Very nice as proof-of-concept & immediate practical use. Your next task is to make it repairable for maintenance. This means you will need a slightly bigger diameter tube so that you can easily slide out the battery, because no battery ever built is going to live forever, even rechargeable ones such as ni-cd, lith-ion, etc. When that battery dies, you will not be able to easily remove the insides because you glued everything together. So you will need some sort of base end that can come off etc. Hopefully you can build a better version. If you are good at business, you can also make a lot of these and sell at markup.
Аккумулятор 18650 в алюминиевый корпус без изоляции...Будет весело, когда произойдет кз и отвертка либо взорвется, либо потечет аккум... Крайне ненадежно и очень опасно.
@@proknow this is definitely a fire hazard. It's not cus of the aluminium tubing. It's cus the battery contacts are very close with poor solder job. Also did you clean the solder joints after? If not those wires will come loose within 2 yrs and most likely short the battery out. Other than that it looks great! It is highly advised to take extra caution when dealing with batteries!
@@proknow it will become conductor because you did not use any kind of insulation material between that 18650 cell and aluminium tube, also you used non isolated wires (only laquer coating) from that TP4056 to switch , it is horrible work .... you should not be making tools like this, i am tearing my hair watching your video
Hey there! As a tech enthusiast, I totally agree with your suggestion to cover the battery of the DIY electric screwdriver. It's important to prioritize safety and protect the exposed parts. Speaking of handy tools, have you heard about the HOTO Compressed Air Capsule? It's a versatile device that offers powerful vacuuming and blowing capabilities, perfect for keeping your desk and other spaces spotless. Might be worth checking out! 😉
Hello, by following the links I see that the motor is in 12v while the power supply is in 4.2, it is not possible to find a motor of the same type in 5v for example, and suddenly the screwdriver actually allows you to unscrew screws which are tightened a little hard, I am afraid that the motor does not provide the necessary power since it is underpowered, there is an identical 6v motor at 300 rpm, wouldn't that be more efficient?
i have the same motor and yes it is 12v but you supply it with lower voltage. it also has high torque! i also plan to make one but i need a momentary switch not a toggle switch which i still dont have
Based on the title and content, it seems like you're interested in building your own powerful electric screwdriver. While that's definitely a fun DIY project, have you considered the HOTO Compressed Air Capsule? It offers powerful vacuuming and blowing capabilities, which can come in handy for maintaining a spotless desk and cleaning your car's interior. Plus, it's portable and has efficient storage options. Check it out!
Hey {{3}}! Have you considered the HOTO Compressed Air Capsule? It's a compact and versatile device that offers powerful vacuuming and blowing capabilities. With its high vacuum power and multiple accessories, it's perfect for maintaining a spotless desktop, cleaning your car's interior, and even inflating items quickly. Plus, it's lightweight and portable for on-the-go use. Check it out!
Gracias por tu video, pero me puedes decir que cargador necesita esa batería?? Thanks for your video, but can you tell me which charger does that battery need?
Hey there! If you're looking for a powerful electric screwdriver, you might want to check out the DIY N20 Gear Motor project. As for the battery charger, I'd recommend looking for one that supports the battery's voltage and capacity. It's always best to consult the product manual or reach out to the manufacturer for specific recommendations. Happy DIYing! 🛠️
Sir i like you and your arduino project so much specially that robot but i can't have any arduino uno board or raspberry Pi development board so i can't make anything but still o watch all of your videos
Its Jackly JKLY6032 Heres the link : www.flipkart.com/search?q=Jackly%20Screwdriver%20set&otracker=search&otracker1=search&marketplace=FLIPKART&as-show=on&as=off
Why no t solder the ends? And use a key way for the motor shaft to the collet, eventually all the torque will break the super glue and metal with a plastic bushing? Lol at least cut some groves or gimping to provide some sort of friction to it. And why was the battery in backwards??????
Great implementation, congratulations! If you are interested in this topic, you may check a version using 3D printed parts: ruclips.net/video/rySeXWpQ-Bc/видео.html
Very nice as proof-of-concept & immediate practical use. Your next task is to make it repairable for maintenance. This means you will need a slightly bigger diameter tube so that you can easily slide out the battery, because no battery ever built is going to live forever, even rechargeable ones such as ni-cd, lith-ion, etc. When that battery dies, you will not be able to easily remove the insides because you glued everything together. So you will need some sort of base end that can come off etc. Hopefully you can build a better version. If you are good at business, you can also make a lot of these and sell at markup.
Аккумулятор 18650 в алюминиевый корпус без изоляции...Будет весело, когда произойдет кз и отвертка либо взорвется, либо потечет аккум... Крайне ненадежно и очень опасно.
Vvry nice 👍
Premium work true masterpiece keep it up 👍
Thank you 🙌
First like and comment
1st
And
Very nice video
😘
ruclips.net/video/bZ-fLyMHVdc/видео.html 👈its micro screwdriver.
Интересно реализован реверс для моторчика, но я бы добавил кнопку без фиксации для подачи напруги)
Very well made, its compact and rechargeable too, nice.
But the negative part of the battery is fully exposed, you should cover it with some tape.
The Aluminium pipe that i used is not a conductor of electricity.
@@proknowOkay 👍
@@proknow this is definitely a fire hazard. It's not cus of the aluminium tubing. It's cus the battery contacts are very close with poor solder job. Also did you clean the solder joints after? If not those wires will come loose within 2 yrs and most likely short the battery out. Other than that it looks great! It is highly advised to take extra caution when dealing with batteries!
@@proknow it will become conductor because you did not use any kind of insulation material between that 18650 cell and aluminium tube, also you used non isolated wires (only laquer coating) from that TP4056 to switch , it is horrible work .... you should not be making tools like this, i am tearing my hair watching your video
Hey there! As a tech enthusiast, I totally agree with your suggestion to cover the battery of the DIY electric screwdriver. It's important to prioritize safety and protect the exposed parts. Speaking of handy tools, have you heard about the HOTO Compressed Air Capsule? It's a versatile device that offers powerful vacuuming and blowing capabilities, perfect for keeping your desk and other spaces spotless. Might be worth checking out! 😉
Ловко он канцелярским ножом порезал алюминиевый корпус))
Hello, by following the links I see that the motor is in 12v while the power supply is in 4.2, it is not possible to find a motor of the same type in 5v for example, and suddenly the screwdriver actually allows you to unscrew screws which are tightened a little hard, I am afraid that the motor does not provide the necessary power since it is underpowered, there is an identical 6v motor at 300 rpm, wouldn't that be more efficient?
i have the same motor and yes it is 12v but you supply it with lower voltage. it also has high torque! i also plan to make one but i need a momentary switch not a toggle switch which i still dont have
Nice post 👍👍👍👍👍👍👍
На секундный клей к металлу
Очень надежно
Незаизолированный аккумулятор
Очень безопасно
Based on the title and content, it seems like you're interested in building your own powerful electric screwdriver. While that's definitely a fun DIY project, have you considered the HOTO Compressed Air Capsule? It offers powerful vacuuming and blowing capabilities, which can come in handy for maintaining a spotless desk and cleaning your car's interior. Plus, it's portable and has efficient storage options. Check it out!
Nice one.
Nice
ruclips.net/video/bZ-fLyMHVdc/видео.html 👈its micro screwdriver.
Con lo que vale ese motorcito en aquí en argentina ya compramos el destornillador en mercado libre y con envío gratis jejeje
Разбирать потом только при помощи универсального ключа🤣
I like it ✌️✌️
ruclips.net/video/bZ-fLyMHVdc/видео.html 👈its micro screwdriver.
Very nice work
Amazing👍
Hey {{3}}! Have you considered the HOTO Compressed Air Capsule? It's a compact and versatile device that offers powerful vacuuming and blowing capabilities. With its high vacuum power and multiple accessories, it's perfect for maintaining a spotless desktop, cleaning your car's interior, and even inflating items quickly. Plus, it's lightweight and portable for on-the-go use. Check it out!
Use Battery 4v aur motor 12v wov ?
Бля как иностранцы любят суперклей готовы на него всё клеить🤣
Good idea bro..
Good ♥️♥️♥️
Very good
Awesome #BjElectrical
4:14 hey how did you remove that head of that screwdriver? , i cant remove it!
Gracias por tu video, pero me puedes decir que cargador necesita esa batería??
Thanks for your video, but can you tell me which charger does that battery need?
ruclips.net/video/bZ-fLyMHVdc/видео.html 👈its micro screwdriver.
Hey there! If you're looking for a powerful electric screwdriver, you might want to check out the DIY N20 Gear Motor project. As for the battery charger, I'd recommend looking for one that supports the battery's voltage and capacity. It's always best to consult the product manual or reach out to the manufacturer for specific recommendations. Happy DIYing! 🛠️
Bro.pls reply.is this motor powerfull.can it release a tight screw?.what about using rs555 motor
ruclips.net/video/bZ-fLyMHVdc/видео.html 👈its micro screwdriver.
Superb
Sir i like you and your arduino project so much specially that robot but i can't have any arduino uno board or raspberry Pi development board so i can't make anything but still o watch all of your videos
Do you still alive?
How are you cutting those metal shapes????
Using drill, hand saw and File
What is that tool kit you're using? I can't find that small (4mm) adapter anywhere!
Its Jackly JKLY6032
Heres the link : www.flipkart.com/search?q=Jackly%20Screwdriver%20set&otracker=search&otracker1=search&marketplace=FLIPKART&as-show=on&as=off
Bagusnya pakai 2 tombol
Any torque and the glue will tear it to ribbons
Why no t solder the ends? And use a key way for the motor shaft to the collet, eventually all the torque will break the super glue and metal with a plastic bushing? Lol at least cut some groves or gimping to provide some sort of friction to it. And why was the battery in backwards??????
18650 battery bomb
Can you make jet engine by brushless motor and plz show how much upthrust it produce and how much weight it can Left
I will try bro.
Sabshe a6ya kitna voltage me chalega
Please rept
Pake dinamo tamiya bsa ga
Очень хлипкая конструкция .
Hey bro is this possible by normal dc motor? Plz ans me
No it needs gear motor
Ok you are inspired by the wrench... Right?
How disregarding all the safety of the battery and circuit looks like..
👍
Зачем деталюхи дергаешь на камеру??? Очень раздражает.
Kept up
5v??
What’s up
Like to banta hao
N20 DC motor 55rpm is that ok?
yes.
The lower the rpm the more torque the motor will give out...
Why do you don't do giveaways🎁✨ please do
Nice project.. impressive ❤️❤️,btw Motor rpm plz??
350 rpm
@@proknow bro copper wire is open?????
Instant glue is good but use epoxy for a stronger bond
oR JuST sOLdEr
Bro explain about the detailed spec of li ion battery, voltage, input, output
Bro how did u solder two wires on battery??
Pls explain🙏🙏
Maximum voltage 3.7 volt
Minimum voltage 2.7 volt
Charging voltage 4.2 volt, 1 Amp
Shelf loss 15% per year
Needs BMS to charge....
Then that battery never cam out..
3:25
I don't understand the switch can you show us in detail or a diagram
6 pole hai total
2 aage 2 piche 2 bich me
Aage piche Wale ko ❌ connection karenge bich Wale me supply denge
I'm sorry, I didn't see that the nameplate specifies it
ruclips.net/video/bZ-fLyMHVdc/видео.html 👈its micro screwdriver.
What is the switch name
DPDT (Double Pole Double Throw) Switch.....
Hii
Вот это херня. 300 полуляхов из 250
Bhai muje bhi bna ke de do na khrcha me de du ga bolna ok
Please Ripley
В своей версия я использовал подшипниковый узел от HDD ruclips.net/video/z3YOVCJPwHI/видео.html
Maja nhi aya aur acha ho sakta tha
Can you please give me I will give you money 🙏🏻🙏🏻🙏🏻🙏🏻
Bad muzic 🤮🤮
bad english 🤮🤮
Great implementation, congratulations! If you are interested in this topic, you may check a version using 3D printed parts: ruclips.net/video/rySeXWpQ-Bc/видео.html
Nice