Electrical Circuit Basics Part 3 - Resistance and Loads
HTML-код
- Опубликовано: 12 сен 2024
- In part 3 of our electrical circuit basics series, we cover voltage measurement, loads, and resistance in electrical circuits.
A load technically doesn't separate the circuit, but it adds resistance; if you take a voltmeter and put one meter lead on one side of the load and the other lead on the other, you will get a value above 0 volts. On a 120v circuit, you would read 120 volts. That's because voltage measures the potential difference between two different points on a circuit. The load also controls the flow of electrons.
However, if you read voltage between two adjacent points without any loads or separation, you will get 0. A voltage reading across a closed switch will also (usually) equal 0; a closed switch is just a path and doesn't add resistance. However, in the case of rollout switches with carbon buildup or pitted contactors, you can see small, undesigned loads start to form on the switches or contactors.
Higher resistance equals lower amperage; more resistance impedes the flow of electrons, so fewer electrons move.
When you connect a load to a circuit, you need to put it in a place where there are differential charges on each side. In other words, a load can't connect to and from L1; it must connect from L1 and to L2 because there are differences in charges in play.
When you read across an open switch, you will get the total applied voltage so long as the rest of the circuit is intact. (If there were two open switches, then you would read 0 because the rest of the circuit is not intact.)
Assuming that the switch is closed, you would also get the total applied voltage of the circuit if you were to read between two different sides of the load. (However, when the switch is open and you read between two different sides of the load, you would read 0 because the electrons cannot reach the load.) So, you can use your voltmeter by keeping one lead on a known opposite and "walking" the other meter lead through the circuit until you can pinpoint where the switch is open.
Read all the tech tips, take the quizzes, and find our handy calculators at www.hvacrschoo...
thank you for all the great information you provide. I continue to learn so much from the videos and podcasts.
Thank you.
You are a great teacher. I am new to the hvacr business. And I was always confused on how the 240 works and how come it doesn’t have a neutral. But you explain it very clear.
Thank you for this concise explanation of line load and testing through a circuit. Makes so much more sense to me now.
This dude knows how to explain! Great content. Side note, 4.53 the guy filing his nails is epic.
Great video! Do you have any more that discuss in further detail meter usage while looking at a ladder diagram? Specifically "what should I read when I measure between these two points."
I learned better from you Bryan than my own teacher
I watch all your video and broadcast, I like your teaching style.
Great explanation!!
Im falling in love with this 😊
Great Teacher!!!
30 yrs later and I'm paying attention and making the "connections".
Master class!!!!
Good refresher
Great content
Good shit
Why would you have a wire without a load? Wouldn’t you just get rid of it completely instead of it causing circuit to heat up & cause damage? Very new to electrical here. Honestly curious. Thanks y’all.
Thanks
nice video
With the example at around 10min with the two open switches, what if you measured from the line side of the first switch and the load side of the second switch?
You'll get the 120 v
Your video is good but tell that boi to st😂p filing his nails😂
XD
7:19 electric chair?
Nyc
does this guy have an actual school?
Adopt me as your employee!
This was confusing
You have a load in your meter chump! I have stuck my meter leads many times in an electrical socket and it didn't blow up! If you use an analog and have it in ohms and put the leads across a power supply it will blow up! I am privy to that but i did not do it my boss did! Many years ago! If the meter is in the correct designation it will be fine.
does this guy have an actual school?
We are a contractor and have a registered apprenticeship program in Florida.