest divit in the shape of a circle. It's not even noticeable.
Great video, but i wish someone would mention the obvious for us stupid people: MAKE SURE YOUR WORKSPACE IS LEVEL! It's hard to find a space in a house with 3 cats where fur isn't omnipresent, so I used the top of the washer for a table. It wasn't level and some of the "glue" ran off the side and, hence, there wasn't enough for a perfect installation. I'll use it for a few months and give it another go later. Glad there are 3 in the pack!
I use this as well. First protector I couldn't screw up during installation. 😄
well i did have 1 bubble on the edge, so after a few hours the fingerprint sensor did come up so i will have to put another one on.
Since there is no camera hole cut out
I would like to ask, does the screen protector affect the selfie camera quality?
I'm considering buying this and would like to know about the concerns I have with it.
Nope not at all
Hi. Many thanks for the instructive video. Although I've followed step-by-step the procedure in the video it ended up with a couple of bubbles. But, something that is bother me a lot, is it normal that after 2 days of having installed it the smell coming out of the glue is still reeking? I can feel it everywhere which is not good.
It should not be leaking. I would suggest putting the phone under the light and continuing to wipe it down. The allotted time for the light per the directions is not long enough. I would try another few minutes at minimum.
Definitely a better buy & similar application then the domeglass. I have Domeglass now but definitely picking this up
Able to follow your guide perfectly, thank you! Make sure you put the fingerprint sensor at the bottom end where the little weight goes ☺
This time was a re-application so I came back to your guide. The screen protector did its job! I dropped my phone onto a metal table foot and the screen protector shattered, intact, but my screen underneath was perfectly fine. The old one came off easily enough and there were no little pieces of glass coming off it.
What is beter mowei screen protector or Whitestone Dome glass? Looking for a good screen protector for my S23 Ultra
Hey... Just noticed that the weight included with this kit has a fine ridge around the outer edge (on both ends you can catch a fingernail on it)... I easily filed it off. Might make the ring less noticeable after the install?🤔... Hmmm.
Not sure if I even want to lock my phone at all at this point!😐
could you just tape one side of the weight?
@@BarretinJapanEasier to file the ridge off of the round weight. Tape just builds it up symmetrically. The metal is soft by the way.
I'd prefer this over the amFilm because there is no camera cutout, it makes it look so clean 😄
You don't really want another layer of glass in front of the camera because the pictures don't come out looking as good as without. It blocks the light and sometimes it shows sun flares too
Amfilm was awesome on my s20.I bought it again for the s22 ultra.
@@kokopuffs5789 I have a realme GT with tempered glass covering the front camera and had no issues with it, ofc it blocks the light when the glasss is dirty, but common, just clean it
@@teste-yh5df no issues here either so happy with it, and I have 2 spare in case this one breaks
You gotta mind the two blobs of glue don't encircle any bubbles before they reach the edge of the screen. Otherwise this is hard to mess up.
Do you have a preference for this or the AMFilm?
There is no camera hole, maybe it might affect the camera quality
That's weird
It doesn't
No
Just installed worked great. But when I scan Qr on box of product it said do not use USB c to usb c cable. Says it will not work.whats up with that. Mine did
I tried it and worked wornerfully untill 2 days later. There is a big bubble showing up at the bottom right cornee. I want to try again. Please tell me what i need to watch out to avoid this issue on my 2nd try. Thank you
Please review the ZAGG InvisibleShield screen protector
Funny how I run across this today. When mine came in the mail today 👀🤔
The Fingerprint dint work even with recalibration and Increased Sensitivity. Am i suppose to put weight while putting UV light on or before or after?
Followed your steps and worked perfectly! Thanks for the vid.
How's the camera quality?
I assume it's the same for the Note20 Ultra... (I bought the correct protector already)
Are there written / printable (PDF) instructions online anywhere?
Also, would it hurt anything to cure the glue longer (by exposing to UV lamp for longer than 45+120+30+30 seconds)?
Is there any reason I can't just use masking tape instead of the stickers to cover the ports & orifices at both ends of the phone?
ok so can you redo this install without using the weight.? I know it may possibly effect the sensor reading but I do not like that stupid circle peranently there. if one can install it without the weight does it still work?
I did that on realme GT but without UV tempered glass, and the fingerprint is perfect, so I suppose it will work just fine on s22 ultra because UV tempered glass is even thinner, lol and have more contact with the screen itself
Do tou think this is better than the whitestone dome tempered glass
I did a flawless install of the whitestone. It went on and looks perfect..But...fingerprint sensor is now very difficult to use. Probly
going to remove the whitestone as much as I hate to.
@@tikkin11 did you adjust your touch sensitivity and re-register your finger prints.i have heard of people having this issue,but all the install videos seem to look like it works.fine.
@@terryeverly5617 I took the first Whitestone off and redid the job using the spare they provide in the kit. Stole an idea here from Mowie and put a weight in the fingerprint area
while curing. This caused noticeably more glue to run out from the glass. Finished it up and now the sensor works much better. My conclusion is that
Whitestone uses just a bit too much glue, and their plastic "weight" bar is not as effective as it should be. Why some Whitestones work and other don't is most
likely related to exactly how much glue is in each tube.
@@tikkin11 is the glue easily removable from the sides?
@@chickenfordinner2093 Yes. Those provided side pads get most of it. Followed the Whitestone instructions of short cure, followed by wipe down and long cure.
If I was starting over I would go with this Mowei kit.
I used it with the s20 ultra and it was great, but is it good with the pen on the s22 ultra? Or do you recommend others?
Does the absorbent pad 100% prevent adhesive from getting in the earpiece speaker? I'm concerned it doesn't get taped over but capillary action should keep the fluid out of the hole if the absorbent pad is there, right?
I was worried about this as well and can confirm, the sponge/foam piece at the top prevents any liquid adhesive from entering there.
The foam thingys kinda work but... take the guide strips and cover the bottom holes. Cut a tiny piece off of one and cover the tiny top hole. Just to ensure that nothing gets In The speakers. Also good tip, take your s-pen out when coving the holes for a smoother seam.
First thanks for the video. I had no metal cylinder in my one for the Pixel 7 Pro. All went perfect except 2 bubbles in the center of the screen. I was afraid to take it out before putting the lights but i should have done that i think. Guess i'm obliged to remove it completely now and put another, do you agree ? Thanks
Thank you for your support, are the bubbles small? If so maybe wait until the end of the week and see if they go away. If it bothers you (like it probably would me) I would just take it off and do it again.
@@HighTechCheck it wasn't going away because the light solidifies it I guess. I tried to put another one and there was even more bubbles, driving me crazy not to be able to do anything
Thx for the video 👍 just got my S22 ultra and I'm torn between getting this mowei, Amfilm or the WS dome
I just installed mine today and I didn't leave the weight on as long as he did and I managed not to get a ring on my protector. I don't know how I did it, but I definitely had to redo my finger prints. So I probably had too much glue around the finger print area, because I had to clean it off after getting rid of the bubbles. So that's probably why I didn't have a ring.
I wondered with modern phone of 2022, Gorilla glass Victus + etc, do we even still need a screen protector to begin with ? (Case protector yes, but screen protector?)
🤔Yeah it's stupid. 😬But at least the modern screen protectors are better than they were 8 years ago😐
Does that weird circle go away with time
Just got it and installed, the finger print reader doesn't work.
Followed every step, even added 2 extra coins on fingerprint sensor. Display looks flawless, no bubbles or dust, but fingerprint sensor is bugging.... It doesnt even want to add new print 😔
I installed two of them perfect no finger print that works. Now my phone smells like that gross glue. Will that smell every go away and can that glue ruin your phone?
It goes away after like a day or three. Leave it outside for like 30 min so it can air out.
Can i reuse the same Used Screenguard after removing it?
You can clean the glue off with iso alcohol, so yes. I'll be reusing one as soon as I take the time to do it. My first install went well but for some reason, after a week, the glue just gave up and the glass started to come off... The cold conditions may be to blame but I'm not 100% sure
With S23U this is the way to go. Others, with adhesive preapplied are quite crappy, so I am back to this. I say it is only worth the prise because competition is lackluster and the end result, when you are lucky is very nice.
First one I did worked out great. No defects.
Next 3 were failures and my phone is naked for the time being.
They need to figure out better repeatability. There really is no way to get rid of bubbles once they form - you will either drain the glue from the top and sides or messing long enough in good lighting the glue dries and gets sticky, by that point it has failed.
Anyone owning a high end phone should have better things to do with their time to repeatedly waste it on applying screen protector for an hour and failing.
Bottom line: this screen protector as a whole is not a great product. It is the best only because competition is lackluster. And possibly because S23U screen is curved for no other reason than vanity and pain in the ass for screen protection.
Do they send four different glasses with different functionalities? Or all of them are the same?
They're all the same. I need different eyeglasses for this install though!🧐🤓😎🥸
They send you 3 with the kit.
I'd love to support your channel by using your links but they are all US Amazon, can you add UK going forward ?
I cannot manage getting this thing on without bubbles being left under it. so I'll probably either look for a different, non-liquid adhesive one or go completely without protector
So once you apply the liquid and lower the screen protector make sure both bubbles touch ever so slightly in the middle. Once that happens slowly lower the screen protector the rest of the way and boom you're done with no bubbles.
Do I have to use the weight? I HATE that little circle mark that it left
Ive tried without it and it didnt work at all so I'd say yes. I know how you feel about that circle, it drives me crazy. The glass needs to be as close to the screen as possible for it to work properly.
7:49 A fingerprint scanner on the back would be nice🤔
it takes 24hr to cure and fix, and removing that after one or month is pain in ass, that's the problem with uv tempred glass.
Need a good way to remove them after installing. I struggled recently to remove the dome one on my Note 10 Plus before I sent it back to Samsung.
I almost want to avoid tempered glass on the S22 Ultra now.
Floss
Hey! Would the adhesive be able to fill in any scratches?
Thanks!
Actually yes!! I can speak from experience. I have a kinda deep-ish scratch in the top center of the screen (I can catch a finger nail on it). I followed all of the instructions and you can't even tell there was ever a scratch. If you have very light scratches they'll just disappear.
what's up with the razer blade ?
what do i do with the razer blade ?
Cut up the absorbing pads (light green) if needed, but I don't think most people will need or use it.
For small cuts to self if the screen protector doesn't work out 😂
I dont use a fingerprint sensor can I leave the weight off?
You don't need the weight then.
That circle around the sensor is weird.
This one sucks. In the sun the adhesive behind the protector likes to make a blemish in certain areas. Could never not have 1 tiny tiny bubble either.
Cover switches? Package says 9H hardness denoting sapphire. It's not!
Same price as Whitestone dome. On one of the android forums, the recommendation is NO.
Does it come with the weight or is it separate?
comes with it
I had this screen protector for about 2 months. I dropped my phone from about 2.5 feet high and my screen cracked while the "protector" stayed intact. It even popped off of the screen without breaking. I followed the video exactly as shown.
hows the front camera quality with the glass and adhesive over it ?
Overall, the installation was relatively simple and the product fit perfectly. I gave it 4 stars due to the effect it has on the front camera. The screen protector rests on top of the front camera, causing images to not be as sharp. I prefer to have an opening on he protector for the camera
In Amazon reviews
I have installed this on my S22 Ultra - zero impact to the camera - still looks like it did without the protector
I put mines on today and I have got lots of bubbles .. like the glue got stuck on one side.. how do I get rid of it. I used 2 already.. does anyone know the email to contact mowei to register the warranty
does fingerprint scanner work well? what do you recommend to make fingerprint scanner work even better?
I would recommend amfilm or Whitestone, those are my favorites.
I used this product myself on the pixel 6 pro and the s22 ultra. Fantastic product! Nice review
How did it do with the S pen?
Wasted all 3 screens and had bubbles on each try...whats the tip? I watched all the videos. This is so anxiety inducing Jesus!
Level surface, Dunst free environment and make sure the two bubbles touch ever so slightly in the middle. Then just follow the process. If you need a dust free environment try a bathroom. That's what I use.
I hate the fingerprint sensor. I removed it from phone case with it built in screen protector
Great Review, so helpfull👍👍👍
been using this with my defender otterbox case and every time i drop my phone the tempered glass pops out little by little
The circle is peel off.
I almost got this screen protector but still got white stone dome instead
Have you installed your Dome protector yet? I tried twice, and even put a stack of quarters over the fingerprint scanner area while curing the adhesive, and the fingerprint scanner still does not work well.
What if you get bubbles...
If you make sure there are no bubbles in the liquid before you put the screen down you shouldn’t get any. I’ve never had bubbles with any of the liquid screen protectors I’ve ever used.
My phone screen is ruined¡! I had a horrible experience with a s20+. The curves are slightly off on the glass leaving both sides with gaps. Tried it twice with the same result. My screen now has a glare on it! HOW DO YOU GET THIS GLUE OFF!!!!!!!!!! Rubbing Alcohol don't work
Someone recommended white vinegar in the comments of another video.
How do you remove it? Its glued on lol
Just run your fingernail or a plastic pic around the edges, it will release fairly easy.
Good luck removing that thing after it shatters.... I will stick with hydrogel....
Can you recommend a hydrogel that you like?
The link actually goes to a s23 ultra screen protector
Great video, thanks for the help.
Definitely do not recommend these, always seem to bubble at the corners a day after putting on
Real nice video. Thumbs up
никогда так не делайте как на этом видео. как только вы протёрли экран от пыли, не снимайте пленку, откручивать клей и т.д. над экраном, чтоб не попала пыль, волосы с рук и т.д. снова на экран
just thank you