Thx for sharing! Got mine open, even it was s bit different casing. Mine mixer had a problem with one of the button not working... It was the lower power output. I could live with it and did... for years. I originally found it from the dumpster (OBH NORDICA 800W). It had such problem that the shaft bore (?) was worn out from the plastic part. I saw a slot in the shaft itself, put a piece of metal and and glued it with chemical metal. For six years it lasted. But since there was no way I could place the shaft perfectly center it obviously vibrated and today the patent repair gave up on me. But luckily got just finished the lemon kissel I was making :) I opened it in a good faith for fixing it once again but bro, I just didn't bother to do it... Oh, and in my mixer there was one part on the circuit that was black had three pin on it and it was completely loose... Probably due the vibration. If I only had new parts for it I would have repaired it. Anyway, thx once again and have a good one - everyone! 🙋♂️🇫🇮
Thank you. Had same problem. From factory bad soldered wire. Wasn't able to remove attachment receptacle, but upper side let me solder the wire after removing some mask from board.
Nice video...sir pls bataye inalsa blender k jar and main body ka white plastic coupling Jo fitting k liye use hota hai...vo Kahan se mil sakta hai..pls guide
With my silvercrest ssms 600 i was fortunate i didn t had to weld it , but the chancing of the cable also took time enough , i even re used the existing connextion copper plugs.....wich i had to be verry carefull with
Interesante e tutorial pero tiene el inconveniente que no se ve la operacion que realiza. Debio poner la camara en otra posición. Gracias. Dios te bendiga siempre.
Mate just wondering do you know how i can get that clutch wheel? Mine gone loose while blending any hard stuff it’s stops but the bit inside still spins
Hi. I have a Princess 1000W. It stopped in the middle of mixing lemon salad cucumber. I chopped up the lemon and the cucumber into small pieces. mixed for a few seconds. Then it just stopped. No light in the two switches (blue light when you have power). Now there is no blue light. means no power in. Is there a fuse inside this. What happened. Only a few months old machine.
Hi Guys , Do you know how to open a Model no: POB-2208S (Prima one&only) exactly the same as your video ,but without the dislocating ring that comes off at the front. This one is one solid piece at the front and I cant get it separated from the steel/alu plate to get out the motor . I disassembled the rest ok . Help please !!! Kind regards. Enjoy your day!!
Thx for sharing! Got mine open, even it was s bit different casing.
Mine mixer had a problem with one of the button not working... It was the lower power output. I could live with it and did... for years.
I originally found it from the dumpster (OBH NORDICA 800W). It had such problem that the shaft bore (?) was worn out from the plastic part. I saw a slot in the shaft itself, put a piece of metal and and glued it with chemical metal. For six years it lasted. But since there was no way I could place the shaft perfectly center it obviously vibrated and today the patent repair gave up on me. But luckily got just finished the lemon kissel I was making :)
I opened it in a good faith for fixing it once again but bro, I just didn't bother to do it... Oh, and in my mixer there was one part on the circuit that was black had three pin on it and it was completely loose... Probably due the vibration. If I only had new parts for it I would have repaired it.
Anyway, thx once again and have a good one - everyone! 🙋♂️🇫🇮
Thank you. Had same problem. From factory bad soldered wire. Wasn't able to remove attachment receptacle, but upper side let me solder the wire after removing some mask from board.
Thank you for guide! Helped me to understand how to open mine. Found cold soldering on the board.
Thanks boss for sharing such important video it helped me to repair my blender
Idol na talaga kita kuya ang galing mo sa mga electronic.
Nice video...sir pls bataye inalsa blender k jar and main body ka white plastic coupling Jo fitting k liye use hota hai...vo Kahan se mil sakta hai..pls guide
Thank you very much for the video. I don't have the same blender, but it's a very good guide to try to repair mine.
My is a healthomse brand and open the same.
Excelent , I really appreciate your contribuition
👏
What if the coupler broken? It must be replace? Or it can repair?
Thank you. just what i needed
thank you po for sharing very helpful lalo sa mga gaya ko na d maalam magkalikot ng mga ganyan
Kardeşim Türkiye'den sevgiler
Bu Mueller smartstick ile videon varmi yoksa kasa acilimi aynimi biraz benzio gibi
With my silvercrest ssms 600 i was fortunate i didn t had to weld it , but the chancing of the cable also took time enough , i even re used the existing connextion copper plugs.....wich i had to be verry carefull with
Interesante e tutorial pero tiene el inconveniente que no se ve la operacion que realiza. Debio poner la camara en otra posición. Gracias. Dios te bendiga siempre.
Parece que la abre muy fácil, es como si ya estuviera preparada de antes.
Thanks you.
No meu caso eu uso uma espátula de aço bem fina e introduzir em volta para cortar a cola ,tomar cuidado para não cortar o plástico .
Mate just wondering do you know how i can get that clutch wheel? Mine gone loose while blending any hard stuff it’s stops but the bit inside still spins
fakir mezza blender uses same casing as this blender. thank you.
Hi. I have a Princess 1000W. It stopped in the middle of mixing lemon salad cucumber. I chopped up the lemon and the cucumber into small pieces. mixed for a few seconds. Then it just stopped. No light in the two switches (blue light when you have power). Now there is no blue light. means no power in. Is there a fuse inside this. What happened. Only a few months old machine.
Yes check the fuse inside.
Mate just wondering do you know how i can get that bit ? Mine gone loose while blending any hard stuff it’s stops but the bit inside still spins
White knob is melted in my case. How to fix that? I have murphy 400 watt blender.....white knob basically used to fit blade rod
Terima kasih share
is machine ke bush kaise change kare please us par ek video bna do.
Bro, como hago para desarmar la otra parte de la batidora?
Hi hi sir ! I would like knowing the value of potensiometer( ohm ) , txe
Hi Guys , Do you know how to open a Model no: POB-2208S (Prima one&only) exactly the same as your video ,but without the dislocating ring that comes off at the front. This one is one solid piece at the front and I cant get it separated from the steel/alu plate to get out the motor . I disassembled the rest ok . Help please !!! Kind regards. Enjoy your day!!
Which company made it is
EDY Saudi Arabia
Sinbo 3012 model video send kardy please
may blender makes a very lauod noues wen l use and it is not frome the motor but from the handle blease help 😥
गंगा भाई क्या समझें कि अपने कैसे ठीक किया और क्या ठीक।किया। हां आपके बैक ग्राउंड पर डांस करके-------
2:28 i need the name of that piece, my blender stopped working because that gone broken :c
Magandangq tanghali sir pa pm na man diy back light tester salamat po
Joint part milne ka palace
Mines ilo hand blender. Looks the same..stopped working..
thank you dear, pls we need to know how to repair chopping bowl lid
Me too need to know how to fix the lid
ukuran as nya brpa ?
Ok
Ong xin masin plesse
Where the blender repair
Can't open it. The whole thing is all broken now. Just threw it in the trash
La PRINCESS 221221 para desmontarla hay que romperla, totalmente NO aconsejable.
NO AL USAR Y TIRAR!
Otra cómo está
Your hand is on the way of camera