Hi There, I have a general question. I have 2 outputs (heater +cooler), if I set the SV=35 and PV reads as 48, will that go down to 35 by turning on the cooler and in case if it goes lower than 35 (like 30) will that automatically turn on the heater? I need to do all this via RTU in my code. Currently I have another brand, that is not very accurate and I have to program it to either use the heater or cooler and it cannot recognise when to use what. Is this something can be done with Delta products? lease respond me as throughout as possible. Many thanks.
You should be able to see the price once you add it to the cart. This can be viewed from your cart prior to ordering in the upper right hand corner of the site. I hope this helps.
hi, i want run with this temperature controller vfd. as temperature go up its run slow, and if temperature go down it run fast. ? can you explain that ? thanks
These controllers have an RS485 com port that supports MODBUS ASCII/RTU communication protocol, only. Can your Labview software integrate MODBUS protocol?
We SIGNAL CONTROL SYSTEMS are a leading manufacturer of temperature controllers , timers and other industrial controllers in ahmedabad. Email on dobariadhruv@gmail.com for further details.
I have this type of temperature controller but is not working so I want to buy new controller please check hear I have given description of my currant controller please help me which controller I can buy that work like this 1 function : when controller start HEATER on and the temperature reach at sated temperature (Exp. 135 C) 2 function : this is delay time (Exp. 120 Sec.) in this function controller just count sated time 3 function : this is cooling function it will down temperature (Exp. 55 C) with starting FAN 4 function : in this function give Buzzer Sound (Exp. 10 Sec. and controller Will go to off mode or sleep mode
Dharmesh Sony , We SIGNAL CONTROL SYSTEMS are a leading manufacturer of temperature controllers , timers and other industrial controllers in ahmedabad. Email on dobariadhruv@gmail.com for further details.
AJAY KUMAR We SIGNAL CONTROL SYSTEMS are a leading manufacturer of temperature controllers , timers and other industrial controllers. Email on dobariadhruv@gmail.com for further details.
Hello, You should be able to reset the controller by writing hex value 1234 into register at 472AH and 1234 again into register at 474EH. Then repower the DTB controller to complete the default setting. Hope this helps.
Very nice
thanks so much for the help
Welcome
hey, i was wondering if it would be able to connect the rex c100 to arduino, to control him through arduino lcd screen?
greets, nel
Hi There, I have a general question. I have 2 outputs (heater +cooler), if I set the SV=35 and PV reads as 48, will that go down to 35 by turning on the cooler and in case if it goes lower than 35 (like 30) will that automatically turn on the heater?
I need to do all this via RTU in my code. Currently I have another brand, that is not very accurate and I have to program it to either use the heater or cooler and it cannot recognise when to use what. Is this something can be done with Delta products? lease respond me as throughout as possible. Many thanks.
How to remove lock after controller locked
Thanks for video..makes alot better understanding..but you have no prices on your site,when I went to order....
You should be able to see the price once you add it to the cart. This can be viewed from your cart prior to ordering in the upper right hand corner of the site. I hope this helps.
Ok thanks
nice video.,.i need manual please
Plzz sir make the video DBA4848Ro controller video also make plzz .
hi, i want run with this temperature controller vfd. as temperature go up its run slow, and if temperature go down it run fast. ?
can you explain that ?
thanks
Sure, just make the speed reference to the VFD drop with temp rise and vise versa when temp falls. What type of process is this?
Dear sir please temperature controller pxr9 wering with setting.
can we use this controller with labview software...please help.
These controllers have an RS485 com port that supports MODBUS ASCII/RTU communication protocol, only. Can your Labview software integrate MODBUS protocol?
We SIGNAL CONTROL SYSTEMS are a leading manufacturer of temperature controllers , timers and other industrial controllers in ahmedabad.
Email on dobariadhruv@gmail.com for further details.
I have this type of
temperature controller but is not working so I want to buy new
controller please check hear I have given description of my currant
controller please help me which controller I can buy that work like
this
1 function : when
controller start HEATER on and the temperature reach at sated
temperature (Exp. 135 C)
2 function : this is
delay time (Exp. 120 Sec.) in this function controller just count
sated time
3 function : this is
cooling function it will down temperature (Exp. 55 C) with starting
FAN
4 function : in this
function give Buzzer Sound (Exp. 10 Sec. and controller Will go to
off mode or sleep mode
Dharmesh Sony ,
We SIGNAL CONTROL SYSTEMS are a leading manufacturer of temperature controllers , timers and other industrial controllers in ahmedabad.
Email on dobariadhruv@gmail.com for further details.
Hello sir aap Digital pod controller ki sitting ke bare me puri jaankari hindi me bataye
AJAY KUMAR We SIGNAL CONTROL SYSTEMS are a leading manufacturer of temperature controllers , timers and other industrial controllers.
Email on dobariadhruv@gmail.com for further details.
help me. So how reset controler ?
Hello,
You should be able to reset the controller by writing hex value 1234 into register at 472AH and 1234 again into register at 474EH. Then repower the DTB controller to complete the default setting.
Hope this helps.
Yhhhh
Error 6200
DElTD DTK