That is a beautiful looking case build,one ive seen that was similar had a lovely copper fluid added which i think would have complimented the over all colour scheme of the build,well done tho 8)
6.2. Degrees at most if thickening the rad like Yung bul was planning to do. Bros nice. 65 cpu and hotspot at 54 with 34 ambient not bad at all. For a 4090 & R93d. 4090 is soooo much cooler then the 3080 for example. At least at the junctions anyways. Others in the comments need to dead the hate. 😂 loosen up an shit. 💀
Here i am still roaming around cyberpunk 2077 on my ultimate MSI 970 GTX video card, i4690K Processor. Its still playable but when i drive to fast roads and buildings dissappear if you go even further than that u fly through the sky's and see the full layout of the map.
Can you please link the tool that has grooves in it for guiding the tube bends? Looked like 90 and 45degree channels. Don’t see it in the video description
great shots and awesome montage. i watched over a thousand pc build videos and i can confidently say this was one of the best. good job. also, great build overall. i would pay more attention to all tubes being parallel, tubes between cpu and distro plate wasnt quite the same level. other than that no mistakes, 9.5/10
It’s a very clean build! I notice you use plenty of EK water cooling components. I know you built this last year prior to the Gamer’s Nexus investigation, but want to know if you would still use them today?
love this build. looks beautiful but also I always wonder about just how much radiator support is needed. This shows me that I can easily settle for a 360mm + 240mm in a case like this as you got great results with just single 360mm.
i really like the way you present step by step. makes it much easier to consider planing a build in this case. my itx build is currently in a streacom DA6 and im considering to just swap things around. its a 5800x + 3090 on dual 240 radatiors. with left over be quiet light wings. and i have a 360 radiator left over wich could fit on top. so i can mount 2x 240 radiators and a 360 on top if im correct? and since i got a itx board in this case that would also be no problem. since the vertical gpu hides it anyway. and i could mount my pump res combo right next to the gpu. so far i really like this case.
Thank you so much for your detailed and kind response, we are glad that you like our step-by-step format. As for your system, our main concern is the 2X 240 on the side. Is it going to be too tight with a push-pull config and a pump res combo? If you do it, let us know how ti goes!
We offer build consultation services to guide you through the entire process of picking your custom loop water cooling products if you’re interested ☺️
We do both! We assemble PCs for clients as well as offer one-on-one virtual consultations and guided builds. Head over to our website archetypeorigins.com and fill out a build inquiry so we can get in touch with you!
not gonna lie, how hard is it to get a new case by you guys? coming from a matx off brand lian case, lowkey need a new nxzt h7 flow white, but also like how the hyte y60 is but need a nice case :) got a bad airflow and temps sometimes are crazy but need a new case. this has been my first pc, and lowkey needs a upgrade 😂, everything was on a budget had to sell a lot for this
Nice build, do you think any other 280 rads would fit? I’ve been planning a build around the huge y60 and that’s kinda interesting to hear about the rad not fitting. Also what was that block called you put around the CPU
Yes! we are currently working on another custom water-cooled Y60 and we are able to put a different EK Rad inside. Stay tuned for the video! The block around the CPU is an anti-bend frame. It keeps the CPU from warping. We have it linked with our affiliate links!
![Insane Open-Air Custom Loop Water PC Build [RTX 4090 | Ryzen 9 7950X3D]](http://i.ytimg.com/vi/gqji3kbb_vA/mqdefault.jpg)
![Insane Open-Air Custom Loop Water PC Build [RTX 4090 | Ryzen 9 7950X3D]](/img/tr.png)
![HYTE Y70 Monochrome V3 ⚫ [Custom Loop Water Cooling PC Build] Intel i9-14900K | RTX 4080 Super](/img/1.gif)
Can i have a free pc? PLS pin me at least? Im subbed
no PC, but here is your pin 😘
@@archetype_origins ty☺
wake up child,, go to work
@@efggalih2280ur pfp😭😭
Build turned out amazing! Thank you for all the continued support 💛
When she/he mounted the gpu sideways it was too much too handle 😂😂😂🔥🔥🔥 this is just madness man 8k build
Thanks my friend ✌🏻🔥🔥
Awesome build! I can't wait to see who it is!
New video is out now!
Beautiful setup. WOW
🤩🤩🤩
Sick build! I can't wait for my Y70 to arrive and start my build.
We are also highly anticipating some HYTE Y70 Builds!
Love the orange Cumputer.
Bruh 💀
@@Archetype_Ben hahaha
love your channel/videos and the editing is always on point!
Thank you so much!!🥳
That is a beautiful looking case build,one ive seen that was similar had a lovely copper fluid added which i think would have complimented the over all colour scheme of the build,well done tho 8)
Thanks for the support! For the build you’re working on are you considering doing custom loop water cooling or are you going to be air cooling?
@@archetype_origins Im going to mount the AIO i have to the side by the mobo,i dont have the tools or the skill set to custom mount it regrettably 8).
Very Nice build! and Video! Love it!
Thank you ☺️
Beautiful build!
Glad you like it!❤️
Tempratures are not bad at all, i dont think that second rad could make so much difference! BTW nice build!
maybe another 2 degrees but a lot of additional money.
6.2. Degrees at most if thickening the rad like Yung bul was planning to do. Bros nice. 65 cpu and hotspot at 54 with 34 ambient not bad at all. For a 4090 & R93d. 4090 is soooo much cooler then the 3080 for example. At least at the junctions anyways.
Others in the comments need to dead the hate. 😂 loosen up an shit. 💀
Here i am still roaming around cyberpunk 2077 on my ultimate MSI 970 GTX video card, i4690K Processor. Its still playable but when i drive to fast roads and buildings dissappear if you go even further than that u fly through the sky's and see the full layout of the map.
One day you will get there! Don’t give up!
Why don’t you ever disclose the cost of the build??? Maybe other people may want one ya know??? 😂
If you want to know the cost of the build send us an inquiry and we can get back to you! archetypeorigins.com/inquiries
Any idea for the next Custom Loop Water-Cooling project?
White antec torque build with sky white sx primochill vue with silver fittings and clear pipes. That would be so freaking awesome.
H6 FLow - dont think anyone has done it yet@@Double_iice
@@bushwookieplays8629h6 flow custom loop water cooling? 🤔
@@Archetype_Ben yeah, think it would look insaine, plus want to see sombody do it before I do 😂
What is the screen inside the PC that you used to display temperatures?
Can you please link the tool that has grooves in it for guiding the tube bends? Looked like 90 and 45degree channels. Don’t see it in the video description
Might have missed that one, here you go:
amzn.to/3uH64W0
great shots and awesome montage. i watched over a thousand pc build videos and i can confidently say this was one of the best. good job. also, great build overall. i would pay more attention to all tubes being parallel, tubes between cpu and distro plate wasnt quite the same level. other than that no mistakes, 9.5/10
Glad you enjoyed!
It’s a very clean build! I notice you use plenty of EK water cooling components. I know you built this last year prior to the Gamer’s Nexus investigation, but want to know if you would still use them today?
@Archetype Origins - nice video. What did you use for mounting the GPU?
The Y60 comes with a vertical mount included
@@archetype_origins Nice. My Phanteks NV7 doesn't >:[
@@skynetintex5878 That's unfortunate, but you can always get a vertical mount for that!
Китаец - а ты хорош !!!
Thank you! ☺️
Hello from Malaysia 👋
Hello boss 🫡
🇲🇾
Спасибо за видео и за вашу работу
Thanks for watching and your comment ❤️
In-home setup for this PC is out now!
ruclips.net/video/tPPUwdcahPU/видео.html
What’s the screen inside
love this build. looks beautiful but also I always wonder about just how much radiator support is needed. This shows me that I can easily settle for a 360mm + 240mm in a case like this as you got great results with just single 360mm.
Yes sir sounds like you have a good plan 🫡
@@archetype_origins what is your rpm settings for the 3 radiator fans ?
We set it to PWM, we didn’t do any custom curve
i really like the way you present step by step. makes it much easier to consider planing a build in this case. my itx build is currently in a streacom DA6 and im considering to just swap things around. its a 5800x + 3090 on dual 240 radatiors. with left over be quiet light wings. and i have a 360 radiator left over wich could fit on top. so i can mount 2x 240 radiators and a 360 on top if im correct? and since i got a itx board in this case that would also be no problem. since the vertical gpu hides it anyway. and i could mount my pump res combo right next to the gpu. so far i really like this case.
Thank you so much for your detailed and kind response, we are glad that you like our step-by-step format. As for your system, our main concern is the 2X 240 on the side. Is it going to be too tight with a push-pull config and a pump res combo? If you do it, let us know how ti goes!
How much does it cost when compare to the regular build with the same spec ?
You could probably get away with $6k
Great build! Can I ask what the trap song playing on the showcase was? Sub was going hammer
how many fittings did you use on the build ? like how many of each?
We offer build consultation services to guide you through the entire process of picking your custom loop water cooling products if you’re interested ☺️
awesome build
is there y70 distro out yet i would like to get one
No Y70 disto as far I know
Great design. Is there also an education service available in a company or just assembling it for a client?
We do both! We assemble PCs for clients as well as offer one-on-one virtual consultations and guided builds. Head over to our website archetypeorigins.com and fill out a build inquiry so we can get in touch with you!
@@archetype_origins Prices for online or in-center courses
Online only!
@@archetype_origins
Great, we will contact you as soon as possible
not gonna lie, how hard is it to get a new case by you guys? coming from a matx off brand lian case, lowkey need a new nxzt h7 flow white, but also like how the hyte y60 is but need a nice case :)
got a bad airflow and temps sometimes are crazy but need a new case. this has been my first pc, and lowkey needs a upgrade 😂, everything was on a budget had to sell a lot for this
What kind of case are you looking for? Process of getting a case from us will be smooth like butter 🧈
hey, love the build
For displaying your favorite live wallpaper or monitoring your components temperature!
Nice build, do you think any other 280 rads would fit? I’ve been planning a build around the huge y60 and that’s kinda interesting to hear about the rad not fitting.
Also what was that block called you put around the CPU
Yes! we are currently working on another custom water-cooled Y60 and we are able to put a different EK Rad inside. Stay tuned for the video!
The block around the CPU is an anti-bend frame. It keeps the CPU from warping. We have it linked with our affiliate links!
280 alphacool will fit, fittings on top or bottom , black or white.
@@archetype_origins Great, thanks for the reply!
What is that screen/monitor you put inside? At the top back
links in description
what torque settings did you use for the cpu contact frame?
I usually just set the torque to the lowest setting possible.
His teeth are triggering me but still a perfect Video, keep up the content. ❤
🥲 thank you 😬🤓
Where does the small 3 pin coming from the gpu water block plug into
ARGB header on your mobo
Are there any nice Block for the GIGABYTE GeForce RTX 4070 Super WINDFORCE
The more rads is just a myth...
More radiators means more thermal capacity. However, it does not guarantee lower component temperatures
what screen is that you have inside and how did you attach it?
We found the BEST beginner 5'' LCD Screen Display MOD for your PC! [Unboxing and Installation]
ruclips.net/video/jIz-nnLEcVo/видео.html
excellent milk cooled PC
🐮😋
Do you have a link for the anti static mat?
The EK mat?
@@archetype_origins oh is it ek? Okay im sure i can find it then
Is there a link for the LCD screen display on that PC?
amzn.to/42H6DMC
Goo+
Please explain 😂
one 360 slim would be enough with an undervolt otherwise air would have done the same for way cheaper
How did you sync the orange on the lcd and on the rgb?
I am using wallpaper engine on the LCD screen, and manually change the light hue to orange to sync with the RGB fans
İntro sound : Matrix BLUE STEEL
Huge fan of Blue Steel's music!
must be nice having small hands no way myXXL hands fitting in them spaces
🤣😂🤣
The total cost for this beautiful "bild" is $6000?
Closer to $7k
How much did this puck cost in total?
For build inquiry, kindly fill out this form:
archetypeorigins.com/inquiries
good!!!!!!!!!!!
Thank you!!!!!!!!!!!!
can this exact build be done in y70 touch?
Absolutely, some modifications are needed but definitely possible!
cool im thinking going with msi meg godlike motherboard @@archetype_origins
That's a beast motherboard for sure 🔥
All Amd, Intel or arm and Nvidia
we SHOULD do more AMD 🤜🏻🤛🏻
Could have been a good build, bought the wrong RAM(CL36 non neo version). I'm choking
How is that wrong? 😅
How much to build this machine in USD ??? Hi from Brazil
Around $8k
so expensive for the water cooling parts.
Yea, they can get pretty expensive sometimes 🥹
what length did you cut the tubes too?
All tubes are measured and cut on the spot, we did not keep records of the length of the tubes
Play ARK then it will go crazy in temps
gpu temps are obviously fake. heaven for two hours and only 570Mhz and 45w gpu power at 12:30.
The benchmark was turn off when I was talking but you can see that the power average around 300w and 2400 MHz
lol until you start gaming I'd like to see what those gpu temps are sitting at 🤣
Roger 🫡
GPU was only taking 40watts tho
At the moment of recording yes, but you can see that it averages about 300w
shity case
What lenght screws did you use at 5:34 ?
I believe they were 3mm
God this was cringy. Skipped to end.
Did you like the end? 😃
Horrible hard tube bends, the 90 degree ones!! Great vid BTW....
Thanks 👍