another great fix...good to show everyone the importance of having the correct tools but also showing people what to do if they don't have the specific tools....thanks Don
And this, ladies and gentlemen, is how a repair video should be made! Very clear video and audio, well-demonstrated technique, and a description of each tool used along with alternatives. Thanks Dony! I am on your channel a lot, and I am always impressed!
Good video. I like how Don shows an alternative way to make this fix without special tools. Wasn't complicated and very straight forward. Thanks again.
I enjoy working on older quality equipment like Stihl, especially their saws. The Stihl 026 came out in the late 80's and early 90's. So getting 33 years out of a 2-stroke is amazing, especially a chainsaw.
Dear Dony. The way you present information is actually comforting to me. You leave nothing for guessing.😮 I don't have to be a pro to understand you. The lights you use to show us what you're doing is excellent. I wish you were my brother but I can pretend.❤ Thanks😊
Great video, Dony. Another reason to use a pick or the special tool is so you don't damage the surface of the spring, which can weaken it and cause it to break over time.
I always enjoy watching your videos even though I have been doing this stuff for years now. I find my self saying out loud what you are going to do next. I guess it's a good review if anything. For homeowners, your channel is so helpful. Most people just ignore things like this, even though it is annoying and unsafe. My feeling is it avoids getting dirt in the chain when you sit it down and it is still turning like that. Thankyou for the awesome videos friend.
Thank you for a very informative video and repair. I could watch your videos all day long. Because of you, I maintain and clean my MS170 after each use and enjoy showing others how to use and maintain theirs. Also, I would like to say Thank you for acknowledging that us women also watch, learn and repair our chainsaws with your knowledge and guidance and great videos!
...great DIY video Don...I was given an 026 last year that was not running....I have restored it and it runs great...I will be looking for the "stretched spring" issue, and now, thanks to you, I know how to fix it.....keep 'em coming...I luv your posts!... 🙂
Thanks Don, I took a guess and thought it was the clutch, and even though I know how to do what you did. I have not done it such a long time and it was a great refresher. Cheers
Hi Donnie! Take a llook at the frames where you show the OE springs in place and compare to the new springs in place later on. The replacement springs have about 1/2 or so fewer coils and the gaps between coils are larger than what you observed for the originals; ie the new springs are of a stronger rating even though the old ones were fatigued, they were never as "strong"as the new if the metalurgy is the same -- "I guess". Thanks!
Very good Don! I have it on good authority that one of the first things he reached for as an infant, was a wrench and a ratchet! And his first motor tear down and rebuild was before the age of five! 😯 🤩 😆 You never fail to impress me Don. Stay safe and cheers from the States.
MS201t and MS200 are notorious for this problem at my work. The springs will either break or wear into the clutch shoes causing them to expand into the drum which will spin the chain. More often than not, I will change the entire clutch and not do the springs.
This repair is such a rewarding one if the old springs are really shot. It only cost a few dollars and is not instantly appreciated when u go to use your saw. Some may say oh...I can just set the brake to stop the chain moving but if the springs are bad, the engine will stall.
I have a Stihl 017. Starts right up and runs good. But if I turn it off it’s very difficult to restart when it’s hot, I’m not choking it on warm starts. Where would you look for the problem?
Hi Dony - I have a vintage Stihl 031 on which the brake lever has 3 positions: lock, neutral & run. I have never seen another chainsaw with the "neutral" position, where I can rev the engine, the chain remains in an unlocked state and the clutch stays disengaged. Have you any experience with this setup?
I am sorry, I see that this version of 026 runs the pump all the time that the engine is running. I think that it must be the 026 PRO that has the pump worm driven by the clutch drum. Love your information and your willing to share it.
So so so many other videos of others It just kills me that they never clean items off just put a replacement part in, and reassemble. When I take the time to pull something apart I always clean it up, just makes it easier to do a good job. And the intention of the videos that don't clean their items they have the intention of flipping such item. And yes buyer beware!
Never a good idea to use abrasive teeth pliers on springs. You'd be surprised at how little scoring it takes to make a spring break & fail later on. Also failed to mention to measure the thickness of the shoes and the drum surface thickness the shows press against. There are factory wear specs for both of these. In this example, they look OK, but always better to measure.
I disagree with you, the lower the idle is set, the more bottom end torque and quicker rev response you will have. Saw engine also will stay cooler with a 2300/2600 rpm idle.
I hope that after you used your underwear to clean the clutch drum, you don't put them back in the wash and continue using them for their intended purpose. 😂🤣😂🤣
another great fix...good to show everyone the importance of having the correct tools but also showing people what to do if they don't have the specific tools....thanks Don
And this, ladies and gentlemen, is how a repair video should be made! Very clear video and audio, well-demonstrated technique, and a description of each tool used along with alternatives. Thanks Dony! I am on your channel a lot, and I am always impressed!
Indeed, Brian!
Good video. I like how Don shows an alternative way to make this fix without special tools. Wasn't complicated and very straight forward. Thanks again.
I enjoy working on older quality equipment like Stihl, especially their saws. The Stihl 026 came out in the late 80's and early 90's. So getting 33 years out of a 2-stroke is amazing, especially a chainsaw.
Dear Dony. The way you present information is actually comforting to me. You leave nothing for guessing.😮 I don't have to be a pro to understand you. The lights you use to show us what you're doing is excellent. I wish you were my brother but I can pretend.❤ Thanks😊
The 026 was my dad’s first Stihl … and he gave it to me 5 yrs ago as my first Stihl!
Great vid! It’s in need of some maintenance and this helps a ton!
Great video, Dony. Another reason to use a pick or the special tool is so you don't damage the surface of the spring, which can weaken it and cause it to break over time.
Man the amount of useful information on your channel is amazing. Thank you for posting this information.
Great video. That 026 is a legend. One of the best small saws Stihl ever made.
You diagnosed my 028 issue. Thanks
By far the best tutorial I’ve ever seen about anything ! Sockets sizes, part numbers, alternative techniques, great filming… way to go buddy!
I figured it had to do with the clutch. Great to know how to look for stretched springs. Another great one, Don. Thanks
I always enjoy watching your videos even though I have been doing this stuff for years now. I find my self saying out loud what you are going to do next. I guess it's a good review if anything. For homeowners, your channel is so helpful. Most people just ignore things like this, even though it is annoying and unsafe. My feeling is it avoids getting dirt in the chain when you sit it down and it is still turning like that. Thankyou for the awesome videos friend.
Yep, most people put up with things on equipment that haven't been working right for a multitude of reasons.
I’m from Croatia and this helped me today fixing my 044 and cut my firewood, thank you very much!
Nice job I made a homemade hook like that and it works very well. Nice job enjoy watching your videos.👍
Perfect timing. I just bought an 041 at an estate sale. Now I now how to fix the only issue it had.
Thanks for the alternative methods to remove the springs.
i wouldn't have imagined they'd sell the springs separately . great fix , thanks db .
You can use steel wire and loop the spring leg then vice grip pull the the wire just like that tools.
Thank you for a very informative video and repair. I could watch your videos all day long. Because of you, I maintain and clean my MS170 after each use and enjoy showing others how to use and maintain theirs. Also, I would like to say Thank you for acknowledging that us women also watch, learn and repair our chainsaws with your knowledge and guidance and great videos!
Great video. The chain was still creeping a bit. Did you turn down the idle?
It's getting to that season here in the North East, snow blowers and chain saws. Thanks for all you do!!!
That's a good lesson to learn, i use to think it was something to do with the Idle screw setting, but i was wrong. Cheers from newzealand.
Great video! I had this exact problem with the chain spinning, by coincidence on an 026. Replaced the springs and it works perfect. T/hanks you Dony!
Had the issue with an MS180 - it was a dirty clutch drum like you mentioned at the end.
Thank You Thank You...
...great DIY video Don...I was given an 026 last year that was not running....I have restored it and it runs great...I will be looking
for the "stretched spring" issue, and now, thanks to you, I know how to fix it.....keep 'em coming...I luv your posts!... 🙂
Thanks Don, I took a guess and thought it was the clutch, and even though I know how to do what you did. I have not done it such a long time and it was a great refresher. Cheers
My favourite Friday morning show thx D Boy. Will try this on my 034
Hi Donnie! Take a llook at the frames where you show the OE springs in place and compare to the new springs in place later on. The replacement springs have about 1/2 or so fewer coils and the gaps between coils are larger than what you observed for the originals; ie the new springs are of a stronger rating even though the old ones were fatigued, they were never as "strong"as the new if the metalurgy is the same -- "I guess". Thanks!
Alway's looking fwd. to Fri. and learning something from this channel
They are pretty hard to get on if I remember right . Great video . Might be doing that some we have a couple of old well used saw .💪🏼
BRILLIANT
MATE!
Never knew you could do this. I would probably have ordered a new clutch. Great tip. Thanks!
I knew there had to be another way to stop that chain from rolling. Thank you Donyboy 73!!
Thanks don I’ve learned something new every time I watch your videos 👍🏽👍🏽
Excellent video Don , very helpful indeed 👍
Excellent tutorial with superb editing!
Great vid Dony,as always. Always learn something from your videos, 👍👍. Reminds me of the clutch replacement I just did to my Echo GT-225 trimmer.
Great video as always Donny 👍 those were excellent little saws
Great video. Never would have thought of that. Thank you.
Thanks Don...super good advice that applies to all brands.
snap on and mac also have a set of seal hooks witch would work as well but yours would work equally well not to argue...
I have a gunsmithing spring tool that works well for clutch springs. Brownell's and other suppliers have them if you cannot find the Stihl tool.
Very good Don!
I have it on good authority that one of the first things he reached for as an infant, was a wrench and a ratchet! And his first motor tear down and rebuild was before the age of five! 😯 🤩 😆
You never fail to impress me Don. Stay safe and cheers from the States.
Thanks for sharing.
You have taught us a lot.
Great job done!😎👍
Tq for share
Thanks a million. Great video.
Nice one. Thank you!
Great info as usual, thanks Donny.
MS201t and MS200 are notorious for this problem at my work. The springs will either break or wear into the clutch shoes causing them to expand into the drum which will spin the chain. More often than not, I will change the entire clutch and not do the springs.
TY for Sharing
Thanks Dony
This repair is such a rewarding one if the old springs are really shot. It only cost a few dollars and is not instantly appreciated when u go to use your saw. Some may say oh...I can just set the brake to stop the chain moving but if the springs are bad, the engine will stall.
OUTSTANDING BROTHER! THANK YOUY!
Awesome is always Donnie thanks for showing us
Thanks donyboy73, taught this ol timer something new 👌 👍 much appreciated 👏 🦅🦅🦅😊
Been there, done that!
Awesome video thank you
Would it be easier to do one spring at a time? It looks like it help by keeping some tension on the clutch.
Very informative. Thank you brother 👍
Excellent video once again, Dony.
Thanks, Don. I purchased the tool.
Thanks!!! Great content!!!😊❤
Super well made video and great information Don! ☀
Greetings from Sweden
Nice video, figured they would make you buy a new clutch, and old drawers as a rag,lol
Always Very Informative Videos!!
Not only do my parrots wake me up with happiness, Dony does too! As always you have GREAT tutorials!!!
Nice one,well done
Was the shoes newer? Didn’t see wear marks from the springs. Great info. Will check into that tool.
Can probably make spring tool from old bicycle spoke
Great video
Peace of a wood cloth pen works great too keep shoes in place
Nice videography. Very nice.
Diamond job again donyboy 🤩👍
Good video!
I think replacing the whole clutch would be smarter. I think I would check the rpm also
I have a Stihl 017. Starts right up and runs good.
But if I turn it off it’s very difficult to restart when it’s hot, I’m not choking it on warm starts. Where would you look for the problem?
Hi Dony - I have a vintage Stihl 031 on which the brake lever has 3 positions: lock, neutral & run. I have never seen another chainsaw with the "neutral" position, where I can rev the engine, the chain remains in an unlocked state and the clutch stays disengaged.
Have you any experience with this setup?
Why not use chain break when installing springs? Will it damage?
The chain brake tightens on the outside of the clutch drum. It is removed.
I am subscribed you share some great information.
👍
👍👍👍
I thought that the 026 oil pump has a drive arm that fits into a notch on the outer edge of the clutch drum?
I am sorry, I see that this version of 026 runs the pump all the time that the engine is running.
I think that it must be the 026 PRO that has the pump worm driven by the clutch drum.
Love your information and your willing to share it.
So so so many other videos of others It just kills me that they never clean items off just put a replacement part in, and reassemble. When I take the time to pull something apart I always clean it up, just makes it easier to do a good job. And the intention of the videos that don't clean their items they have the intention of flipping such item. And yes buyer beware!
I'm sorry....but @ 8:48 ..... is that a set of men's boxers ya got there ??? 🤣🤣
Keep up the good work Dony....been watchin' ya for over a decade !!
It must be a broken clutch spring
? I didn't see you use Chain Brake some don't have Chain Brake
Never a good idea to use abrasive teeth pliers on springs. You'd be surprised at how little scoring it takes to make a spring break & fail later on. Also failed to mention to measure the thickness of the shoes and the drum surface thickness the shows press against. There are factory wear specs for both of these. In this example, they look OK, but always better to measure.
ty
Best saw I ever had, some a$$hat stopped by one day and stole the saw and the copper gutters from my house.
I disagree with you, the lower the idle is set, the more bottom end torque and quicker rev response you will have. Saw engine also will stay cooler with a 2300/2600 rpm idle.
I hope that after you used your underwear to clean the clutch drum, you don't put them back in the wash and continue using them for their intended purpose. 😂🤣😂🤣
I was going to ask for the Stihl part number for the official cleaning rag….
Some times you got to recycle what you got!
Brake cleaner is nasty. Please wear gloves
Shoulder use underwear, particularly if it's your wife's underwear, as a rag
I figured it had to do with the clutch. Great to know how to look for stretched springs. Another great one, Don. Thanks