Please share the basic circuit . Also specify for what type of BLDC motors this circuit is applicable . If the wattage of the BLDC motor is around 300 watts wil this circuit still be applicable or else what changes would be needed in this circuit for higher wattage BLDC motors Very good job done by a fellow Indian
The gerber file you linked is different to the one in the video. it does not have a +VCC port. Could you please link the same pcb board that you used in the video? I need it for a physics assessment at school.
I have a 4 wire motor from a hard disk drive but there is no indication which wire should be the ground. I have tested them for continuity but it seems that both end wires are common to the other 3 wires. Is this correct? And if so does it not matter which end wire is connected to common/ground.
Greetings Teatcher. Thank you for the excellent project. 1) I built the circuit on a Protoboard, initially to experiment, and I am using 5V 2A as the Power Supply. It is working but usually I have to give the Motor a push. So I don't know if a Power Supply with more Voltage or more Amperage is needed. Any hints? 2) Does this circuit work also for CD Rom Motor? Thanks a lot.
Quick question.... does this controller allow the motor to run forward/clockwise and then straight into reverse/counter-clockwise or just one direction?
Good circuit. This type of circuits are very much needful for star configuration of BLDC motors but are useless for Delta configuration BLDC motors. My request is if possible, do not rewind the BLDC motor from delta to star, rather try to make a ESC which is compatible for running all delta configuration motors.
You are right. I have just got my board from the printers and there, is no pin on the board to connect to ground. But from the CD pins 2 and 3 of the Pot are connected to ground and appear to be like this on the board so I am going to try connecting the ground wire to pin 3 of the pot.
if your motor has no Common pin you can connect 3 wires together then a 1k resistor to get the neutral point on resistor free pin and use it as Common wire. for more info see BLDC motor winding structure.. I prefer to use HDD board motor driver instead it is more specialised for the motor itself.... Good luck
@@CreativeTechosincorrect, the fets are rated to 60v, but the gate is only rated to 20v, to 20v max, and the fets are ~50A if kept cool (fan or heatsink)
şef kolay gelsin bir proje var yardımcı olabilirisin , x bir tane teker var buna sensör bağlı hızını ve tur sayısını belirliyoruz, buradan teker 1 tur atarken sensordan aldığımız bilgilere göre dc yada step motorumuzun tur sayısı yarım olacak yanı teker bir tur atarken motor yarım tur atacak bu konuda yardımcı olabilirimsin
![Seungmin "그렇게, 천천히, 우리(As we are)" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/kAzmhLHePqU/mqdefault.jpg)
Can you tell me how to make a controller for 48v (1000 w motor) /20amp
Please share the basic circuit . Also specify for what type of BLDC motors this circuit is applicable . If the wattage of the BLDC motor is around 300 watts wil this circuit still be applicable or else what changes would be needed in this circuit for higher wattage BLDC motors
Very good job done by a fellow Indian
The gerber file you linked is different to the one in the video. it does not have a +VCC port. Could you please link the same pcb board that you used in the video? I need it for a physics assessment at school.
Very good explained..
Can you share another circuit but with Hall.
How much voltage required input line on pcb min to max?
12-90v max but if you want lower voltage input you can use other type of low power mosfet irfz44n or high power 24v mosfet irf3205 its 200w 80A max
good job. for the A2212/10T motor has only 3 wires, how to connect Vcc? Thanks
I have a 4 wire motor from a hard disk drive but there is no indication which wire should be the ground. I have tested them for continuity but it seems that both end wires are common to the other 3 wires. Is this correct? And if so does it not matter which end wire is connected to common/ground.
muchas gracias por la información tan completa.
Thanks for watching my friend 🙂
Do they deliver to Brazil?
can the same be done with 3 IRFBC40 MOSFETS WITH 4 DIODES and 2 zeners and capacitors for 6 wires input to ZWS 400 NON CARBON BRUSH MOTORS , ??
Great work.
I love it.
What about a very HV (12 - 120vdc) & High Amp (80A - 120A) circuit.
Can you please help?
Got components that can handle 14 kW? 120A @ 120Vdc is over 14 kilowatts, 80A @ 120Vdc is about 10 kW.. good luck with that.
@@WOJTACH27 thanks so much.
Super! Thank you very much! Good idea!
Thanks for watching my friend 🙂
Can I test gimbal motor with this circuit?
how does it work properly? there is no start up sequemce?
Greetings Teatcher. Thank you for the excellent project.
1) I built the circuit on a Protoboard, initially to experiment, and I am using 5V 2A as the Power Supply. It is working but usually I have to give the Motor a push. So I don't know if a Power Supply with more Voltage or more Amperage is needed. Any hints?
2) Does this circuit work also for CD Rom Motor? Thanks a lot.
1. try more voltage
2. if it is a 4 terminal motor = yes
Thanks @@user-rs8zg8ey2b
Quick question.... does this controller allow the motor to run forward/clockwise and then straight into reverse/counter-clockwise or just one direction?
It works only clockwise
@@CreativeTechosincorrect, switch 2 motor wires and it will run the other way, so you could add a DPDT toggle switch to add reverse operation.
@@CreativeTechosHow he recognise to run clockwise?
Just one direction
Good circuit.
This type of circuits are very much needful for star configuration of BLDC motors but are useless for Delta configuration BLDC motors.
My request is if possible, do not rewind the BLDC motor from delta to star, rather try to make a ESC which is compatible for running all delta configuration motors.
Thanks for watching my friend, i will try to upload video ASAP for delta version too 🙂
Sir one prize charity
Hello, and what are the BLDC motors with Delta configuration? Tks
Correction, star with center tapped connection, not the majority of star wound motors
In your given zip file there is no place for negative input, where I should join the negative input of battery ?
Negative input goes to the common wire of bldc motor
And Where I should connect positive input
You are right. I have just got my board from the printers and there, is no pin on the board to connect to ground. But from the CD pins 2 and 3 of the Pot are connected to ground and appear to be like this on the board so I am going to try connecting the ground wire to pin 3 of the pot.
Thanks 🌹🌹🌹🌹🌹🙏🙏🙏🌹🌹🌹🌹🌹🌹🌹🌹🌹🌹🌹🌹🌹🌹🌹
Thanks for watching my friend 🙂
if your motor has no Common pin you can connect 3 wires together then a 1k resistor to get the neutral point on resistor free pin and use it as Common wire. for more info see BLDC motor winding structure.. I prefer to use HDD board motor driver instead it is more specialised for the motor itself.... Good luck
How to make a controller for Delta winding motor.
Yes I'll soon upload video for delta version
@@CreativeTechos 3pin bldc motor
Great work sir
hi i neēd 3 phase DC controlier 100a +- 300v, can you make it ?
Brillient sir thkyou
My pleasure, Thanks for watching my friend 🙂
hi my bldc motor have 3 wire where i give power supply wire in controller pl tell me
bait click thumbnail. it wont work with 3 lead motor
can the het sink hole and metal connection be used to feed power? I suspect.
Bom muito bom , aonde eu compro essa placa
Thanks for watching my friend 🙂, you can use Gerber files to order board, or use pref board and follow schematics.
What is the supply voltage , what is the maximum output .
The supply voltage is 5-12v 30A max
@@CreativeTechosincorrect, the fets are rated to 60v, but the gate is only rated to 20v, to 20v max, and the fets are ~50A if kept cool (fan or heatsink)
My motor has only 3 wires. No 4 wires like vídeo. Then how to do. Please help
Dây thứ 4 là điểm chung của 3 dây u v w
Citkit drive link please ❤
Can we use this circuit with bldc fan motor?
Yes, You can use this, Max current output is 30A
bait click thumbnail. it wont work with 3 lead motor
@@user-rs8zg8ey2byes , fake board oh shit, it dont work on BLDC 3 wire
Where does the positive voltage on the circuit if the motor does not have a common wire?
nowhere, this circuit cannot drive 3 wire motors, like his thumbnail shows, its bait and click, unless you want to rewind the motor, lol
Great!!! Thank you very much
Can i connect delta motor?
no, not even a star motor with only 3 wires
Как заказать такие платы?
What is the overall cost for this project
Near about 100 INR
Где можно взять такую плату?
Bro make a signal booster aah using basic electronics
Yes, I'll try to upload ASAP
How can I make big one for 1500w motorcycle
Create a video explaining how to get the common brushless motors
nice
Thanks for watching my friend 🙂
Sir i want controler tester divaice digram plz new tester bldc. India name dist.....
The files for download, Link is in video description
@@CreativeTechos sir tester divaice digram 8pin ic nober bldc trohtal .hall sensor tester masin box new
f the motor does not have a connection to the hub, this circuit is useless
Sir kese parched kafe
How to use drone motor?
the bail click thumbnail is what got me to watch, it wont work unless you rewind the motor = fail
👏👏
Thanks for watching my friend 🙂
şef kolay gelsin bir proje var yardımcı olabilirisin , x bir tane teker var buna sensör bağlı hızını ve tur sayısını belirliyoruz, buradan teker 1 tur atarken sensordan aldığımız bilgilere göre dc yada step motorumuzun tur sayısı yarım olacak yanı teker bir tur atarken motor yarım tur atacak bu konuda yardımcı olabilirimsin
Bldc 3 wires simple esc
Thanks for watching my friend 🙂
bait click thumbnail. it wont work with 3 lead motor
Nie , are you China Citizen?
Nope I'm from India
indians are the ones who spread pointless vlogs. just to earn money.
he is the indian guy on RUclips
without pcb board
👍👍👍
Picture shows a 3 wire motor and the video uses a 4 wire motor very confusing make up your mind
Bunun parça numarası varmış parça artikel numarası varsa 5 adet isterim
0:31 0:31
You didn't make bldc esc.. you are modifying bldc for your 3 led chaser circuit 😝
Where does the positive voltage on the circuit if the motor does not have a common wire?
bait click thumbnail. it wont work with 3 lead motor