Видео

Mean need to check you configuration sonething need to modify

Ikaw naman lods

That is hardware problem open the module and check the ribbon if good

Lonk is not working now new uodate from deepsea just update firmware that it

Lose means check your exciter if good or not before calibratinng avr

You must config this webnet in order to get the correct location

Go to the setting correct the setpoint that you need depend on the battery

If same problem thin update the firmware thin after that once done you must config again

What is the issues can u till me first

Sir online makabili po kayo marami

Pls clarify po yung tanong po sir para masagot natin ng maayus salamt have great day

Oh hi dear

@@benzblogsVlogs 1506 need ecm drawing can you please give

@shahzadnawaz4956 messnger

@@benzblogsVlogs please tex me messanger on not show your id

Thanks lods

Its applicable to any of the module and if u need remote you can use dse 6110 if you need amf thin 6120

Chrck your charging alternator if any voltage and check the fuses my be there is busted fuse

Sir dapat gawa kapa ng accoubt mo tapos ponta ka sa website nila

Sorry sir comapny restricted i can assist you

No you need to config or if you have flash file from other avr just direct write it

@benzblogsVlogs but the manual says that we can use this avr as analogue type by just varying voltage, stability, and by default the frequrncy is 50Hz.....you know something..??

Perkins po sir

Ha ganon ba check ko nga

@benzblogsVlogs sa bandang dulo hinto na Ang video piro dipa umabot sa dulo

What you mean calibration can u pls clarify

Due to alarm may happen lovkout meaning there alarm w/c not rectify check in the alarm list what time and what type of alarm so you can identify easly

In which in the module? Ls clarify the question so i can give you a feedback thabk you have a great day🙏

@@benzblogsVlogs On the Woodward L series governor, pin 6 of the connector

Mean remote start

Just check the digital input there you can find the rwmot start

Generator set

@@benzblogsVlogs Epic!

You can search online

This is always at digital input if u connect laptop you can see in the app

Sir ng tun ba ang generator or ng crank lang bago namatay

@benzblogsVlogs nag turn nmn po kaso ayaw lng po tumuloy parang may nag tuturn off po...

@@benzblogsVlogs idol nay nag sabi saken pa calibrate q dw po ung electronic actuator

@@enercalagauas3464 ng run or ng crank lang

Try mo dadagan ng pihit sa fuel

If display problems not all sofeyware mostly is hardware

Thank you lods

Not yet

No need for link juat update firmware that it it will work juat follw the correct procedure

Hi sir thank you so much Godbless you

@benzblogsVlogs welcome sir...thank you for always sharing good content with us always

First thing you have to check the full amp of your charger and double check the rating of your breaker if sotable

Its not good to make it in parallel because if any voltage dc differences it may cause problems

@benzblogsVlogs so my breaker rating is okay?

@@benzblogsVlogs my charger is a 6 amp charger

Salamt lods

Is this intelligent battery charger or standard battery charger

@@benzblogsVlogs it is intelligent battery charger original installed sir this is located behind DSE 6020 front panel on the upper right side originally installed in Ferbo 42 KVA standby generator(Italy) , Perkins engine no charge output to battery, although there is 13.69V output from charger battery voltage goes down daily to 11.7 V and we have to charge battery by external battery charger in the shop regularly thanks again

Ok if inteligen battery chrger and red color mean there is alrm or fault check the config from the battery chrger this ither the automatic 12-24 vdc make sure its correct setting

@@benzblogsVlogs thanks !!

If its is knstalled in the engine meaning its active

Medyo mlkas din pero saglit lng din

Welcome sir

Bless new year

@@benzblogsVlogs sir baka po pwede pahingi po idea pano po ba mag reset or mawala ang yellow alarm ng caterpillar po salamat

Ither other one will become load thin burn

Can you pls clarify sir

Welcome

I will double check if there is options of psu as what you comment thanks

@benzblogsVlogs yes first click on charger then you will see PSU mode there we can Chenge current limits. When I Change Amp then need to enable .if I disable it's automatically going to 10 Amps option . So I want to know if the PSU is enabled then how the charger will react.

@@naushadmohammad2784 Hello dear PSU mode is used for example: if there is no battery connected to the battery charger it acts as a power supply only

@@benzblogsVlogs thank you very much sir

@naushadmohammad2784 welcome

Just message me in facebook m or whatupp

Comment what i can help you

No prob

Same to you lods have a blessed new year to you