And it's strength never lessens same as uphill welding. . No one said can be done according to them as said. I did . Yet they say still can't be done . Hmmm. Anyway cool vid thumbs 👍
good job, now the same but now a 5 mm flat 90 agrees on this heavy piece of metal! than you cant weld like this. with every material that you weld you have to look to your melting Bath. there is not one rule but you have to understand wat you are doing. the temprature/amps, the thicknes of the stick, the thicknes of the materials. and how you hold the stick.
Indeed when i first started fillet weld i was not getting both side covered and thought to myself maybe i got a junk machine but with the help of friendly facebook member , i was told running amperage and suggest that i crank it up to 80a instead of the 60a the weld rod manufacturer states.And it solved the problem wich i could share the photos but dang youtube still does not allow images to be posted in the comment section?
Köşe kaynağı yapmak için malzeme kalınlığınin normal amper değerinden biraz daha fazla artırıp acıyı da vdeodaki gibi yapıp elektrodu da biraz bastırın olacak tabi biraz alıştırma ve amperi doğru ayarlamayla olacak
Por favor cualquier persona que suelda es indispensable la limpieza, si se preocupan de limpiar bien la pieza que van a soldar se darán cuenta qué tendrá mejor aderencia queda más limpio el cordón no soldar sobre la mugre o el óxido y sí es algo ya más delicado temperatura en el electrodo en la piezas a soldar y notara la diferencia, soldar es hermoso pero hay que hacerlo como tal.
If a 7018 rod burning slang word . No chipping or little chipping needed. . First part could have been fer vid proposes then actual weld . Still cool vid
A good weld can look God but be like solder only lay on top . No penetration. Or a bad weld that has penetration but looks bad on top can hold hell on it's henges. . Or both great weld with penetration and looks good . . I've seen some bad welds on some expensive machines . Looks good but penetration is like laying solder from solder iron it just laid on top of the metal with no penetration . Ok like a glue on a block and can break off same thing. .. still cool 😎 vid . No one has ever done a 7018 rod burning down hill. . it's strength is the same as uphill. Just pay attention.
Thats because the weld will have slag inclusion. You should show everyone downhill with 7018 then do a cut and etch test on the weld. Maybe then you might figure out why welders only run 6010 and 6011 downhill because they are a fast freeze rod. Dont go welding any bridge plates or any other critical structure until you figure out what slag inclusion is and how it is caused.
@@b.p.rwebber8098 I've seen some vids that did that they shaved off a weld to show opening were the weld didn't weld right . And one can down weld on 7018 . I don't have the money to do what y'all do on video lol. Merry Christmas to y'all.
![Veeze - F.A.F (ft. Rylo Rodriguez) [Official Music Video]](http://i.ytimg.com/vi/7hlz2S2GmIY/mqdefault.jpg)
You turned up the amperage for the second pass. The first was a very cold weld hence no fusion between the metals.
Arc burn, no proper angle,long gap in between base metal and electrode, no fusion.. This happen in first pass.😂
Thanks bro love from India
Try down hill weld on 7018 . No one seems to do it according to some . Same thing slag falls off . And stuff
Good job bro. . Saluttttttttttt from WELDER 🇮🇩❤️🔥
Привет 🙋
Очень красивая ролик спасибо
And it's strength never lessens same as uphill welding. . No one said can be done according to them as said. I did . Yet they say still can't be done . Hmmm. Anyway cool vid thumbs 👍
good job, now the same but now a 5 mm flat 90 agrees on this heavy piece of metal! than you cant weld like this. with every material that you weld you have to look to your melting Bath.
there is not one rule but you have to understand wat you are doing. the temprature/amps, the thicknes of the stick, the thicknes of the materials. and how you hold the stick.
Ur not a welder.. (. .)
is very good
Do that on .065 exhaust pipe
Indeed when i first started fillet weld i was not getting both side covered and thought to myself maybe i got a junk machine but with the help of friendly facebook member , i was told running amperage and suggest that i crank it up to 80a instead of the 60a the weld rod manufacturer states.And it solved the problem wich i could share the photos but dang youtube still does not allow images to be posted in the comment section?
Good job
Köşe kaynağı yapmak için malzeme kalınlığınin normal amper değerinden biraz daha fazla artırıp acıyı da vdeodaki gibi yapıp elektrodu da biraz bastırın olacak tabi biraz alıştırma ve amperi doğru ayarlamayla olacak
god!! this is interesting xx
Mentah lasanny yg pertama yg kdua keren Mateng sempurna
In vertical position how amper hawe in 2 milimetres profil
Por favor cualquier persona que suelda es indispensable la limpieza, si se preocupan de limpiar bien la pieza que van a soldar se darán cuenta qué tendrá mejor aderencia queda más limpio el cordón no soldar sobre la mugre o el óxido y sí es algo ya más delicado temperatura en el electrodo en la piezas a soldar y notara la diferencia, soldar es hermoso pero hay que hacerlo como tal.
Me ensina a solda metalon redondo na chapa 20?
It's a thick plate, it's nice to try using a plate of 0.8 can you look like that the result
Thanks
Good trick
Rất tuyệt vời
Hasilnya sangat bagus
El 6013 es el más fácil de soldar . Casi sin saber quedan cordones lindos. Con un 7018 en posición 3f deberías hacer prueba
How many amperage the second?
Если бы ты не был тупым, то знал что на 3 миллиметра нужно 85-105A
Good bro
If a 7018 rod burning slang word . No chipping or little chipping needed. . First part could have been fer vid proposes then actual weld . Still cool vid
Kolay gelsin 👏
Uno que es chispero sabe que con cualquier soldadura quedan cordones bien asta con la 60-10
👍👍👍👍
Assalomu alaykum............... 👍🇺🇿
Arc burn, no proper angle,long gap in between base metal and electrode, no fusion.. This happen in first pass.😂
אין כמו אימא בעולם!!!!!!!!
אין כמו אימא בעולם!!!!!!!
Saya akan coba mengelas seperti itu
I also have a similar channel which is about welding
Đường hàn quá đẹp you 👍👍👍👍
Ничего удивительного нет! сначала видео напругу убавил на следующим этапом видео поднял напругу
Not to mention the electrode was not held in tight like the second weld. Like you said no secret just proper welding.
A good weld can look God but be like solder only lay on top . No penetration. Or a bad weld that has penetration but looks bad on top can hold hell on it's henges. . Or both great weld with penetration and looks good . . I've seen some bad welds on some expensive machines . Looks good but penetration is like laying solder from solder iron it just laid on top of the metal with no penetration . Ok like a glue on a block and can break off same thing. .. still cool 😎 vid . No one has ever done a 7018 rod burning down hill. . it's strength is the same as uphill. Just pay attention.
Thats because the weld will have slag inclusion. You should show everyone downhill with 7018 then do a cut and etch test on the weld. Maybe then you might figure out why welders only run 6010 and 6011 downhill because they are a fast freeze rod. Dont go welding any bridge plates or any other critical structure until you figure out what slag inclusion is and how it is caused.
Quá đẹp
капец толстый металл, надо фаску снимать и в 2 подхода
The secret is practice and learning from your practices. Which you need alot of practice
Amp ? 120 ?
Hàn cơ bản cho người mới
Nice. 🇧🇩🇪🇬
אין כמו אימא בעולם!!!!!!!
@@user-ui4cq5yb4d boro i am not zionist.
@@Akhand-Bangladesh אין כמו אימא בעולם!!!!!!!
Tan sólo con arrastre 🤔
Pokaż na 2mm blaszce taki spaw
😮😮😮💪💪💪🙂🙂🙂
Только и умеете на Толстых листах сварить
i
Не зачёт! какой бы шов не был бы красивый подрезы на заготовке не должны присутствовать а у тебя они есть так что то что ты сварил сродни браку
Why even post this like really
Olmadı yaptiğın kaynak
Pasını pisliğini temizlemedin her videoanda aynı sen kendine iyilik yap bu işi bırak
I was told it couldn't be done by other welding people at their school or some otj . . Prove me right. I've done it so I know it works.
Then make a video and do a cut and etch and show the result.
@@b.p.rwebber8098 I've seen some vids that did that they shaved off a weld to show opening were the weld didn't weld right . And one can down weld on 7018 . I don't have the money to do what y'all do on video lol. Merry Christmas to y'all.
@@b.p.rwebber8098 merry Christmas to y'all
@@b.p.rwebber8098 thickness of metal or the thinnest Wich one . Y'all rich and can I'm not so . I've actually done down welding on 7018
@@b.p.rwebber8098 yes some slag will be on . Hence sine if not virtual no chipping hammer 🔨 needed on 7018 .
Толстый металл варить просто. А тонкий хер за варишь