Here is my channel wish list if you would like to show some support in purchasing some tools or spare parts, it is gratefully appreciated www.amazon.co.uk/hz/wishlist/ls/13BO7QKGAZZV2/ref=nav_wishlist_lists_2?_encoding=UTF8&type=wishlist
Mate, get a dremel tool or a reasonable tool, and get steel wire wheels, or brass wire wheels the flat and cone shaped ones, it cleans the bowls beautifully.
My o ring expanded like that the first time I took it out and got carb spray on it. Really disappointed I walked out of the garage in disgust, then took another look the next morning and the ring had dried and shrank back to proper size - that was about three years ago.
Hiya Mick. Hope ure well. I really like your production technique lol whereas i fumble around in my videos. Great Start :-) I just started a 1989 Hayter 21 i found dumped near where i live 🙂 I bet thats the original plug.
With the carb, I have found putting a small socket underneath the bottom post, supports it as you knock the pin into it. Also, although it's not good to break one of the posts, it still unlikely it will leak because of it.
Micks Mowers Merchandise UK Store below micksmowersthemowerman.myspreadshop.co.uk/men?q=D1 Micks Mowers Merchandise USA Store below micks-mowers-usa.myspreadshop.com/all
Thank you for this video Mick 👍🏻 , a retired gentleman has just put one of these up ( including scarifier ) collecting it Friday. After work , believe the clutch cable is continuing engaged. Any recommendations for where to purchase parts for these. Many thanks
@@themowermanThanks Mick , collected it last night. So have a look at it today. He fired it up for me , but has he said , once it was fired up it will want to start to drive. So going to see if any slack in the cable. But is it worth just replacing it for new cable? Changing the oil? , is the easiest way to just tilt the mower on its back ? To drain.
Hi mick I have a atco 24e 1c when you release works fine then release dead man lever it stops has it should and then jams drive pulling the mower back and going again it’s fine can you help has I’m at a loss with it❤
Yes I mow the lawn stop to empty box and when I want to go engine labours has if brake is on and pulling back a few times will get it going but has got too tedious to use it
No sorry the dead man pulled in labours engine without stalling I release to pull back and then pull in dead man lever sometimes it works some time it dont
I have a qualcast 43s which runs great going forward but rear roller wont pull back i have to drag the mower as the rear roller seems to lock ? Any ideas mick ?
@@jlb361999 fitting this helps www.gardenhirespares.co.uk/genuine-bosch-pinion-plate-assy-f016103210.html?gclid=Cj0KCQjw98ujBhCgARIsAD7QeAibew7lyEH5qtQEkLTqLgZKRq1NNdvvs5nPbITz6--HVBv66vJdCZYaAoOAEALw_wcB
Mick if the viewers say you are not close enough all they have to do is pinch the screen to zoom in ‘very very simple solution’ … some people love a good old moan hey pal? 😉
Here is my channel wish list if you would like to show some support in purchasing some tools or spare parts, it is gratefully appreciated www.amazon.co.uk/hz/wishlist/ls/13BO7QKGAZZV2/ref=nav_wishlist_lists_2?_encoding=UTF8&type=wishlist
Nice work on the Atco Balmoral for 9 years I thought the carb would have been alot worse 👍but you worked your magic and got it back running again.
What a proper buy.Good one Mick.Hello Riley boy high five.All the best to you all.
Your videos are made perfect.
That's a wonderful machine!
Oh it is mate
Spot on Mick well saved 👍👍👍👍
New camera it looks great 👍
Hi Riley boy, nice to see you back. Nice mower Mick
The video just got better now that Riley boy showed up.
Nice work Mick! And hi Riley Boy!
Grass rats yooooo
Excellent find, and Awesome fix mate.
Another thorough video Mick, very informative cheers. Riley boy is shooting up, see you next time 👍
Nice job on the carb Mick, it looked pretty rough.
Hey Riley Boy!!! 👋
Mate, get a dremel tool or a reasonable tool, and get steel wire wheels, or brass wire wheels the flat and cone shaped ones, it cleans the bowls beautifully.
This is a nice clean machine. A carburettor master. Great midstream sample at 34:52. :-) Nice to see Riley
Hi guys another good video thank you for the video
Nice shades there mick 😎 like those ! I'm surprised as rough as that carb looked it fired on the first pull nice 👍
Well at least the mower Man is to fix another reel mower 😂😂
Nice one Mick. Lovely find and great instructional video. That one looks a keeper 😅
My o ring expanded like that the first time I took it out and got carb spray on it. Really disappointed I walked out of the garage in disgust, then took another look the next morning and the ring had dried and shrank back to proper size - that was about three years ago.
Ding dong .
Hiya Mick. Hope ure well. I really like your production technique lol whereas i fumble around in my videos. Great Start :-) I just started a 1989 Hayter 21 i found dumped near where i live 🙂 I bet thats the original plug.
With the carb, I have found putting a small socket underneath the bottom post, supports it as you knock the pin into it.
Also, although it's not good to break one of the posts, it still unlikely it will leak because of it.
Good tip mate
What I think would make a good episode is, how did you get into small engines, age, reason?
Micks Mowers Merchandise UK Store below
micksmowersthemowerman.myspreadshop.co.uk/men?q=D1
Micks Mowers Merchandise USA Store below
micks-mowers-usa.myspreadshop.com/all
TOOLS I USE -
Oil Extraction pump amzn.to/2UBApDI
Fan Blade Bulb amzn.to/39BLI4a
Blade removel tool amzn.to/3nxBVQj
Micro Drill Bits amzn.to/36Jpv0R
Carb Cleaning Files amzn.to/3lH8ESx
Hex Shank Extension Drill Bits Bar Set 1/4" 3/8" 1/2" amzn.to/3oFKHx9
Dewalt DCF887M1- Impact Driver, amzn.to/3oEVcjZ
Lawnmower Rotary Blade Balancer amzn.to/3e6UOWN
Rode WIGO Wireless GO Wireless Microphone amzn.to/2JlRlIN
Neewer 176 LED Light amzn.to/2HaubnJ
Universal Style, Mower Deck clamp for blades amzn.to/31PKygE
Briggs & Stratton Diaphragm and Gasket set amzn.to/3kF8Y3H
GT SONIC 3L Ultrasonic Cleaner amzn.to/2TDdVy9
VEVOR 3L Ultrasonic Cleaner amzn.to/2Gb3PBJ
Stainless Steel Strainer for carb jets in a cleaner amzn.to/3e6CxJ2
i thought the B2lm sre just for the rotaries didn't know you can also use them for cylinder mowers
As long as it's a flat head.. they are different for the Kawasaki..
Yes I’ve got a balmoral 20S have the scarifier but need a mower cassette so as to use both to mow and scarify. Any help appreciated
I don't have one ready.. I think I May have one that needs sharpening
Thank you for this video Mick 👍🏻 , a retired gentleman has just put one of these up ( including scarifier ) collecting it Friday. After work , believe the clutch cable is continuing engaged.
Any recommendations for where to purchase parts for these. Many thanks
Hi mate.. spares are available everywhere.. eBay Amazon and GHS.. any problems or questions just ask..
@@themowermanThanks Mick , collected it last night. So have a look at it today. He fired it up for me , but has he said , once it was fired up it will want to start to drive.
So going to see if any slack in the cable. But is it worth just replacing it for new cable?
Changing the oil? , is the easiest way to just tilt the mower on its back ? To drain.
@@leefenton9477 could be a cable adjustment or new belt.. yeah to change the oil just tip it back
do you have a mower cassette for an Atco Balmoral 20S please?
Do you mean one ready to use?
What manifold do I need please for an AQ148 engine on a qualcast 35s. Wish to fit a tillostan tk instead.
You will fine one on eBay mate
Thanks for the reply. I cant seem to find anything anywhere, what exactly should I be searching for? Cheers again
Hi mick I have a atco 24e 1c when you release works fine then release dead man lever it stops has it should and then jams drive pulling the mower back and going again it’s fine can you help has I’m at a loss with it❤
Can you no move it with the dead man pulled in..
Yes I mow the lawn stop to empty box and when I want to go engine labours has if brake is on and pulling back a few times will get it going but has got too tedious to use it
@@mgtfbluestreak3956 hmmm not seen that before...
No sorry the dead man pulled in labours engine without stalling I release to pull back and then pull in dead man lever sometimes it works some time it dont
I have a qualcast 43s which runs great going forward but rear roller wont pull back i have to drag the mower as the rear roller seems to lock ? Any ideas mick ?
Belt issues or needs the upgrade on the drive
@@themowerman whats the upgrade on the drive ??
@@jlb361999 fitting this helps www.gardenhirespares.co.uk/genuine-bosch-pinion-plate-assy-f016103210.html?gclid=Cj0KCQjw98ujBhCgARIsAD7QeAibew7lyEH5qtQEkLTqLgZKRq1NNdvvs5nPbITz6--HVBv66vJdCZYaAoOAEALw_wcB
@@jlb361999 nice little video for you to watch ruclips.net/video/yOw94E6UrwI/видео.html
Mick if the viewers say you are not close enough all they have to do is pinch the screen to zoom in ‘very very simple solution’ … some people love a good old moan hey pal? 😉
Lol I know