Honestly, I did not understood a thing you said. However, dang you solved my problem! I stil do not know how - I touched a couple of times the metal trigger next to the lamp just like you did, reinstalled the lamp cover and voala - I have a working projector agian. Big thanks!
Hi I have Benq MS 524, it runs for 10min, then suddenly lamp fails color wheel and fans are running for 2min after error Lamp indicator, I have changed lamp and ballast still problem remains pls suggest fault.
Your videos are amazing... I am facing a small problem with my benq mw612 power supply board.. The transformer of the projector is broken... Please could you suggest me a replacement of the same or if you have any extra transformer of the same model then i am ready to pay you in exchange of the transformer... Thank you.
hi, I have an mp620p projector, when I turn on the leds they are all ok, the lamp turns on and after a few seconds it turns off. the LEDs always remain ok without any alarm, the projector remains on, commands blocked and the lamp is off. can you help me, i'm going crazy .... thanks
I got BenQ MP525 ST , it works fine upright but when I put it on a ceiling bracket(upside down) it starts flickering like the colour wheel is going nuts. Any idea what is causing this?
Hi there. I have watched many of your videos looking for solution to a problem with my benq W1070. I havent found anything like it. But you seem to have a lot of experience with this type of projectors. My fan nr.4 (its the one next to the speaker) stopped working. I have replaced it but no luck. The new one wont move. I looked through and i found out that the connector on the motherboard got a little burned. The pins on the back of it has melted. I have a little soldering setup at home but this connections are microscopic. I wont even try fixing it on the motherboard. My idea is to connect the fan somewhere else where its easy to get 12v that runs once I power up the projector. I could easily hook it up to the cable of the front biggest fan and run the two on that one connection. Would that work ok? Wouldnt this put too much current on that part of the board? Maybe you have a better suggestion... Thanks
@ raotech laptop and projector lab I have a very similar BenQ ms521p projector and my one won't spin up the inner fan unlike your does at 15:39. Can you help me out what part controls that? I can't figure it out. Replaced the fan but not that was the error. New fan still does nothing. I used multimeter and checked the legs, there is about +-0.3V runs in there. That should be a problem. But can't solve it. Thank you!
@@nfmhits8157 Not yet, can't find anybody who understands how it works. I was thinking to buy a new motherboard on ali, but there is an electronics mb, and a power mb, and i cant find out which one controls it. Buying both of them for 80$/pc is not the best option...1 must be enough...
Hello sir my project power light showing only red light it need to be green when i press power button and then only projector start but now only showing red light and it is unable to run. What might be possible problems on showing red power light red.
HELLO GREETING FROM VENEZUELA. I HAVE A BENQ MS513 PROTECTOR VERY LIKE THE ONE IN THE VIDEO. AND IT LIGHTS WELL. BUT AFTER 5 MINUTES AFTER OFF. AND I DISCONNECT IT AND THEN IT TURNS ON AND SOMETIMES LASTS 45 MIN AND THEN IT TURNS OFF AGAIN, I DO NOT KNOW IF IT IS THE LAMP OR THE FAN
HOLA SALUDO DESDE VENEZUELA. YO TENGO UN PROTECTOR BENQ MS513 MUY PARECIDO AL DEL VIDEO. Y ENCIENDE BIEN. PERO AL CABO DE 5 MINUTOS DE APAGA. Y LO DESCONECTO Y LUEGO ENCIENDE Y AVECES DURA 45 MIN Y LUEGO SE VUELVE A APAGAR, NO SE SI ES LA LAMPARA O EL VENTILADOR
Hi. My projector after coming ON, it switches off in 20 seconds and the lamp error light comes on RED. I saw your video on youtube. It that the solution to this problem.
Honestly, I did not understood a thing you said. However, dang you solved my problem! I stil do not know how - I touched a couple of times the metal trigger next to the lamp just like you did, reinstalled the lamp cover and voala - I have a working projector agian. Big thanks!
Hi I have Benq MS 524, it runs for 10min, then suddenly lamp fails color wheel and fans are running for 2min after error Lamp indicator, I have changed lamp and ballast still problem remains pls suggest fault.
Your videos are amazing... I am facing a small problem with my benq mw612 power supply board.. The transformer of the projector is broken... Please could you suggest me a replacement of the same or if you have any extra transformer of the same model then i am ready to pay you in exchange of the transformer...
Thank you.
hi, I have an mp620p projector, when I turn on the leds they are all ok, the lamp turns on and after a few seconds it turns off. the LEDs always remain ok without any alarm, the projector remains on, commands blocked and the lamp is off. can you help me, i'm going crazy .... thanks
Good job
I got BenQ MP525 ST , it works fine upright but when I put it on a ceiling bracket(upside down) it starts flickering like the colour wheel is going nuts. Any idea what is causing this?
Hi there. I have watched many of your videos looking for solution to a problem with my benq W1070. I havent found anything like it. But you seem to have a lot of experience with this type of projectors. My fan nr.4 (its the one next to the speaker) stopped working. I have replaced it but no luck. The new one wont move. I looked through and i found out that the connector on the motherboard got a little burned. The pins on the back of it has melted. I have a little soldering setup at home but this connections are microscopic. I wont even try fixing it on the motherboard. My idea is to connect the fan somewhere else where its easy to get 12v that runs once I power up the projector. I could easily hook it up to the cable of the front biggest fan and run the two on that one connection. Would that work ok? Wouldnt this put too much current on that part of the board? Maybe you have a better suggestion... Thanks
I have ms502 can you tell me the number of the ic 611 in the power supply
@
raotech laptop and projector lab I have a very similar BenQ ms521p projector and my one won't spin up the inner fan unlike your does at 15:39. Can you help me out what part controls that? I can't figure it out. Replaced the fan but not that was the error. New fan still does nothing. I used multimeter and checked the legs, there is about +-0.3V runs in there. That should be a problem. But can't solve it. Thank you!
Did you figure it out
@@nfmhits8157 Not yet, can't find anybody who understands how it works. I was thinking to buy a new motherboard on ali, but there is an electronics mb, and a power mb, and i cant find out which one controls it. Buying both of them for 80$/pc is not the best option...1 must be enough...
I have a benq mp610 the power, temp, and lamp indicator lights are flashing orange rapidly all at once, what is the caused of this issues.
Hello sir my project power light showing only red light it need to be green when i press power button and then only projector start but now only showing red light and it is unable to run. What might be possible problems on showing red power light red.
Thank you
ayudaaaa, tengo un video beam siragon modelo pys 2100s no he conseguido la lampara de que otr maner puedo arreglarlo soy de colombia
HELLO GREETING FROM VENEZUELA. I HAVE A BENQ MS513 PROTECTOR VERY LIKE THE ONE IN THE VIDEO. AND IT LIGHTS WELL. BUT AFTER 5 MINUTES AFTER OFF. AND I DISCONNECT IT AND THEN IT TURNS ON AND SOMETIMES LASTS 45 MIN AND THEN IT TURNS OFF AGAIN, I DO NOT KNOW IF IT IS THE LAMP OR THE FAN
My problem Hitachi XGA CP-X327 when i on power suiz after sec lcd screen on, then fius burning...fius 5a 250v...i don't know why...any one do know it?
Sir dell 1210s ka diagram kha se download kare
OK karen to pahla cala kea dikona si plk kis tara di audi ha uncal ji
Sir projector repair ki training kaha se le bata do pls
sir kisi question ka answer ni detay......
HOLA SALUDO DESDE VENEZUELA. YO TENGO UN PROTECTOR BENQ MS513 MUY PARECIDO AL DEL VIDEO. Y ENCIENDE BIEN. PERO AL CABO DE 5 MINUTOS DE APAGA. Y LO DESCONECTO Y LUEGO ENCIENDE Y AVECES DURA 45 MIN Y LUEGO SE VUELVE A APAGAR, NO SE SI ES LA LAMPARA O EL VENTILADOR
Hermano el mío presentó lo mismo debes hacer mantenimiento a los ventiladores
Benq mx806pst lamp suddenly off after sometime but butten light colour (green) not change
Please tell me solution sir
¿ Quiere limpieza solamente?
Hi. My projector after coming ON, it switches off in 20 seconds and the lamp error light comes on RED. I saw your video on youtube. It that the solution to this problem.
i have the same problem, but i dont know what this guy is doing
Benq I have ice top258pn hot
how much voltage is epson lcd projector emp-s4 lamp ?
Can I give direct 230 voltage on projector Lamp
Please reply Sir
Kr kya rha h service k alava a
Starting is gud but Finishing is not Perfect work
Always at ur video , only you clean the projector , no technical service , try to upload technical service
gunga hai kiya?
Gunga aur behra dono hai