Hi friend to configure the ESC with the board can we leave the motor plugged into the drive??? To sum up, we connect the programming board with the shortest wire of the ESC, we connect the LiPo and then turn on the ESC with the inter to modify the parameters. 👍👍👍
Because i had the reverse function set to the mechanical break so the motor did not have to slow such a heavy vehicle, the down side was no reverse.... but also no sheared gears from breaking letting off breaking again and activating reverse while 50 lb truck still rolling forward and boom go diffs ect.
What are the basics to program? Do you have to program motor timing? If yes how do you know what timing is appropriate? Do you need also to program poles according to motor used thankyou
Is your low voltage cut off working properly on yours? If I set mine to cut off at 3.4v it still takes them down to 3v......regardless of how much I program it.
I noticed the asterisk doesnt change to the value I set to. The asterisk is probably the factory setting. Havent installed and ran yet but do you know if the asterisk is supposed to change the setting you choose?
Hey do you know how to update the firmware and download the software for the ZTW with a Mac? Having issues trying to set my parameters for the ZTW Beast Pro 300amp.
Lol mac. There was no update when I had mine. Their customer service sucks and so does the website. What parameters are you setting. Most are settings are backwards from normal escs. Its a pain in the ass.
The esc worked great. They need to be used with motors like poseidon, castle, ztw, hobbywing ect. No tp power, neu, cordova ect motors... the esc cannot run the big high amp draw motors and will burn up. It is same as hobbystar 300a esc. I dont know how it has held up i sold that truck last year. I am considering putting a 300a 12s in my new kraton. And running it on 10s with stock motor.
DO you know if the regular Hobbywing LCD program card will work with this ESC ? Here in Europe only one retailer is selling this ESC and requests 30 Euros extra just for the program card. I would like to convert my 8S MTXL into 12S just like you did.
Holly shit man! what a beast! thanks for sharing mate! subbed to ya
Hi friend to configure the ESC with the board can we leave the motor plugged into the drive??? To sum up, we connect the programming board with the shortest wire of the ESC, we connect the LiPo and then turn on the ESC with the inter to modify the parameters. 👍👍👍
Thats a big badass esc bro!!
Nice I wonder if that esc would be good for a super serpent!
Henry fords rc i have the 200a version coming next week to see if it will go in one of my buggies.
Hi mine just show the model no on the screen. Nothing else happen
hey do you have the coog effect? I have a ZTW 300A regulator with a small addition of gas, how do you set the ESC do you have the timing changed?
why there is no reverse throttle ?
Because i had the reverse function set to the mechanical break so the motor did not have to slow such a heavy vehicle, the down side was no reverse.... but also no sheared gears from breaking letting off breaking again and activating reverse while 50 lb truck still rolling forward and boom go diffs ect.
will this work on a 120a sl beast model esc? i need to turn my voltage cut off down and engine timings badly.
Not sure. Have to check ztw been out of that loop for while. I think if you put the program on the box from ztw it will work but not 100% sure.
Pierre Extensions
What are the basics to program?
Do you have to program motor timing? If yes how do you know what timing is appropriate? Do you need also to program poles according to motor used thankyou
Is your low voltage cut off working properly on yours? If I set mine to cut off at 3.4v it still takes them down to 3v......regardless of how much I program it.
I noticed the asterisk doesnt change to the value I set to. The asterisk is probably the factory setting. Havent installed and ran yet but do you know if the asterisk is supposed to change the setting you choose?
Hey do you know how to update the firmware and download the software for the ZTW with a Mac? Having issues trying to set my parameters for the ZTW Beast Pro 300amp.
Lol mac. There was no update when I had mine. Their customer service sucks and so does the website. What parameters are you setting. Most are settings are backwards from normal escs. Its a pain in the ass.
How is this esc holding up, i wanna put this for speed runs on 12s . Not sure if this can handle it
Tem algum vídeo ensinando como programa esse esc em português PF
Hey man is this ESC any good ? Looks like the hobbystar 300 esc
The esc worked great. They need to be used with motors like poseidon, castle, ztw, hobbywing ect. No tp power, neu, cordova ect motors... the esc cannot run the big high amp draw motors and will burn up. It is same as hobbystar 300a esc. I dont know how it has held up i sold that truck last year. I am considering putting a 300a 12s in my new kraton. And running it on 10s with stock motor.
DO you know if the regular Hobbywing LCD program card will work with this ESC ? Here in Europe only one retailer is selling this ESC and requests 30 Euros extra just for the program card. I would like to convert my 8S MTXL into 12S just like you did.
I just tried and that would be a negative there ghost rider lol
So I'll be ordering mine tomorrow lol