I measured the 2 rear nuts, the adjusting nut to the lock nut with a tape measure to make sure they measured the same before tightening up the 17 and 14 bolts. Anyone else do it that way?
What chain would you recommend on these things? I have tried a few different chains an after a few rides they are stretched so far I can no longer adjust any more slack out them.
@@kevingalindo1 Exactly what I was saying (lose slack = tightens), so wouldn't you set the 1" slack with weight on the Quad? Anyways, that's what I just did. Like the put in gear tip, thanks.
HI I did this and those 2 screw u turn in to tighten the chain there like all the way in and chain still loose am I doing something wrong I loosen the top and bottom bolts ?
Tom Green Go to partzilla.com for a new one. May as well buy both while your at it. They have exploded views where you can see it all. I’ll post a link below. Number 23/24 www.partzilla.com/catalog/yamaha/atv/2002/banshee-yfz350p/rear-wheel Sure you can find used ones on Ebay.
I measured the 2 rear nuts, the adjusting nut to the lock nut with a tape measure to make sure they measured the same before tightening up the 17 and 14 bolts. Anyone else do it that way?
Thanks for the video was very helpful! Will be tightening my chain tomorrow morning.
You're like the fastest mechanic ever
You are a Master! Greetings and thanks from Mexico.
Luis De Santiago
Thanks man!
What chain would you recommend on these things? I have tried a few different chains an after a few rides they are stretched so far I can no longer adjust any more slack out them.
kevin when you tighten up your chain how do you keep the rear end in line so you dont run side ways if you no what i am saying
Eric Phillips Mine is like that the chain is right but my left tire is way in
Mine is like that then when i sit on it it has no play is that fine?
Shouldn't you put weight on the seat as it will lose slack when you sit on the seat. Great video btw.
MPDano tightens when you add weight 😉
@@kevingalindo1 Exactly what I was saying (lose slack = tightens), so wouldn't you set the 1" slack with weight on the Quad? Anyways, that's what I just did. Like the put in gear tip, thanks.
MPDano oh I read wrong lol, that’s what the 1” of up and down slack compensates for. You never want it set “tight” too hard on bearings.
@@kevingalindo1 Thank you sir
HI I did this and those 2 screw u turn in to tighten the chain there like all the way in and chain still loose am I doing something wrong I loosen the top and bottom bolts ?
Did you find a fix my banshee has the same thing going on rn
Great video!!!
hi have u got any videos on tie rods and arms set up what is the stock lenth iv got a tie rod at 131/2 inch or 345 mm
Does the chain go on top of the top roller ? Or below the top roller
It goes below the top roller and above the bottom roller.
What number is that bottom 17 bolt on partzilla I need the bolt the 14 nut and washer
Great video
where can i buy a replacement bolt for the swingarm to tighten the chain? i stripped mine😫
Tom Green
Go to partzilla.com for a new one. May as well buy both while your at it. They have exploded views where you can see it all. I’ll post a link below. Number 23/24
www.partzilla.com/catalog/yamaha/atv/2002/banshee-yfz350p/rear-wheel
Sure you can find used ones on Ebay.
South Texas Banshee thank you soo much! i really appreciate it keep up the great work!!
Mine got stripped to. How did you remove it?
what about alingment??
Is this the same for a Yamaha warrior 350?
My hardware was 10mm 12mm and 14mm
what type of chain is that?? whats the best brand of chain and sprocket to go with??
Pierre Smith
DID Is a great chain, also Primary Drive is Great you can grab them on eBay and Rockymountainatvmc.com
yea i hear did is the best imma got wit them
is there a difference between a motorcycle chain and a tv chain?
Amin Wade
Nope, some chain offer a higher tensile strength, but a 520 chain is a 520 chain
ok thanks!
what type of oil would you recommend for a pro mod trans push a 421cc Cub and how much oil?
what is good chain to use with a banshee d.i.d or oem
christian diaz
D.I.D. and primary drive are very good chains.
What are sprockets for a stock banshee?
14/41
Thanks man videos are great
such a poor design. I'd recommend people just buy a round house style swingarm. so much easier.
Thomas Dodson
Agreed