When you replace the memory chips, note the position - correct orientation - on the RAM card. Did you only do a reball or did you also increase the memory size? Thank you 🤓
Reballing just means resoldering the chips*. Because the solder (which is those little solder balls hence why its called reballing) can get loose over time. The RAM chips are fine they just dont have proper contact with the board. So after resoldering (reballing) they work properly.
@@Mico605 Genius, I didn't ask that. I asked how he knows which memory chip should reball. By the way, I own a Jovy RE-7500 infrared station. Don't teach me how to do rework.
Did your stencil keep moving while you applied solder paste? Interesting video. Those balls made with solder paste looks as good as normal solder balls!
Если у тебя есть лишняя материнка, попробуй заменить слот ddr2. Операция ооочень моторная и сложная, но реально полезная. У меня щас один такой пациент, вырвать сломанный слот смог, а с донорского пока не получается без повреждений снять. Если придумаю как, то запишу видос. На Ютубе не встречал нормальных видео как снять слот.
@@maxon17 Да, я гладел на него недавно и думаю себе - этож как эту заразу выпаять-то если вдруг понадобилась? Большая, массивная - штырьков как у собаки блох. Все что приходит в голову это залить его сплавом розе и по кругу прогревать елозя паяльником. Ибо фен может просто расплавить пластик с другой стороны.
Hola muy buen video me podes decir a qué temperatura trabajaste y en qué velocidad del viento? Y me podes decir qué modelo de microscopio electrónico usaste? Mil gracias
You can, but there's less room for error with less solder. 0.3 solder balls will have 0.15 of "slop" inside the holes of the solder mask/stencil so you'll have to pay mind to that.
If you noticed, there's a raised "rib" on the chips between the solder contact points, so that means the solder contacts will have less solder to bridge that gap if you use smaller balls...
Тоже некоторое время назад спрашивал себя почему на видео не уточняют температуру, потом мне обьеснили что у каждого станция откалибрована по разному, а у многи вобще без калибровки, раздница может достигать 50°C.
@@pauk7700 касаемо температуры в целом - согласен, ведь дистанция, скорость потока воздуха, интенсивность "мотыляния" короче это дело чувств "набитой руки"
ddr2 в декабре 2018... Боже мой, да за 25 килорублей можно взять хороший ноут на последнем поколении i3, перекрывает все нужды кроме поиграть. А для поиграть можно и адаптер для видеокарты купить под USB type C и ее подержанную у майнеров, не на 100% будет работать но все же лучше встройки (которая там и так неплоха). Или взять на AMD Ryzen, там в бюджетных хорошая встройка, можно и в Fortnite поиграть.
@@pauk7700 Если есть паяльная станция и руки не из жопы, а также желание подзаработать - килорубли найдутся. По Type C работает, но не на всех видах, нужно читать спецификацию. Должны работать на новом поколении (отмечен значком "молнии") работают нормально, так как от thunderbolt отличаются только самим разъемом.
Nice video. I have just replaced 3x vram chips on a gtx1080 i bought for 30 bucks from a junkyard. The card works like a charm. 👍👍
Bro, I have a question about of your gtx 1080, the Vcard show a picture(works) when did you buy it?
@@danielbuitrago3029 when someone starts a sentence with "Bro", you're automatically disqualified from an intelligent answer lol
Would you please tell us the speed of blower and temperatur??
@@bantalmenyusuicom The speed of blower is and the temperature is
I learn by watching, I gain experience by doing. Experience is what pays the bills.
Beleza! Depois desse vídeo estou conseguindo dar manutenção nas memórias DDR2 de notebook! Thank you very much!!!
Amigo onde vc está atendendo? Tenho aqui 1 kit de memórias da DDR2 da Corsair , memorias excelente mas precisa de reparo!
0:20 that REMINDS ME! I've been _meaning_ to get a shirt for some time now that says: "I VOID WARRANTIES!" 😎😅
When you replace the memory chips, note the position - correct orientation - on the RAM card. Did you only do a reball or did you also increase the memory size? Thank you 🤓
hello, i know this method, but in fact how do you find witch memory is damaged???! thank's for reply
None were damaged, he did it just to show us all, check the memory installed at the start of the video and at the end!
Try to use memtest86 maybe it’s will tells u
Voltage injection
Excellent video! Thank you very much for sharing, very helpful! 👍
Nice bro I got to learn 💯 how to rebuild copu chips and ram memory it's only ways that pc abd laptop comes back to life. Keep safe
Hard work 💪.
How did you know which memory chip is defect? There is 8 pcs and you reball only two of them. How to diagnostic defect chip?
Reballing just means resoldering the chips*. Because the solder (which is those little solder balls hence why its called reballing) can get loose over time. The RAM chips are fine they just dont have proper contact with the board. So after resoldering (reballing) they work properly.
@@Mico605 Genius, I didn't ask that. I asked how he knows which memory chip should reball. By the way, I own a Jovy RE-7500 infrared station. Don't teach me how to do rework.
@@riotintomaršsadrine You are an idiot, getting offended so easily. Small brain. No one cares what rework station you own.
Genius,thank you for that video !
Did your stencil keep moving while you applied solder paste? Interesting video. Those balls made with solder paste looks as good as normal solder balls!
True, that's exactly what I spotted
@@averyoldRUclipsuser The ic moved with the stencil. Did not misalign
Give us another video on how to know which ram chip is faulty
Если у тебя есть лишняя материнка, попробуй заменить слот ddr2. Операция ооочень моторная и сложная, но реально полезная. У меня щас один такой пациент, вырвать сломанный слот смог, а с донорского пока не получается без повреждений снять. Если придумаю как, то запишу видос. На Ютубе не встречал нормальных видео как снять слот.
Нужно будет попробовать! Я так предполагаю что понадобится нижний подогрев, сплав розе и терпение. Проще конечно же новый установить ;)
@@pauk7700 Все правильно, с радостью купил бы, только в моем городе негде.
Franzice или просто нужна ик станция с хорошим верхом и пайкой по профилю. И никаких проблем.;-)
Эх сладкие сны, у меня пока-что вершина технологического совершенства - это паяльный фен)
@@maxon17 Да, я гладел на него недавно и думаю себе - этож как эту заразу выпаять-то если вдруг понадобилась? Большая, массивная - штырьков как у собаки блох. Все что приходит в голову это залить его сплавом розе и по кругу прогревать елозя паяльником. Ибо фен может просто расплавить пластик с другой стороны.
This is what my professional before 8 years
Very good video. Thank you.
Nice !!!
круто!!!!!!!!
нужно было еще указать марки флюсов ,думаю не многие их знают (в том числе и я) !
Спасибо! Флюс китайский amtech nc-559, тот что в паяльной пасте не знаю
что бы с шариками дело было быстро сыпь на плоскость под углом или опалубку слегка потряс, постучал (сыпь не жалей) стянул все шары в лузах.
Nice work xD
GG 🔥🔥🔥
New freind here master
What temperature is used ?
350 celcius
Thanks for your video
Best video ever, thanks Nice to practice microsolder
Bien el video compañero pero mi pregunta dónde consigo stensil para Acer rebaling ala memoria ram
Hola muy buen video me podes decir a qué temperatura trabajaste y en qué velocidad del viento? Y me podes decir qué modelo de microscopio electrónico usaste? Mil gracias
Non ti capisco
And the question remains, how do you figure out which chips are bad on a gpu that will not run a game :)
Bad chips often get very hot, simply touching them will tell you which are bad and good.
You can use MATS/MODS to detect the chip.
how long of heat and what temperature?
Sir where did I buy this stencil
Amazon...
Temperatur of station Air?
Show de bola gostei
how to know which chip is failing
Мне понравилось, особено что проверил работает ли после реболла!
Que comprar as telas de rebali da memória
Em quanto segundo é tempo
Please I need name for all tools used here
Saludos ..donde conseguiste ese soporte para el raballing..gracias
Next do a gpu!
+1 subscriber✋👍
Can I use 0.30m balls
You can, but there's less room for error with less solder. 0.3 solder balls will have 0.15 of "slop" inside the holes of the solder mask/stencil so you'll have to pay mind to that.
If you noticed, there's a raised "rib" on the chips between the solder contact points, so that means the solder contacts will have less solder to bridge that gap if you use smaller balls...
Good voy
Класс очень залипательно
I Ram 8 write
👍👍👍👌👌👌👌😱😱😱🙌🙌😁😁
Мой тебе совет. Хотя бы подписывай при монтаже, что и как делаешь. Иначе ничего не понятно
Уже в процессе, через Ютуб сервис, не хотел лишнию дорожку в Sony Vegas занимать ;)
Там вроде все понятно - но хотелось бы видеть температуры например того же фена
Тоже некоторое время назад спрашивал себя почему на видео не уточняют температуру, потом мне обьеснили что у каждого станция откалибрована по разному, а у многи вобще без калибровки, раздница может достигать 50°C.
@@pauk7700 мне один диванный эксперт недавно говорил, что погрешность в 5°C. - смертельна и непростительна =))
@@pauk7700 касаемо температуры в целом - согласен, ведь дистанция, скорость потока воздуха, интенсивность "мотыляния" короче это дело чувств "набитой руки"
ddr2 в декабре 2018... Боже мой, да за 25 килорублей можно взять хороший ноут на последнем поколении i3, перекрывает все нужды кроме поиграть. А для поиграть можно и адаптер для видеокарты купить под USB type C и ее подержанную у майнеров, не на 100% будет работать но все же лучше встройки (которая там и так неплоха). Или взять на AMD Ryzen, там в бюджетных хорошая встройка, можно и в Fortnite поиграть.
Не у всех есть килорубли, вт и приходится на ddr2 сидеть. Технология с type C не работает!
@@pauk7700 Если есть паяльная станция и руки не из жопы, а также желание подзаработать - килорубли найдутся. По Type C работает, но не на всех видах, нужно читать спецификацию. Должны работать на новом поколении (отмечен значком "молнии") работают нормально, так как от thunderbolt отличаются только самим разъемом.
I guess you did that for fun cause the amount of time spent onto reballing such a cheap RAM stick doesn't worth it imo.
For fun and for make a video