Это видео недоступно.
Сожалеем об этом.
Arduino Speed Hoverboard conversion
HTML-код
- Опубликовано: 8 авг 2019
- In this Video i show a detailed view on the Two Hoverboard tanks i build a while ago.
Part 2 / Flashing manual: • Hoverboard Reflashing ...
Here is a link to the Custom firmware for the Hoverboard mainboards original from NiklasFauth:
github.com/Nik...
and the forked one with Serial Protocol i use in the 4WD Tank:
github.com/p-h...
And here is the Arduino NANO firmware for the 4WD Drive:
gist.github.co...
If you are interested, please watch my other videos about the 4WD and 2WD Tanks.
MUSIK;
Song: Damon Empero ft. Timmy Commerford - Lost
Link: • Damon Empero ft. Timmy...
Released by Outertone. Promoted by FMW.
and • Neovaii - Your Eyes
What an awesome work 👍👏
Greetings from Egypt 🕊️🇪🇬🕊️
Eigentlich war ich lange auf der Suche nach einem geeigneten Boostedboard für mich, aber Dein Video hier lässt mich gerade komplett umdenken. Danke dafür!
Sehr gut. So soll es sein :D
You did a great job! This is the most complete and informative video on hoverboard arduino control yet! Thank you very much! Keep up! Cheers!
You just got yourself a new subscriber mate ! Nice video !
I have like 10 hoverboards laying around i need to find how you made remote control work with main board
I gave up trying to find hackable hoverboard controller and just purchased 12-60V BLDC driver boards with encoder input,. Wish me luck.
Did you get it working?
Too cool 👍
Sehr schöner Build!
Die Frenbedienung @ ruclips.net/video/MQ_EklhKByk/видео.html ist der Hit !
Schon super wie die Massenfertigung von eigentlich relativ komplexer/teurer Hardware und Niklas Engagement einem ermöglicht solche Projekte relativ leicht und erschwinglich umzusetzen.
Vor 10 Jahren hätte man locker 3x mehr Geld/Zeit investieren müssen!
Die fernbedienung ist von hier www.thingiverse.com/thing:3133640 dann aber noch für das st7789 display etwas abgeändert.
Leider ist der billig joystick nicht gut, siehe dazu mein anderes video.
Nice project :)
Thank you my friend.
Hi it such a great work I need to know what type of the joystick you use with 2 wheels drive and from where to buy
Great project. Can you please provide wiring diagram of your project ?
Thanks.
Hi, please look at the comments in this video: ruclips.net/video/NDL2_DEqnKE/видео.html there i talk about the wiring, it is very simple
Hi, my hoverboard motors just vibrate when I try and control them via arduino or potentiometer. I tried this with two differents ESCs. Would you happen to know a fix to this?
Cool
By the way is it safe to turn on the RC transmitter before turning on the hoverboard mainboards? Does the car "run away" in case you don't strictly follow the turn on sequence? In my case my platform started driving on its own and didn't react to any commands from the RC transmitter if I turned on the devices in wrong sequence :-)
thank you my friend.
I have the Arduino nano in between which also has some kind of fly away security enabled so it shouldn't drive away but as you can see in the video I was holding my hand on the tank just in case
@@atc1441 Do I get it right that the only thing you changed it the platformio config was to set the control to -D CONTROL_SERIAL_PROTOCOL and define the USART port you wanted to use?
Great work..!!
Can you please help me out I would like to build 2Wd robot as you did. Did you have any github repo for Transmitter which you build? .Thanks in advance...
ruclips.net/video/YhvPJpmJgOk/видео.html
Hello, do you do any freelance work? Would love to talk with you about a build I would like to do for my special needs son...
congratulation!! do you guys have a procedure that has at32f403rct6 chip?
Do you recommend 1 joystick over 2 for steering this way?
Do you have more info or links on the ESP32 controller?
Love the build! Now I know what to do with the two scavenged hover board motors in my garage.
Hi. Please watch part 2 of it :) there is everything you need. See the description for a link.
@@atc1441 Ah, I see. Thank you.
Nice job. Need help - I have two hub motors on the front side, but they move with different speed when they are connected to same arduino and power supply. Any suggestions on how to ensure the wheels move with same speed if they are moving just forward or backwards. Thanks. Any help would be appreciated.
ruclips.net/video/YhvPJpmJgOk/видео.html
Sir can you guide me on where to connect the pa2/tx and pa3/rx on my esp32 receiver? How about the 3.3 vcc and negative pins from main board to esp32? Thank u so much in advance.
Hi please read the other comments I already answered this :)
Hi, I’m looking to do something similar but don’t have the technical skills you do. Would you be able to help me figure out the RC side of things as it’s to power my R2d2
Hi, thank you for your interest, please watch the other part of the hoverboard, that should help you, i can not give you direct support for it sorry
Hello, I have the idea to make the same robot platform to pull loads or do the garden for example, do you think the torque is enough? Thanks
Hi. I think it should work. Its 1kw power
@@atc1441 Great thanks I will try to buy wheel motors to test!
Hi, ich arbeite gerade an einem ähnlichem Projekt und wollte fragen ob du das drei rädige Fahrzeug erklären könntest. Nähmlich wie das gebaut wurde, da ich echt dabei Hilfe bräuchte.
Moin bitte sieh dir noch meine anderen Videos über die hawerbords an eigentlich ist alles sehr gut beschrieben
Where did you get the little plates for mounting the axles? Are these parts you can buy somewhere?
Hi. They are in the original hoverboards as mounting plates :)
@@atc1441 Ah good, indeed! I was looking if its possible to move the electronics out of the way, and this will work for me as well.
As I remember arduino
espberrypi has only 1 UART, how did you connect 2 hoverboards to it?
On Arduino they can be connected in parallel.
On raspberry you could create one software UART
@@atc1441 Thanks, mate!
could you provide the codes for arduino and stm32 for differential mode ?
all i could get is codes for controlling four wheel drives using 2 stm boards.
i need to control two motors using a single stm board. please do reply
Hi you can just use one board with the code just leave one side unconnected.
so it should work like that
@@atc1441 Whether u r using 2 stm for right and left motors or for front and back motors ( I thought u r using for left and right motors each 2 motors = 1 stm (lft right))
@@inbakrish8150 ah ok.
No 1 board is for front and one for the back.
I also build the 2 wheeled version that uses the exact same code
How much do you charge to rc a hoverboard?
Hi. Do you have a video of when you made it ?
Does an Arduino work with any controller?
great job
i have few Questions
if you may please answer me
1- i have Connect the Rc Receiver Data pin to Arduino Pin 3 so what pins are the outputs for speed and Steering wires?
2- i have use this code for my arduino uno is it ready code? or i have to edit some thing because i upload it to the arduino but not working gist.github.com/atc1441/b8ece541c12da30ee4f52acabb919b02
Thanks,
I would like to know the name of the control you are using. I would like to buy one
The clarify, the esp32 remote control
Hi you can use any esp32 board, i use this one in the remote rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F142751041470
Hi @Aaron Christophel Thanks you for nice video. Im vietnamese. i want to build a 4wd as your. i watched your clip many times but cant find exactly the name of hardware you use. can you list to me the name or link of hardware need to buy. Need 2 hove boad, 2 Esp32 - wroom or Esp32 - soC ? "Arduinio now ? i cant find" , power converter 42 -> 5v for esp32 ?
Hi. Did you watched my other video about it? I explain there and in the comments
@@atc1441 I wached all your video about hoverboad. but i cant found "Arduino boad ESP32 Now which you used as ESPNowReciever "on the internet is not found.
www.ebay.com/itm/ESP32-DevKitC-Development-Board-WIFI-Bluetooth-NodeMCU-32-ESP-WROOM-32U/362959329524?hash=item54820fd8f4:g:6aYAAOSwOmBeg1HS
is this one ?
Yes that is one compatible board, any esp32 board should work
@@atc1441 Thanks you for you reply
Mich würde die Dynamik der Motoren mit der "Custom-Software" interessieren. Für maximale Dynamik müsste ein abtourendes Rad gebremst werden und im Stillstand kurzgeschlossen sein (lässt sich dann nur schwer von Hand durchdrehen). Die original Hovertboard-SW liefert höchste Dynamik und echte Drehmomentsprünge, sowie geringste (kaum messbare / wahrnehmbare) Umschaltzeiten Vor/Rück. Das geht leider aus den ansonsten gut gemachten Videos nicht hervor. Ich bleibe daher skeptisch was die "Custom-Software" angeht...
Ich habe das für mein 4WD-Projekt anders gelöst, indem ich direkt die Motorcontroller mit einer USART ansteuere, wobei die SW auf dem HB-Motorcontroller unverändert ist:
ruclips.net/video/v_-ZDsJZhyY/видео.html
Moin, die Motoren mit der Custom Software haben eine sehr gute Dynamik, du kannst von voll speed vorwärts auf voll speed rückwärts gehen. dies kann man hier relativ gut sehen: ruclips.net/video/bM1DU87ujeA/видео.html dort aber mit nur 25% leistung aktiviert. Die Firmware ist sehr umfangreich und kann auch gut editiert werden um auch z.b. das Aktive Bremsen mit einzubauen. Also ich kann es wirklich nur empfehlen anzusehen.
@@atc1441 Danke für die schnelle Info... werde ich mir ansehen!
Do you have code to control your bot with a ps2 controller?
Hi. No, but you can search for exaples for ps2 and adapt it yourself into my code
Hi, how do you control same speed for all wheels ?
It have hall sensor and control board automatically keep speed you want
@@lifeai1889 control board comes with wheels ?
@@valiokaz just get a broken hoverboard then it have a full set you just need to replace the battery and flash the firmware mentioned in video then you're good
Anybody want to hack two boards with a controller for me £200 I will supply all the parts needed and can even go through eBay to make the sale