doosan Dx 135 monitor panel has a black out it d'ont switch Power ON it has get water in it. How can do it on any idea pls , and who can repaired this I'm from MAURITIUS 🇲🇺🇲🇺 let know pls thanks in advance.
Hi, to carry out its repair and check, you should bring it to Argentina, a bit far away, it is a somewhat delicate piece of equipment and you must know a lot about electronics and have information. What I can recommend is that as soon as possible you disconnect the battery and remove the panel, you have to disassemble the complete head (HMI Panel), and clean and wash its plates with isopropyl alcohol, and then extinguish the moisture with compressed air and leave it for several hours exposed to the sun, so that there is no moisture left, then reconnect it to perform a test, if it does not turn on I can confirm that the internal electronics of the board is damaged... We must proceed to check its internal source. Thank you Best Regards....!!
Hi, I have to look at the notes that I have at the time I intervened on this panel... I look at the data of the +Vcc and GND pins and I will pass them on to you.....
@@sbelectronicaindustrial6652 el panel enciende pero la pantalla enciende su panel de led pero no hay imagen. Creo que la falla está en la tarjeta interna que posee la que va colocada en el peine. De paso cuando enciende se prende un led rojo interno y el buzer queda sonando permanentemente. Al principio encendía, se iniciaba el programa de la pantalla, funcionaba por un rato y se tildaba. Quedaba congelada la imagen. Lo apagabas, encendías y volvía a hacer lo mismo. Hasta que dejó de dar imagen completamente.
Hi...!! Cv Hengki 16,I'm telling you about this panel in particular, it was received with a Fatal failure... The problem was that the backhoe machine fell into a ravine on the banks of the river, causing the complete subsidence. The panel was completely shorted, it took six months to restore it, until that finally he was able to lift it. I calculate that your problem is not so serious, but I recommend you start with the review of the input source, it is looking at the main connector from the front to your right, there is an important voltage regulator, and a set of diodes, and voltage suppressors with some varistors, you have to take the measurements if they are correct and check that there is no shorted component, always before turning on and performing tests on the panel it is convenient to remove the plate that is in the Slot with its memories and microprocessor.
Good work 👍
Have a WhatsApp??
doosan Dx 135 monitor panel has a black out it d'ont switch Power ON it has get water in it. How can do it on any idea pls , and who can repaired this I'm from MAURITIUS 🇲🇺🇲🇺 let know pls thanks in advance.
Hi, to carry out its repair and check, you should bring it to Argentina, a bit far away, it is a somewhat delicate piece of equipment and you must know a lot about electronics and have information.
What I can recommend is that as soon as possible you disconnect the battery and remove the panel, you have to disassemble the complete head (HMI Panel), and clean and wash its plates with isopropyl alcohol, and then extinguish the moisture with compressed air and leave it for several hours exposed to the sun, so that there is no moisture left, then reconnect it to perform a test, if it does not turn on I can confirm that the internal electronics of the board is damaged... We must proceed to check its internal source.
Thank you Best Regards....!!
Que tal amigo donde están ubicados tengo un monitor con problemas
Hola estoy en la Pcia. de Buenos Aires....
Could you show me how to turn monitor panel on? Plus and min cable
Hi, I have to look at the notes that I have at the time I intervened on this panel... I look at the data of the +Vcc and GND pins and I will pass them on to you.....
Same thing please 🙏 send me too ,because i need to test my panel too
Ami tambien me lo pasan porfa
اناباحب😴😁😁😁
Thank you...!!
Hola amigo. Donde estas ubicado. Soy de Argentina y tengo un monitor de estos con una falla.
Hola, que tal, si también estoy ubicado en Argentina... que fallo presente tu Panel ...??
@@sbelectronicaindustrial6652 el panel enciende pero la pantalla enciende su panel de led pero no hay imagen. Creo que la falla está en la tarjeta interna que posee la que va colocada en el peine. De paso cuando enciende se prende un led rojo interno y el buzer queda sonando permanentemente. Al principio encendía, se iniciaba el programa de la pantalla, funcionaba por un rato y se tildaba. Quedaba congelada la imagen. Lo apagabas, encendías y volvía a hacer lo mismo. Hasta que dejó de dar imagen completamente.
Si tu panel se encuentra con un Fallo Fatal en este momento.......
I have a problem that the gauge panel won't turn on...I want to learn from you
Hi...!! Cv Hengki 16,I'm telling you about this panel in particular, it was received with a Fatal failure... The problem was that the backhoe machine fell into a ravine on the banks of the river, causing the complete subsidence. The panel was completely shorted, it took six months to restore it, until that finally he was able to lift it. I calculate that your problem is not so serious, but I recommend you start with the review of the input source, it is looking at the main connector from the front to your right, there is an important voltage regulator, and a set of diodes, and voltage suppressors with some varistors, you have to take the measurements if they are correct and check that there is no shorted component, always before turning on and performing tests on the panel it is convenient to remove the plate that is in the Slot with its memories and microprocessor.
Holaas
Hi...!!
Me mandas tu wsp por favor
Hola de donde eres...?? O en que zona estáa...??