When you open the gate, the safety circuit disconnects and the lift stops. That's why you have to close the gate before the lift will move. If you open the gate while the lift is moving, it counts as an unauthorised opening and the lift stops or goes out of service, it went out of service in this case. It goes out of service to prevent unauthorised lift surfing. An authorised opening is when the doors open while the lift is inactive at a floor. The reason why the lift engineer asked you to close the gate was to connect the safety circuit and allow the lift to be manually moved using inspection mode, aka lift surfing.
I hate it when it happens. I would never get stuck in the elevators in Moscow, Russia. In London, UK. I got stuck twice for few seconds, the street elevator at North Greenwich Underground Station and the express elevator at an apartment building.
5:11 Yes , this is the result if you do so. They have warned you. A wonder that the company did not charge you for that rescue. When the elevator is modernized, often they have simpler logic. Means when the elevator arrived close to the destination floor and starts levelling, its a small underprogramm that says " start levelling for (lets say)5 seconds, open interlockcurve ( in german riegelkurve... a metall c shaped device ,motor or magnetic powered, that presses against the roll at the doorlock to release mechanical the door and interlockswitch), then activate magnet/motor to release the door, reset/ go back to next call and wait for doors closed... But if this program gets interrupted due too early opening the inner door the logic blocks for safety. The lift needs to be closed and resetted manually, that the logic thinks the cabin is correct. Then just place any different call. This happens when old elevators get renewed the easiest way, without adding a led tapemeasure( this tape or wheel from plastic with black lines or metall with holes with a infrared lightbarrierfork ( that the logic knows the absolute position of the cabin in the shaft), because the old shaft/ machine whatever may not support this new technique due space... or the owner just didnt want to pay a complete change of the system andvthey added just the necessary parts to meet code. But however if you use unasked someones elevator, follow the attached rules and do not always try to bring the logic to the limit by opening doors or pressing the EMERGENCY-Stop and expect that the lift will always restart after emergency halt without confirming of owner or company that the elevator is in a safe state to go back in use.
If that had a reset button if that happens it would fix the elevator and make it relevel at the nearest floor, or make the elevator reset when the doors open so when it closes that it will relevel
OMG! Seeing this makes me so sad! When I was visiting Stockholm last year I found this beautiful treasure by chance (I got an HD upload in my channel). I was so excited about the beauty of this lift. So small and it ran beautifully! Why didn't they just put in photocells? Everything would have been better than this stupid gate. And those generic beeping buttons... horrible!
+Kone Minispace (I cannot answer your comment. Check your settnings) Overseas? as Europe mainland? (Sweden in this case). well, the fewer the better. :p THeese elevators should ahve kept original as back in 2010 when I first encountered them...
what a fucking piece of shit. this is how generic companys make more money, on Newlift controllers (most common generic logic in germany) you can set the safety circuit time out. usually it is set to like 10 minutes, some generic companies near me set it to 1 second meaning people will get trapped and the lift breaks down on a simple safety break. when i saw that in the motor room i changed the timeout to a couple of mins higher.
When you open the gate, the safety circuit disconnects and the lift stops. That's why you have to close the gate before the lift will move.
If you open the gate while the lift is moving, it counts as an unauthorised opening and the lift stops or goes out of service, it went out of service in this case. It goes out of service to prevent unauthorised lift surfing.
An authorised opening is when the doors open while the lift is inactive at a floor.
The reason why the lift engineer asked you to close the gate was to connect the safety circuit and allow the lift to be manually moved using inspection mode, aka lift surfing.
Yes i'm so sorry about this. Seing this mod really destroys my soul.
Something that was supposed to be a nostalgia trip turned out to be a nightmare.
Unlucky
AMSLER IS A HUGE RIPOFF TO KONE
THIS ELEVATOR SHOULD BE MODERNISED BY MIDROC ELECTRO
Fuck generic companies, they destroy epic amazing lifts and replace it with boring stupid shit.
Kone lift
I think there are worse things that can happen.
I hate it when it happens. I would never get stuck in the elevators in Moscow, Russia. In London, UK. I got stuck twice for few seconds, the street elevator at North Greenwich Underground Station and the express elevator at an apartment building.
I'm speechless
5:11
Yes , this is the result if you do so.
They have warned you.
A wonder that the company did not charge you for that rescue.
When the elevator is modernized, often they have simpler logic.
Means when the elevator arrived close to the destination floor and starts levelling, its a small underprogramm that says
" start levelling for (lets say)5 seconds, open interlockcurve ( in german riegelkurve... a metall c shaped device ,motor or magnetic powered, that presses against the roll at the doorlock to release mechanical the door and interlockswitch), then activate magnet/motor to release the door, reset/ go back to next call and wait for doors closed...
But if this program gets interrupted due too early opening the inner door the logic blocks for safety. The lift needs to be closed and resetted manually, that the logic thinks the cabin is correct. Then just place any different call.
This happens when old elevators get renewed the easiest way, without adding a led tapemeasure( this tape or wheel from plastic with black lines or metall with holes with a infrared lightbarrierfork ( that the logic knows the absolute position of the cabin in the shaft), because the old shaft/ machine whatever may not support this new technique due space... or the owner just didnt want to pay a complete change of the system andvthey added just the necessary parts to meet code.
But however if you use unasked someones elevator, follow the attached rules and do not always try to bring the logic to the limit by opening doors or pressing the EMERGENCY-Stop and expect that the lift will always restart after emergency halt without confirming of owner or company that the elevator is in a safe state to go back in use.
Du kunde börjat med "Satana Perkele, Hissen har fastnat!" XD
If that had a reset button if that happens it would fix the elevator and make it relevel at the nearest floor, or make the elevator reset when the doors open so when it closes that it will relevel
Du glömde skrika ”HELVETE” 🤣
Shocking modernization!
HEMSKT! Gud vad sur jag blir, jag hade viljat sett hissen som orginal...
*_Band! This! Banding! Elevator! >:(_*
4:09 you got stuck
4:57 you pressed the alarm (the alarm was annoying)
OMG! Seeing this makes me so sad! When I was visiting Stockholm last year I found this beautiful treasure by chance (I got an HD upload in my channel). I was so excited about the beauty of this lift. So small and it ran beautifully! Why didn't they just put in photocells? Everything would have been better than this stupid gate. And those generic beeping buttons... horrible!
oh no, another wonderful old innerdoorless lift is now ruined : ,(
1:35 Oh wow the intro!
Epic music
Hello, can you tell me the Name of the music, that is playing at the beginning? cheers Toni
the sound of the 2011 microphone sounded like it fell in water twice
Do u guys not learn to trip the interlock?
idfk why do they lock the elevator doors anyway?
Why would they mod it? I liked it how it was!
I Love This Motor sound
Let me guess you tripped the safety beem
Nope, there isn't any.
Well... I think this wouldn't have happened with an S3 controller.
It should be modernised by kone ecodisc
Only the right way to modernise
5:03 the phone emergency phone
+Kone Minispace (I cannot answer your comment. Check your settnings)
Overseas? as Europe mainland? (Sweden in this case). well, the fewer the better. :p THeese elevators should ahve kept original as back in 2010 when I first encountered them...
du kunde med kolito dostana hissen far fastnat
If people keep doing that they have to mod it again if it becomes a annoyance
I think you meant UNFORTUNATELY, not "unfortenly".
Being stuck in an elevator is not fun, especially if you hate the elevator you are in.
4:57 emergency phone
Nice music
what a fucking piece of shit. this is how generic companys make more money, on Newlift controllers (most common generic logic in germany) you can set the safety circuit time out. usually it is set to like 10 minutes, some generic companies near me set it to 1 second meaning people will get trapped and the lift breaks down on a simple safety break. when i saw that in the motor room i changed the timeout to a couple of mins higher.
who took those fixtures overseas they belong in the UK not other countries shame they are spreading
That is so cheep
This modernisation is crap but this motor is awesome
I would never use this old shitty fking lift
Pathhetic beeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeep
Graphics was rubish
This Lift 👎🏻
THIS ELEVATOR IS A RIPOFF!
Very bad modernization.
Why you say fucking 👎
ㅓ means f***
吣冉扎
Kone elevator
That Stuck From What Building
Hiss
The mod is so disgusting and cheap.