Luke Skywalker Lightsaber V2 DIY how to build guide .
HTML-код
- Опубликовано: 14 окт 2024
- How to build a Luke Skywalker Return of the Jedi V2 Lightsaber from junk.
The DIY Luke Skywalker Hero V2
“As usual made from junk”
No 3D Printers were used, or harmed when making this.
If you enjoy this video, or find it useful then please don’t forget to click the like tab and please subscribe if you wish to see similar future content. Please also check out some of my other weird and wonderful videos. Thank you.
“Right let’s do this!”
Tools
Small Hacksaw
Hand drill
Plyers
Tape measure
Duct tape
Super glue
Epoxy glue
Black permanent marker
Slim fine paint brush
& some Sandpaper
Materials /component parts needed
2 - T-LIGHTS.
9- large metal washers 35mm.
1medium washer
2 -Compactor Bath hooks “Best lock” 07.1cm.
1 medium D-ring.
1- chrome stunt peg cut to size - or a chrome cylinder 3.5. diameter, 3 and half inch long.
1- Walking stick /chair leg, rubber ferrule 22mm.
1- metal biscuit tin or gift set tin. Cut base to 5 inches by 50mm.
1- Paper stapler metal parts cut to 6mm.
1-Plasterboard spring toggle fixings anchor M4
1-Mini Bottle Opener Keyring Tool Metal Chain Portable Novelty Beer Jar Bar Claw
10 pack of open cable rubber Grommets. 25mm.
10 pack of chrome curtain rings 16-19mm.
1 Wardrobe hanging rail pipe, 2mm diameter approx. Cut to 6inch long.
1¾” Rubber splash preventing tap flexible kitchen nozzle.
1 black rubber bath/sink plug 1 1/2”.
1 Tectite sprint copper push-fit Equal coupler 10mm.
1 stainless steel soap liquid lotion bottles nozzle replacement. dispenser pump head. Thread size 28/400.
1 Stainless Steel 38mm OD Sanitary pipe elf Ferrule 1.5” Clamp.
1. Base pummel
Drill a hole in one of the Compactor Bath hooks nobs
Take the centre part out of the other one and place small bits of plastic card into the 5 cavities’ around the edge. Spread Epoxy glue around the edge and slot the two parts together and let it set for an hour
Take the 2 T-lights and remove the candles.
Place 2 washers in one and 3 washers in the other.
Pore the epoxy into both, until level with the last washers and let it set for an hour. Cut the T-Lights down until level with the top washers.
Drill a hole in the base of the T-Light that has 3 washers.
Match up the holes from the T-light that has the 3 washers and the joined bath hook nobs and glue with epoxy. Let it set for 3 hours.
Take the other T-Light with 2 washers and glue with epoxy to the other side of the joined bath hook nob.
Leave for 3 hours.
Drill 2 holes with a small drill bit on either side of one of the protruding parts of the pummel. Insert your
D-ring with plyers and pinch together.
2. Glaflex part
Take your chrome cylinder stunt peg and using epoxy, glue the tin round it at one end, leveeing 5 mm of the cylinder showing at the end. Tape the tin in place and leave to set for 5 hours approx.
Take the cut down paper stapler part and glue it over the join of the tin part with the epoxy. Tape it down to secure it, until it sets. Leave for 5 hours.
Take apart the plaster board toggle. Keep the inside piece and the hinge part. Cut of the end of the pudding spoon. 50mm long. Connect the toggle part to the spoon end part with super glue. This will form your Graflex clamp toggle part. Then super glue it to the side of the stapler part by placing a small, thin sheet of rubber
in-between to form a tighter seal. You can use leftover rubber from the bath hook part.
3. Black and silver mid-section part
Take the sink tap hose and thread it through the rubber cable Gromets and curtain rings. Lubricate the wardrobe hanging rail pipe and push it through the large hole end of the rubber hose, all the way through.
4. Mid-admitter part
Take your black sink Plug and sand it’s an even disk shape all round. Remove the hoop and make a hole in the centre. Superglue a large washer over the recess part of the plug. Super glue a medium washer over the other end, sandwiching the rubber plug in the middle.
6. End admitter part.
Using Epoxy glue set the self-grip pluming pipe into the chrome soap pump part. Tape the top part of the soap pump part to create a tight seal with epoxy into the Sanitary pipe elf Ferrule admitter part. Set a lark washer on the top of the end admitter part to finish it off.
This is brilliant. I’m collecting the parts at the moment . Thank you so much 👍
Teach me your ways, o wise one
dude!! that has got to be one of the best tutorials i have seen 👊👊👊 i have to get the materials and make one 👍👍👍
Impressive...
Most impressive.
Cant stop watching this . It looks amazing I'm trying to get some of the parts together and eventually try to come up with something 😊
Hi ,
Thanks for your comments .
Please Post your photos of your build on here if you give it a go 👍
facebook.com/groups/938046822894911/?ref=share
Or
facebook.com/groups/101410236566990/?ref=share
This is amazing. Great job recreating it from easily obtainable parts.
Can you make whole tutorial to the lightsaber control box?
Amazing! I watched the obi wan build, that was ace...this is perfect, thanks for the detail
Wow and what I can’t understand is why you haven’t had more likes ? I enjoyed it anyway . Thanks 👍
Thank you . I suppose it’s not for everyone? I
Really enjoying making those videos anyway.
Amazing thanks will track down all the bits and give it ago
Awesome video. Thank you so much for sharing how you built that sweet lightsaber. This style has always been my favorite.
it look seriously amazing
Thanks for your comments
Please share with everyone 👍
Pleas also check out my DIY fully working Android Star Trek Communicator 👍
ruclips.net/video/3e08WWPOQ10/видео.html
This is great DIY. Thanks for sharing
Oh wow that is Awesome.can’t wait to build my.
I might actually use that flexible water spout to make a DH-17. It seems like a good candidate.
I quite liked this. Thanks
Hi
Thanks
I appreciate you feed back .please subscribe in you haven’t already .
Please check out my other short home build creation vids 👍
Including the first ever real fully Woking Star Trek Communicator smart phone . 👍
ruclips.net/video/3e08WWPOQ10/видео.html
Awesome wow I want to try this
Please do. It’s so easy. Give it a go definitely 👍
Well its about time this was made
Do I get a like👍😄
@@thethe6232 well yeah I guess the wait was worth it
@@hyper-link7540
Doing Anakins new hope lightsaber soon .👍
@@thethe6232 Cool can wait to see it 🖖🏾👍🏾
I have watched this video several times and am just amazed at all of the parts used. In regards to a couple of the parts, I am really curious about the part used for the top emitter? What brand and size were used? Also, not sure if you mentioned it, but what kind of stapler did you use for the control box? Again, really awesome and your parts assembly and finds are really awesome. In all honesty, I would never of thought of such things like the stapler, the soap dispenser and the car parts. As Darth Vader said, impressive,most impressive!!!!!
Size 32 Mm
www.ebay.co.uk/itm/322698364155
Size small
www.ebay.co.uk/itm/SMALL-LARGE-STAPLERS-Pocket-Desktop-Desk-School-Work-Office-Paper-Stationery-/312360575308?mkcid=16&mkevt=1&_trksid=p2349624.m2548.l6249&mkrid=710-127635-2958-0
hi there the the it would realy help me if you could make a video on makeing the controll box i mean like how you made it so the top is bent flat
Hi thanks fir commenting on both my sabre videos 👍 I do plan to do. Videos in making each piece soon . 👍
@@thethe6232 thank you master :) i will not use this knowledge to become a sith lord :)
This parts list is much appreciated, but I have some confusion about the dimensions of the parts in the description. What's the OD of the curtain rail, I would guess 19mm, but can't see how curtain rings would fit over that at 16mm ID. Did you have links to the parts at all? Cheers in advance.
Hi
Appreciate your comments .
No the parts just slot together , no linking. 19mm curtain rings , but they fit because the rubber hose is pushed out thicker by the pipe inside it, making it a tighter fit 👍 hope that answers your questions.
Thanks again .
This is amazing ! Can you do a obi wan video like this
ruclips.net/video/2hh1mE4Ob7o/видео.html
I might actually cast some of these parts in aluminum using 3D printed templates, so I get all metal and an easier time finding parts. Especially the emitter, pommel, and control box so I don't have to murder a stapler for every Graflex band lightsaber I make!
Hi
well
My Chanel is really about up-cycling parts from old everyday item and turning them into something els, but thanks for watching 👍
Hey , I’m a big fan of this guy and his take on home made sabres builds . Very original. If your thing is 3D printing , I’m guessing these vids aren’t for you !
@@thedonn5861 I'm only gonna cast parts that are difficult to find.
Can you give a bit more information about the circuit board? Which one did you buy and from where? because i cannot find a similar one like in the video.
Amstrad CPC's Computer Expansion Board Printed Circuit Board with 4 MX4 Slots
www.ebay.co.uk/itm/193940887550?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=0g3NYJ1ZRBW&sssrc=2349624&ssuid=AiCXDDl9R2G&var=&widget_ver=artemis&media=COPY
@@thethe6232 Thx, Keep up the good work. You're amazing.
A lot of the principles applied here could apply to the Obi-Wan lightsaber.
Brilliant ❤
Where did you get that flexible water spout? I won't use it for a lightsaber, but I'll use it for a DH-17 blaster.
Hi , yes I can see the similarity ,
but I would have to say regarding the flexible water spout
“Aren’t you a little short for a DH-17 blaster”👍
Only my opinion but I think it would be the wrong scale in relation to the actual prop.
Anyway I got it from one of those old fashioned traditional style hardware stores . The type of shop that sells all kind of Gadgets , tools and pots and pans 👍
Hi this is the UK eBay link below , but if you live els where, just tips
in ro
Your eBay (rubber flexible large rubber tap swirl or nozzle Kitchen aid 👍 )
www.ebay.co.uk/itm/FLEXIBLE-LARGE-RUBBER-TAP-SWIRL-NOZZLE-3-4-Kitchen-Bathroom-Anti-Splash-Aid-/191914852339?mkcid=16&mkevt=1&_trksid=p2349624.m2548.l6249&mkrid=710-127635-2958-0
@@thethe6232 Thanks.
I like the end result, but because you don't show the full assembly, its hard to understand how it all goes together, and reading the instructions without pictures is confusing as well.
you should make the tesseract from the marvel movies and if you do, if you want can I pls have a shout out?
Hi , great suggestion 👍
Yes, I definitely will give you a shout out if i do that build in the future.
@@thethe6232 thank you your videos are the best :)
The DIY Luke Skywalker Hero V2
“As usual made from junk”
No 3D Printers were used, or harmed when making this.
If you enjoy this video, or find it useful then please don’t forget to click the like tab and please subscribe if you wish to see similar future content. Please also check out some of my other weird and wonderful videos. Thank you.
“Right let’s do this!”
Tools
Small Hacksaw
Hand drill
Plyers
Tape measure
Duct tape
Super glue
Epoxy glue
Black permanent marker
Slim fine paint brush
& some Sandpaper
Materials /component parts needed
2 - T-LIGHTS.
9- large metal washers 35mm.
1medium washer
2 -Compactor Bath hooks “Best lock” 07.1cm.
1 medium D-ring.
1- chrome stunt peg cut to size - or a chrome cylinder 3.5. diameter, 3 and half inch long.
1- Walking stick /chair leg, rubber ferrule 22mm.
1- metal biscuit tin or gift set tin. Cut base to 5 inches by 50mm.
1- Paper stapler metal parts cut to 6mm.
1-Plasterboard spring toggle fixings anchor M4
1-Mini Bottle Opener Keyring Tool Metal Chain Portable Novelty Beer Jar Bar Claw
10 pack of open cable rubber Grommets. 25mm.
10 pack of chrome curtain rings 16-19mm.
1 Wardrobe hanging rail pipe, 2mm diameter approx. Cut to 6inch long.
1¾” Rubber splash preventing tap flexible kitchen nozzle.
1 black rubber bath/sink plug 1 1/2”.
1 Tectite sprint copper push-fit Equal coupler 10mm.
1 stainless steel soap liquid lotion bottles nozzle replacement. dispenser pump head. Thread size 28/400.
1 Stainless Steel 38mm OD Sanitary pipe elf Ferrule 1.5” Clamp.
1. Base pummel
Drill a hole in one of the Compactor Bath hooks nobs
Take the centre part out of the other one and place small bits of plastic card into the 5 cavities’ around the edge. Spread Epoxy glue around the edge and slot the two parts together and let it set for an hour
Take the 2 T-lights and remove the candles.
Place 2 washers in one and 3 washers in the other.
Pore the epoxy into both, until level with the last washers and let it set for an hour. Cut the T-Lights down until level with the top washers.
Drill a hole in the base of the T-Light that has 3 washers.
Match up the holes from the T-light that has the 3 washers and the joined bath hook nobs and glue with epoxy. Let it set for 3 hours.
Take the other T-Light with 2 washers and glue with epoxy to the other side of the joined bath hook nob.
Leave for 3 hours.
Drill 2 holes with a small drill bit on either side of one of the protruding parts of the pummel. Insert your
D-ring with plyers and pinch together.
2. Glaflex part
Take your chrome cylinder stunt peg and using epoxy, glue the tin round it at one end, leveeing 5 mm of the cylinder showing at the end. Tape the tin in place and leave to set for 5 hours approx.
Take the cut down paper stapler part and glue it over the join of the tin part with the epoxy. Tape it down to secure it, until it sets. Leave for 5 hours.
Take apart the plaster board toggle. Keep the inside piece and the hinge part. Cut of the end of the pudding spoon. 50mm long. Connect the toggle part to the spoon end part with super glue. This will form your Graflex clamp toggle part. Then super glue it to the side of the stapler part by placing a small, thin sheet of rubber
in-between to form a tighter seal. You can use leftover rubber from the bath hook part.
3. Black and silver mid-section part
Take the sink tap hose and thread it through the rubber cable Gromets and curtain rings. Lubricate the wardrobe hanging rail pipe and push it through the large hole end of the rubber hose, all the way through.
4. Mid-admitter part
Take your black sink Plug and sand it’s an even disk shape all round. Remove the hoop and make a hole in the centre. Superglue a large washer over the recess part of the plug. Super glue a medium washer over the other end, sandwiching the rubber plug in the middle.
6. End admitter part.
Using Epoxy glue set the self-grip pluming pipe into the chrome soap pump part. Tape the top part of the soap pump part to create a tight seal with epoxy into the Sanitary pipe elf Ferrule admitter part. Set a lark washer on the top of the end admitter part to finish it off.
Where do you recommend I look for these pieces, I have a B&Q near by is there any other places I could look?
Yes, B&Q is good . Try those old fashioned discount hardware shops that self bits and bobs too. eBay is also good for those more harder to find items 👍 Glad to hear you are going to build your own . 👍
Can you make lukes lightsaber but it can light up?
Hi
No, this vid is just about making realistic props . I don’t do light up sabres .
Thanks for watching. 👍
@@thethe6232 ok but can you make like a whole tutorial for the control box? I found it so cool
Hey make Reyflex lightsaber hilt from episode IX
Is episode IX Canon 😆😛😝
@@thethe6232 looks cool and also modify from original Luke skywalker lightsaber i plan to make Reyflex in home
Quoue:
"1 Wardrobe hanging rail pipe, 2mm diameter approx. Cut to 6inch long."
Surely 2mm is a typo??
Is there anything at the heart of it? Dowel / rod etc ?
Yes , a threaded steel pluming bar .
Available at any hardware store .
@@thethe6232 thanks so much
@@obirobkenobi3599 no problem
Let me know if there is anything I can help with . Are you building one ? 👍
@@thethe6232 I’m amassing the parts currently. Had a few issues ordering things online (sizes etc) and I think most of it is enroute . Do the rubber grommets have a groove on them or are they a solid ring ?
@@obirobkenobi3599
Re: the rubber Caleb rings “Grommets”
Yes they are groves, but I turn them inside out , so grove on the inside 👍
Also use less curtain rings and grommets than I did .I made that part slightly too Long in proportion to the original V2 ,
Walkman diy guardians of the galaxy case phone huawei diy
Hey make Darth revan lightsaber hilt
Never showed the bar running through middle! :/
Check out my first Obi wan vid 👍
@@thethe6232 10 pack of open cable rubber Grommets. 25mm.
10 pack of chrome curtain rings 16-19mm.
I don't understand these measurements?!?! How can these be different diameters when they slide on the same piece?
@@stokesy_SWFC trust me . 👍
Are the details in the comment section?
Yes, please take a look. Hope you find it helpful 👍
isnt that battlefront 2 luke's saber
Not sure . 👍
You must not be older than 18
@@ItzNovaTastic
Thanks