@benzblogsVlogs Thank all the info... We have the same alarms "ECU data fail" & ECU amber alert alarms being received continuously on our Deep C module." Previouslythe alarm clears after 2-3 attempt, but later on the alarm came followedby shutdown alarm (&gen shutsdown even when on load).. after checkingt the whetherthe wires are ok (no cuts-as u mentionedt) we investigatedthe faultto be an issue with high water temp indicaton. We located the problem & after mechanical troubleshooting we fixed the problem and generator started working "notmal as before" but the ECU amber alert continued to show. The alarm clrars only ig we remove the sender wiring on gen side. BTW, we are operating 1.5MW cummins DG which is quite old & has been left unoperated for more than 2years (but we replaced the ECU which wasn'tbrand new but seems to be in good condition). So I wanted to ask: 1) whether these alerts might be false alerts, & if not how to check & rectify the problem. 2) after fixing the initial problem mechanically, 2 days after the generatorwas on load (500KW) suddenly a loud noise was heard and we could not shutdown the alarm even from the panel or from the EmergencyShutdown button located next to the DG. ONLY after we shut off the fuel valve the engine shutoff after abt 3 mins (while the loud noise continued). So now after we started disassembling we have found that 3 head-units are broken and initial cause was due to a slipped (faulty valve). So what could be the reasons why any alarms such as low pressure alarm not be received & why wouldn't the GenSET shutdown automatically or manually in this case? Would appreciate if you could provide some information regarding problem/incident at ur earliest convenience. Thanks.
In order to solve the problem make sure this electronic engine or pure mechanical now if electronic you need EST TOOLS TO CHECK THE ENGINE WHat can cause the alrm or a problem
@benzblogsVlogs please check my commentwhich i have tagged you with just now in the comments. Appreciate & welcome all the input& help u are providing.... Regards
Good day Ben, we have DSE 6120 and Perkins Engine. Engine starts and runs, and it stops unexpectedly, sometimes it runs 3 hours, sometimes runs 1 hours with ECU Data fail. We have replaced the ECU cable with a belden cable, between controller and connection box on the alternator. There is still a +-1m cable from the ECM to a connector box on the alternator which I have not replaced. I have also not checked the ECM connection to see if it has a 120 Ohm resistor installed.
@@benzblogsVlogs Hi Ben, I only started doing the services and monthly checkups about 2 years ago. The DSE 6120 was preconfigured. The genset worked fine, until a year ago, when it started with the ECU Data fail. We have a DSE6120 with a DSE Gateway and It is Perkins Engine 2506. I am also wondering if there is an option on the DSE6120 to disable the ECU Data Fail option, so that it doesn't stop the engine when there is a data fail...
Thanks you sir sa share.sir tanong n nman I have 8610 depsea for Volvo..not start..have ECU link unknown and ECU lost no communication.i check all wiring .at nagpalit n din Ng ECU..ECU link lost p din ..balak ko palitan din Ng depsea.sensya n sir .sa laging tanong
Ok lng sir pag ganon sir check mo sir yung config mo sir baka di ng match yung config mo sa ecm type na nilagay mo da module at dapat maglagay ka ng resistor sa ecm or sa module anong module ng volvo EDC bayan or EMS
If not cranking or ither starter first do this check your battery voltage its should be 13 or 25vdc that is fully charge thin if the battery is in good condation try yo crank ang put clamp meter how much voltage droop my battery is faulty already
Hello, first of all thanks for sharing the troubleshooting. Now, I have an issue with DSE8620 that cannot start manually on DSE module or remotely from another panel, I can only start the engine with "ECU override", have you face this issue, and do you have any advice? (Note: the DSE screen is damage or sunburn)
Hi sir how about mtu with deepsee controller i am facing same isssue ecu data fail before the engine was running fine since today its start giving same alarm wiring is ok resistor is ok
Sir just check the wiring if fitted properly and check end wire connection there is posible cut in the midle try also to checkbthe volatge it should be around 1-5 volt vdc playing around or try to to check if colorcoding if same connection to ecu
Sir ok lang ba ilagay yung resistor ng ecm sa connector na ng dse para sa ecu.. mahirap kasi ilagay sa may can bus connector.. ano effect nya kung sakali.. salamat
i have duetz generater with edc3 ecm. edc3 in deutz is not available in deepsea 7320mk2 haw i can connect to the dse . volvo with edc3 is available can i choice that?
I have question ⁉️ cummins engine ecu data fail i have done wiring connections no cut all are good i changed ecu to new one i changed module also but same problem
Hi sir can you please help me I have generator that always cuts on ecu amber red but the connection is correct, it's volvo engine and deep-sea controll
Sir anong problem sa generator namin may alarm din sa ECU failure open circuit tas may naka lagay na SPN 654 FMI: 5 Sana ma sagot mo kabayan salamat po
Check mo mona ang communication wire kong walng putol or lose tapos kong may EST TOOLKIT KA doon mo pwedi ma troubleshoot doon mo malamn ang alrm ng ecu mo
Ecu amber means that there is common alarm happening in you engine wich detected by your ecm now ecu red means its already problem that cause shutdown in your engine now do one thin what engine you have if it is perkins thin use EST TOOLKIT to identify exactly what going on in your engine where you can connect to your ecm
Now if you have EST toolkit there you can see exactly there alarms in your acm that the give feedback to you module ecu amber to make you easy trouble shooting
The Existing controller ComAp it broken, now I fixed New Deep Sea 8610 after Fixed I start gen set it show Alarme as following 1- ECU Amber 2- ECU Current DTCs( Engine Diagnostic lamp low voltage, or short , SPN= 1266, FMI=4, OC=54 ) Thanks you
Mostly kong ngcrank at ayw mgtoloy at conventional engine lang sya ibig sabihin walang supply ang fuel solenoid or hinagin sya kaylangan mong mg bleed para lomabas ang hanginsir
Sir xencia na ngaun lng nakareply Ito po ung sa genset namin cummins cia KW:1000 KVA:1250 AMPS:1804 VOLTS:400 PF:0.8 HZ:60 RPM:180 ayaw cia magcrank sir
@benzblogsVlogs Thank all the info... We have the same alarms "ECU data fail" & ECU amber alert alarms being received continuously on our Deep C module." Previouslythe alarm clears after 2-3 attempt, but later on the alarm came followedby shutdown alarm (&gen shutsdown even when on load).. after checkingt the whetherthe wires are ok (no cuts-as u mentionedt) we investigatedthe faultto be an issue with high water temp indicaton. We located the problem & after mechanical troubleshooting we fixed the problem and generator started working "notmal as before" but the ECU amber alert continued to show. The alarm clrars only ig we remove the sender wiring on gen side. BTW, we are operating 1.5MW cummins DG which is quite old & has been left unoperated for more than 2years (but we replaced the ECU which wasn'tbrand new but seems to be in good condition). So I wanted to ask:
1) whether these alerts might be false alerts, & if not how to check & rectify the problem.
2) after fixing the initial problem mechanically, 2 days after the generatorwas on load (500KW) suddenly a loud noise was heard and we could not shutdown the alarm even from the panel or from the EmergencyShutdown button located next to the DG. ONLY after we shut off the fuel valve the engine shutoff after abt 3 mins (while the loud noise continued). So now after we started disassembling we have found that 3 head-units are broken and initial cause was due to a slipped (faulty valve). So what could be the reasons why any alarms such as low pressure alarm not be received & why wouldn't the GenSET shutdown automatically or manually in this case?
Would appreciate if you could provide some information regarding problem/incident at ur earliest convenience.
Thanks.
In order to solve the problem make sure this electronic engine or pure mechanical now if electronic you need EST TOOLS TO CHECK THE ENGINE WHat can cause the alrm or a problem
Godbless sir benz, sana mka upload po kau ng ecm diagram n video po, thanks at ingat lagi sir
I try sir co you know company rules but i try to make some
@benzblogsVlogs please check my commentwhich i have tagged you with just now in the comments.
Appreciate & welcome all the input& help u are providing....
Regards
Welcome back sir waiting for new video god bless you sir..
Thank you too sir take good care 🙏
Super brother very useful for me, i am working UAE we are using the same Perkins generator, thank you, 👍
Welcome
Thanks a lot my dear teacher
Welcome
nice sir keep it up..Godbless.👊
Thnks you bro.bless u
Good job sir benz...
Thanks sir
Good day Ben, we have DSE 6120 and Perkins Engine. Engine starts and runs, and it stops unexpectedly, sometimes it runs 3 hours, sometimes runs 1 hours with ECU Data fail. We have replaced the ECU cable with a belden cable, between controller and connection box on the alternator. There is still a +-1m cable from the ECM to a connector box on the alternator which I have not replaced. I have also not checked the ECM connection to see if it has a 120 Ohm resistor installed.
Ok if its shutdown what are those alarm in the module so we can easy to identify the problems
@@benzblogsVlogs the controller just says ECU Data Fail.
Ok what engine your are using did you config the module for ecm?
@@benzblogsVlogs Hi Ben, I only started doing the services and monthly checkups about 2 years ago. The DSE 6120 was preconfigured. The genset worked fine, until a year ago, when it started with the ECU Data fail. We have a DSE6120 with a DSE Gateway and It is Perkins Engine 2506. I am also wondering if there is an option on the DSE6120 to disable the ECU Data Fail option, so that it doesn't stop the engine when there is a data fail...
@@eltondupreez6875 you can but you est toolkit to open the file of the ecm and u need the extra senaor for oil and temp coz ecm not give you feedback
keep on vlogging Benz god bless
Salamat rhod bless u too and your vlogs
Sir thanks for sharing your skill..
Welcome sir
Thanks for the exposure
Welcome
Thank you so much you helped me
Welcome keep safe
thanks bro,this helps me a lot
Bless u always thanks too
Hope you're well ben if you ever come to Australia will have a job for you
Sir im not yet ben there before but thats my wish yo be there to work with💗😊
Hope to see you soon bro
Thank you
Thanks you sir sa share.sir tanong n nman I have 8610 depsea for Volvo..not start..have ECU link unknown and ECU lost no communication.i check all wiring .at nagpalit n din Ng ECU..ECU link lost p din ..balak ko palitan din Ng depsea.sensya n sir .sa laging tanong
Ok lng sir pag ganon sir check mo sir yung config mo sir baka di ng match yung config mo sa ecm type na nilagay mo da module at dapat maglagay ka ng resistor sa ecm or sa module anong module ng volvo EDC bayan or EMS
Thanks sir ganun nga nangyari ok n sir ty
Thank u sir.
8610 MK2 has two options to connect with ECM. It has CAN Bus and ECU Bus. I want to connect to Cummins CM850. Which bus should I use? \
Ecu
@@benzblogsVlogs Thanks, Bro. In which case we use CAN terminals 20, 21 & 22 for 8610 MK2.
Can you can use for synchronizing
thank you
i have a cummins engine 1.2 mw it stopping every about 3h
I have 8610 deep sea
the alarm is
ECU AMBER warning
can you help me
thank you
Ok meaning ither water in fuel or high voltage in sensor
I have problem to our Cummins Genset...not started even cranking noting what is the possible causes sir Benz..pls give me some tips.GODBLESS sir.
If not cranking or ither starter first do this check your battery voltage its should be 13 or 25vdc that is fully charge thin if the battery is in good condation try yo crank ang put clamp meter how much voltage droop my battery is faulty already
Nice vlog ..
Thanks dong
Very well
Thank you sir bless you
Hi, is that ok to swap the H and L cable? It wont do anything harm to the machine? Thank you
It will give harm coz if synch condation other generator will become load
Hello, first of all thanks for sharing the troubleshooting. Now, I have an issue with DSE8620 that cannot start manually on DSE module or remotely from another panel, I can only start the engine with "ECU override", have you face this issue, and do you have any advice? (Note: the DSE screen is damage or sunburn)
First thing i want to know if what kva ang what engine you have is synchro or si gle dg only?
@@benzblogsVlogs . It is 400 kVa, Deutz engine. Only one for black start unit.
@@jayusuzia2201 check the configuration relocated the remote connection if program correctly this is only happen if the configuration is not correct
@@benzblogsVlogs thanks for your advice. I'll check it.
Hi sir how about mtu with deepsee controller i am facing same isssue ecu data fail before the engine was running fine since today its start giving same alarm wiring is ok resistor is ok
Sir just check the wiring if fitted properly and check end wire connection there is posible cut in the midle try also to checkbthe volatge it should be around 1-5 volt vdc playing around or try to to check if colorcoding if same connection to ecu
Make sure engine is electronic and connected the wire to ecu correctly
Sir how u make change the Hertz from 60hz to 50hz
Electronic ba yan sir or conventional
Pagg convert ka sir from 60-50 kailangan magbago kadin ng program adjust sa avr adjust sa speed same sa electronics
Sir ok lang ba ilagay yung resistor ng ecm sa connector na ng dse para sa ecu.. mahirap kasi ilagay sa may can bus connector.. ano effect nya kung sakali.. salamat
Ok lang naman sir walang problima
i have duetz generater with edc3 ecm. edc3 in deutz is not available in deepsea 7320mk2 haw i can connect to the dse .
volvo with edc3 is available can i choice that?
If happen like you use conventional thin you have to install new oil sensor and engine temp in order to have monitoring in the module
I have question ⁉️ cummins engine ecu data fail i have done wiring connections no cut all are good i changed ecu to new one i changed module also but same problem
Did you do the correct cinfiguration
@@benzblogsVlogs before engine run with no issue after stop then it happens.
And what configuration
@@benzblogsVlogs are you confuse 😂
@@AhmedIrufan ecu overide that is in the module check config
Hello. can you adjust the parameter "engine run time" in DSE? Our reading is change since we replace our charge alternator. Thanks
Yes you can but in deepsea but in engine itself you can not
Just go in scada nxt maintenance you can see there
Some are not
good
❤
❤
❤
Hi sir can you please help me I have generator that always cuts on ecu amber red but the connection is correct, it's volvo engine and deep-sea controll
Thin there is problem with the engine you need eat toolkit to know what is the problem with the engine ither sensor ,calibration
Volvo tad532ge generator ECU data fail warning and RPM coolant temp not showing DEC what problem sir
Not communicating your acu and the module check the wiring
@@benzblogsVlogs last two days back replace DEC controller after coming this problem
Make sure the communication cable is not lose and have reaistor with it
@@benzblogsVlogs I check wiring is good same problem coming
Make sure that the voltage output is not higher to it should bhe0.5-1vdc if higher there wrong with your ecm
REMARKABLE😊
Thank bro
sir, 7410 plc logic pa vlog naman. hindi ko makuha ang last part na latching
Hello boss
Hi sir
Hi brother could you learn how two disesl generator synchronous each other with this controller you Had Shawn in this video
Synchronizing its not easy task unless you have experience on it or you have generator backgrounds
You have to learn first the basic befor doing this synch! Its so risky
If your electrical engr. Its easy for you to undertand
Sir anong problem sa generator namin may alarm din sa ECU failure open circuit tas may naka lagay na SPN 654 FMI: 5
Sana ma sagot mo kabayan salamat po
Check mo mona ang communication wire kong walng putol or lose tapos kong may EST TOOLKIT KA doon mo pwedi ma troubleshoot doon mo malamn ang alrm ng ecu mo
What about volvo engine but it has DSE 7320 that gives ECU DATA FAIL 🤔
Exu fail meaning mo connection between you ecm
Check the can connection my be lose
ECU amber and ECU Red
What is problem because my generator going off
Ecu amber means that there is common alarm happening in you engine wich detected by your ecm now ecu red means its already problem that cause shutdown in your engine now do one thin what engine you have if it is perkins thin use EST TOOLKIT to identify exactly what going on in your engine where you can connect to your ecm
I have problem with Deep Sea 8610 ( ECU amber Alarme)
Pl. Help me
What engine
Engine Perkins 2300 Series
Now if you have EST toolkit there you can see exactly there alarms in your acm that the give feedback to you module ecu amber to make you easy trouble shooting
The Existing controller ComAp it broken, now I fixed New Deep Sea 8610 after Fixed I start gen set it show Alarme as following
1- ECU Amber
2- ECU Current DTCs( Engine Diagnostic lamp low voltage, or short , SPN= 1266, FMI=4, OC=54 ) Thanks you
sir volvo generator 500 kva.tatagal ang andar 1 to 2 hour tapos shut down.nakalagay po sa monitor ecu data failed
Sir bago ba to or nagamit na
Ganito sir kong nagamit nato befor hanapin mo ang ECU connection mo galing module papontang ECM check ko kong hindi potol
Pag ok naman check mo yun relay at fuses ng ngbibigay ng supply kay ecm baka wala buated mga fuse
Tapos double check mo lang wiring nya baka nag loose lang yun lng po sir
mga 6 month na po sir
Hello sir I have a problem with my engine after I repair fuel injection
Coz how did you repair you open the injection pump or what do you have picture on it
@@benzblogsVlogs Because it over and under speed my team think it because of injection pump than he removed injection pump to adjust
That is the timing need to calibrate again
after he adjustment the engine run not smoothly
Follow this
ruclips.net/video/q7ZRxqcn-Ak/видео.html
Battery problem
i need this ecm wiring diagram bro please thank you
Message me in my fb
@@benzblogsVlogs done bro its ur messages
@@MalikIbrahim555 facebook.com/groups/1581429425388674/chats/5195138870614004
@@benzblogsVlogs chat is not available
@@MalikIbrahim555 there you can message
Background music is annoying
Sorry
Boss my genaretor ECU Red signal alam
Sir may problima nayan sir ither sensor or ecu na mismo ang problima nyan use EST TOOLKIT TO check the problem
Of the engine
@@benzblogsVlogs boss my genaretor ecu signal genaretor stop
Stop because ither engine has problem or ecu itself
Sir ung sa amin kc kahit crank wala ayaw nia mag crank mag crank attempt cia 123 tapos mag mag tapos mag failed to start na cia
So ganito sir if ayaw mg crank paki info kong ilang kva anong engine sya
Para malaman natin saan ang my problima
Mostly kong ngcrank at ayw mgtoloy at conventional engine lang sya ibig sabihin walang supply ang fuel solenoid or hinagin sya kaylangan mong mg bleed para lomabas ang hanginsir
Sir xencia na ngaun lng nakareply Ito po ung sa genset namin cummins cia KW:1000 KVA:1250 AMPS:1804 VOLTS:400 PF:0.8 HZ:60 RPM:180 ayaw cia magcrank sir
Checked q ung resistor nia 59.1someting lng ang nakuha q reading
My generator is ECU RED
Do this double check the wiring there is sime shorted sensor in the ecm wich connected to your ecm
Chec diagnostic test in you engine
Need your number brother
Bro message me in chat group i give you there m.me/ch/AbaxH-Wu4NQGcD2L/