Clara, first I want to say thank you for these videos. These are a great reference. Second, would it be possible to get a PDF copy of the charts you made showing? Printed papers are much easy for me to read than trying to reference a video timestamp.
Hi Clara. We have a GWeike 1500w fiber laser and having troubles with piercing 5mm aluminium. When piercing there is slag being deposited on top of the work piece which then the nozzle is touching. What parameters do you recommend for 5mm Alu (cutting and drill parameters)
Hi your videos are execellent! I’m getting fine dross on 6mm stainless steel on these parameters, any suggested changes to get and fine adjustments to get a nice cleaner cut?
Hi Clara, thank you for videos they're very helpful, please tell me if we can use just air compressor to cut carbon steel with 3000w Laser source, thank you in advance.
I tried these parameters on 1.5 kw raycus machine. All parameters are almost the same except the gas pressure. My machine cuts well at 1 bar pressure o2. I am still figuring out why is it so?
Hi Clara We have a 4 kw fiber laser machine my biggest problem is 12mm carbon steel it take very long to cut 4hrs long I want to get at least to 30-40 min on this . What size laser shoed I get and in what KW to get this
Hello Clara, I hope you are doing well, I am trying to cut 0.5 mm PVD coated stainless steel (With film on)on 3000W MAX Source but whenever I do so my nozzle gets heated, Can you please help ?
Can you help me find a suitable parameter for cutting a 20 mm carbon steel sheet according to the part that is a gear wheel, so that the gear part is clean
@@ClaraChai thanks for reply ma'am. How did you say there is a problem with the nozzle because I was check laser center and piercing side was ok ..but in same days uper lence was damge ..
None of parameters in this video is working. I tried them on my 4000w laser machine and every single one needed more power and focus and gas adjustment
Hello @Clara. Thanks a lot! Your library is quite effective. It was almost perfect for my 2kW Bodor T230. Do you have the same library for a 12kW multidiode laser source? Again, thank you!
@@ClaraChai Thanks for your answer. Ok, I understand. In any case, I've eard that there is no need for 12kW power to cut Carbon Steel with Oxygene. So, I'll use your 8kW parameters in that case. Since my laser source is a multidiode, and your parameters are for single diode laser, do you have any advices to adjust your parameters (8kW, O2 gaz) to my laser? Greetings from france!
Thank you very much for sharing this information Clara.
So welcome!
Hi, can you please also share your pierrcing parameters for 3k watss, thanks a lot
Great video Clara, thanks for sharing
☺️
Clara, first I want to say thank you for these videos. These are a great reference. Second, would it be possible to get a PDF copy of the charts you made showing? Printed papers are much easy for me to read than trying to reference a video timestamp.
Thank you, but sorry, Paul
I figured as much. But thank you for the response and again, thank you for these videos
@@paulb8264 you are welcome
If you have an iPhone, you can capture the screens then transcribe the text into your own excel sheet.
Sorry, no
Love Clara's ❤️. Help
Thank you
thank you very much fir all that you do
Thank you
Thank you Clara so much .
So welcome!
Thank you for your help
Hello Clara. THank you for video. Do you have cutting parameters for Raycus RFL C6600 Single module? In this video only for 6000 Multi Module
I don't have your parameters, please check this video for referece ones.
Thank You Clara.
You are welcome, please share my channel with more people, thank you
Yes sure
Bagaimana cara mensetting mesin ketika setelah di reset ?
Very nice video
Thank you
Hello Clara, I am looking for cutting parameters for laser max photonic 6000w and boci head collimator head 100 and focus 200. You have?
Sorry.
Hi Clara. We have a GWeike 1500w fiber laser and having troubles with piercing 5mm aluminium. When piercing there is slag being deposited on top of the work piece which then the nozzle is touching. What parameters do you recommend for 5mm Alu (cutting and drill parameters)
I don't have your parameters, if you are looking for data, check the video for reference ones.
Hello, parameters for carbon steel used aire compressed ?
Hi Clara is there any possibility you can do a video on the rotary with EZCad and the settings please 🥺
Sorry, not recently
can you add 12000 w settings to this
Let me try to figure it out some day
Hi your videos are execellent! I’m getting fine dross on 6mm stainless steel on these parameters, any suggested changes to get and fine adjustments to get a nice cleaner cut?
Also this on 1500kw raycus using cypcut software
It is just for reference, you need to find yours.
What are the parameters for piercing in 3mm? for a 1000w. BTW your videos are great!
Thank you, glad you like it.
Thank you for sharing. just one thing, would it make much difference if i use these parameters with different collimation and focus of my machine?
Yes
Hi clara i have a question please
This parameters for autofocus what we will change if we have laser head manual fucos like bt240s
Thanks
?
Hi Clara, thank you for videos they're very helpful, please tell me if we can use just air compressor to cut carbon steel with 3000w Laser source, thank you in advance.
for thin metal, less than 3mm
thank you so much
Welcome!
Make Next vedio on Laser head.
Colametric lens, focus lense, protective window.
Please share link of above parameter. Im not able to find parameter for Raycus 6600w single module.
Also share piercing parameter.
Sorry, no
Hai Clara, thank you for this video, are these parameters same if we use air compressor?
no, only for reference.
Clara, thanks for this references, but can you share parameters for cut tube square in tube pro?
Sorry, no
Hola, los tutoriales de cypnest estan en castellano? Si me uno a tu canal?
No Spanish, cause it is not supported in CypNest.
Why My BM115 Focus200 Can be set Focuu Only -10/+10. so can't cut 25mm Streel
Please check your focus lens.
can i use this parameter with Focus200
@@trapetch I think so
Tq mam
my laser machine is 1000W and new but the cutting nozzle cuts like a jigsaw shape instead of straight so how to adjust cuts straight line?
Can you cut straight line now?
Thanks for your videos they're great. I have been looking for parameters for engraving lines. Is that something you could make a video on?
later a short
@Clara Chai Ok, thanks. I'm looking forward to it.
Hi Ms clara, do you have parameters for 1.5 Kw for compressed air? in the video it just N2 and O2
Sorry, I don’t have them.
Any suggestion why carbon steel 4mm is welded together at button? Laser cut through but too much burr which welded part togeher. Thank you
Maybe power to much.
I tried these parameters on 1.5 kw raycus machine. All parameters are almost the same except the gas pressure. My machine cuts well at 1 bar pressure o2. I am still figuring out why is it so?
They are just for reference, I am glad most of them are helping. If the gas pressure is not fit, please just take yours. Thank you.
Hi Clara We have a 4 kw fiber laser machine my biggest problem is 12mm carbon steel it take very long to cut 4hrs long I want to get at least to 30-40 min on this . What size laser shoed I get and in what KW to get this
Higher power will be fast than 4kw, but you also need to consider about other factors, like the cost.
Choose 4 mm double nozzle and pressure 1 bar then speed 22 and focus +5
What is the use of 2 screws behind the collimating lens?
for laser centering purpose
Hi Clara. What is parameter for carbon steel 3mm with 1500W with nitrogen gas.
Why nitrogen?
Hello Clara, would you share for 12000w laser ?
Thank you
You can check my membership videos.
Mam if you have teligram channel send link
Is there an imperial chart for laser parameters?
Sorry, no
Hello Clara,
I hope you are doing well,
I am trying to cut 0.5 mm PVD coated stainless steel (With film on)on 3000W MAX Source but whenever I do so my nozzle gets heated, Can you please help ?
Is the laser beam at the very center? You need to check. There is a nozzle video on my Channel, you can fine the center setting in it.
Check red beam and lens .
@@ClaraChai red beam is centre correctly
@@namangarg661 Probably you need to check the gas setting. It can not be fixed by a simple answer.
hello clara
Can you help me find a suitable parameter for cutting a 20 mm carbon steel sheet according to the part that is a gear wheel, so that the gear part is clean
FINDING PARAMETERS IS A LONG JOURNEY, please ask help from your supplier.
Hello miss Clara can i ask you about parameter of each sizes of carbon steel metal thanks
You can find it in the video.
Why is my lower lens damge in lower side in 2 days what's problem plz guide and also thanks for this video
Check your nozzle
@@ClaraChai thanks for reply ma'am. How did you say there is a problem with the nozzle because I was check laser center and piercing side was ok ..but in same days uper lence was damge ..
I was work 3kw...
@@sharmakuldip2403 So that is why we need more information, you did not mentioned the upper lens at all.
Make sure your beam centring is not ok
what are the cutting parameters for galvanized sheets?
In the video.
Hi please can you make a video with 12 kw parameters?
Sorry, it is not in plan.
Hi…Ms. Clara, Can you send me the cutting parameters like the above video of the 6000W laser cutter as a PDF file?
Sorry, please find it n the video.
@@ClaraChai thank you
what is the parameter for aluminum 3mm with 1kw and nozzile size, gas ???
Er, please try to find it in the video
Pls make a video on 12kw to 30kw laser parameters 😊😊
Noted.
Please make video on trumpf 10kw laser machine parameters
Noted, thank you
None of parameters in this video is working. I tried them on my 4000w laser machine and every single one needed more power and focus and gas adjustment
Haha, thank you. So I took one month to gather the data here, for what? It is not 1+1, try all 500-8000, and then tell me.
I think she made it clear that these settings my change from machine to machine.
Share parameters with compressed air
Hello @Clara.
Thanks a lot! Your library is quite effective.
It was almost perfect for my 2kW Bodor T230.
Do you have the same library for a 12kW multidiode laser source?
Again, thank you!
Sorry, no those parameters.
@@ClaraChai
Thanks for your answer.
Ok, I understand.
In any case, I've eard that there is no need for 12kW power to cut Carbon Steel with Oxygene.
So, I'll use your 8kW parameters in that case.
Since my laser source is a multidiode, and your parameters are for single diode laser, do you have any advices to adjust your parameters (8kW, O2 gaz) to my laser?
Greetings from france!
Hi! Ms. Clara, Can I have 12KW power fiber laser cutting parameters?
I don’t have 12kw parameters, sorry
hi. how to 1500w. cutting parameters air pressure from Screw Air Compressor
You can find a suggestive air pressure in the video.
Do you have a link to download in PDF?
Nope.
Hello and courtesy
It is possible to send the cutting parameters for 0.3 mm copper material for 1.5 kW fiber laser.
thank you
6mm ss parameter with oxygen 1500w
If you can not find in the list, sorry no
Please send 1.5mm aluminium air parameter please 3kw
All reference parameters you could find is in this video.
5:50
Hole countersink parameters
I am not sure of the question.
1:05
Can u send this pdf
Sorry,, no pdf.
1.5kw laser 2mm cs with air parametr plees
You can find it in the video.
alt yazı neden yok
Altyazıyı açmamış olma ihtimalin var mı?
Are you in teligram
+86-13335151833
Hi, can you please also share your pierrcing parameters for 3k watss, thanks a lot
Please wait a while, I am still struggling making the HypCut those days!