One of my side plate came off while operating the boat, couldn't retrieve it. Ordered a pair from this website, I couldn't be any happier with the super fast shipping and the OEM part. Will definitely be my go to store.
12 years on and my XI5 is finally showing its age... I've put it through hell to its used at least 3 times a week... only issue I had was the original control board failing and me dropping the remote in water....I'd buy another and with minn kota prices through the roof its a no brainer
... Subscribed with the bell. Thanks. . 2016 Xi5, 36V, SW, Pinpoint. Has always worked great until the last few trips where the power to the prop was intermittent. Is there an internal switch that connects and disconnects when deploying and retracting? That seems to be where the issue is. . Last trip out, 4/9/23, prop would not turn all all. Everything else works as it should. Checked for 36V to the Battery Tender plug on the bow- Good. 36V Monster lithium battery a few months old. Thank you. . Jeff .
No bueno. I'm sure most have issues. Motherboard and pinpoint GPS would be annoying. I don't know if that remote floats. My luck it would break and go for a swim. Thank you for the info Rob.
I've taken mine in for service twice and both times they couldn't find anything wrong with it. The first time the problem was in the remote control, so now i keep at least two on the boat, with spare batteries also. The second time my motor would make one single beep when deployed but then not respond to any controls and my indicator lights were not lit. I replaced my plug in connector and 50amp breaker, everything working now. My power cord is baked by the sun very bad so i would recommend getting a cover for that if anybody hasn't already done it.
Unfortunately today I ran into that same controller issue and broke the tab off the end that upset me a little bit. I just bought this boat from a friend with the MotorGuide on it and was pretty excited another friend just bought a Minn kota for half again the money so it will be interesting to see performance and quality wise. The friend I bought the boat from just took off the latest motor guide out of disgust I guess almost every single one has had to be recalled due to brain issues after they tried to tell him it was out of warranty he basically threw that at the dealer they finally agreed to fix it it is going right up on Facebook marketplace so now I am kind of nervous
55 lb Xi5 with GPS is having issues since the dongle update and .SWUP software update. I can’t calibrate the gps. It’ll time out during calibration doing the tight circles with the outboard. It did accept a factory default gps calibration though. It also does the runaway speed routine when using cruise control. It also blasts RFI when using my Airmar transducer at the transom. Would a control board replacement be worthwhile to try? It’s an early build (2016) according to customer service. Thanks
Good video thanks. I have a question: my motor guide Xi3 will not turn left or right when I’m controlling it manually from the remote, but when I hit the anchor button, the steering works as it supposed to. I’m thinking just replace the control board?
My Xi5 is going on 8 years now. 1st year I had GPS problems, random loss of GPS and or anchor spot or heading. Took it in the shop they had it for two months, changed software "updated" it and said it was fixed. Got it back soon the same issues again. I took it apart and found that the wires going into the GPS modules where looking like they were pulled out a little. Motor guide send me new GPS modules, I rigged up a more robust cable clamp. i have no issues since. I cannot hear the alarms on the motor guide or the Lowrance F.F. that I use for controlling the Xi5. It looses anchor in a stiff wind and if sleeping or not paying attention I could drift into rocks fast. I can't hear the Anchor lost position alarm. I am building an Mic and Amp for the alarm to wake me up and let me know when I loose anchor position.
I got mine directly connected to a fully charged 12v battery. None of the indicator lights are on, but I did see the power one flickering a few times like it was trying to come on. Is this power cord related for motherboard related?
Yeah my biggest problem is the play in the foot pedal. I can press down almost an inch both ways and it never engages the steering. I wonder if it’s a loose cable. The Older styles with the metal foot pedal I’ve got so many of those fans they are the best trolling motor I’ve ever used
Yeah my biggest problem is the play in the foot pedal. I can press down almost an inch both ways and it never engages the steering. I wonder if it’s a loose cable. The Older styles with the metal foot pedal I’ve got so many of those fans they are the best trolling motor I’ve ever used
Hey I bought a new control board and curly cord from y’all and installed them but still no left or right steering……and recommendations? Also there is no sound while trying to steer it left or right
i was about to buy a motorguide xi5 but now i dont know . so if motorguide is bad who makes a great 24 volt 70 to 80 inch shaft with all the things that xi5 has? thanks for replying
I agree I got mines in 2017 and only replaced the controller once. it still run strong. I also keep in the garage when not In use and WD40 it after every wash. Salt water model. 😊
my xi5 is saying it is low battery, checked volts and amps on batteries(24 volt) and even tried recharging batteries. but chargers saying 100 % charged. what would you recommend I look at first. Both batteries are only 6 months old.
XI-5 unit- was not operating with the RC so I bought a new one. Now , when I operate it manually with RC, it shuts down after about 4 minutes. On the Lorrance unit, I have to re-set the auto pilot function each time this happens. What setting do I need to change on one or both units? Help please.
Could you tell me if I could just disable the GPS on my Xi5? Don't really use it. Both of my cables are cracking and it seems so expensive to replace for something I don't use.
I have the XI3 which just stopped working all together after it took off and rammed a bridge pylon. After watching this video on the Xi5, I think it's safe to say it could be every part. How in the world can THAT many important parts ALL be the MOST common to break or malfunction lol wtf.... These trolling motor ain't cheap in price but OBVIOUSLY are in manufacturing.
My XI5 will only turn right, Is this a control board issue? My coil cord is working ok but it is degraded from sun exposure. The thick "collar" part where it connects to the trolling is split.
So me and my friend have xi5 xi3 and yeas the remote is so sensitive and easy to just bend over somewhere and snap right into the water once it gets wet u will be lucky that it works and if does it will shut down a month later and they are expensive both of us already had to replace now the foot pedal u will soon break it to both of us replaced and mine I think I used to twice and it's already broke as I inside a plastic piece broke for left hand turn yes plastic these are the things I do had problems kind of keep me in business cause you know u love the thing ......do the small problem I have now is the transmission squeaks like a mother I pours oil everything on shaft still swueeerks one month it stopped squeeek ... Then recently it started squeeeeeekng again no mount of oil grease will help time to tear it open
What about the stow and deploy lock pins. Those flimsy little push caps will not stay on the pins, the arm that controls the locks (hooks, whatever you call them) will slip off the pin and you cannot deploy, or stow based on which position but it usually deploy because it happens when you step on the release foot control. Mine did this the second time out, and two of my buddies have had the same issue. Cannot find the parts to fix it!
Paul I agree1st trip out today 8-28-22 1sr time deployed the right hand side completely fell apart from the front tabs to the rear pins , these flimsily designed pins flat plate etc is very very weak and under designed Headed to bass prob tomorrow being today is Sunday Not happy at the moment dropping 3k for this 36 salt 105 and not happy at all , nothing against bass pro at the moment as long as they warranty with good customer service I’ve dropped 5 k this week with them Trolling motor , HDS9 & 3 optimas
@@donwalden6285 I ended up rebuilding mine in my own.... Motorguide said I'd have to send it in to them...I ordered mine online. Luckily you have a physical location. Please post back what they do for you.
I’m on my second gps module. Bought one to return it and get a new one that still doesn’t work. The motor will not get signal. The install is easy. Am I missing something to get it to squire signal? I know I have to do the calibration but I’m not even getting a signal on my indicator panel
I'm wondering how fixing the controller is a quick easy cheap fix we have Mickey mouse it by just drilling a hole through the top and adding a key ring but your bypassing the gasket so it's not completely sealed anymore no one sells just the back part of that controller that I have found I love having to Farmer fix the controller
Mines won’t make turns. Turns on goes forward and slows down stops everything else but once I hit my remote and tell it to turn or anchor it makes the noises just won’t turn. I don’t know what to do
Several of the issues he listed are no fault of MotorGuide I've heard they have several issues and Lawrence has pretty much bailed on them as they tried to blame Lawrence on those computer issues however when he was talking about parts breaking after being jammed or hit on something that is operator era not motor guides fault. That being said Minn kota and other systems do have breakaway mechanisms to allow the shaft to kick back if you hit something however the shaft on that MotorGuide is almost indestructible I've seen them bend at severe angle and come back
@@lauramurray6690 I agree. My xi5 hit a rock bank, bent in half (almost) and chunked my tracker deep v pro guide 175 backwards. A weld on the front of my boat broke and my trolling motor is still as good as new. My xi5 has also smacked into several boat docks when the wind was kickin' and still just like new. It's a beast. I'd buy another one. And lowrance did drop the ball. There is now a work around "code" to get my units to communicate. The glitch was supposed to be fixed and then lowrance released the Ghost and ditched motor guide the wolves.
They all have their issues. But the ones we see the least, would be the ones with the least amount of electronic / gps features built into them. I would base your decision on what motor fits your style of fishing and boat setup the best.
great video. my xi5 is not working the gps. not even the indicator light is lit. Is the solution to replace the GPS system? or is there anything i can do?
Good morning, I'm in Brazil, I have a Motorguide xi5, my remote control when in use, if I'm turning it to the left or right side, when I take my finger off the remote control the motor head doesn't stop turning, do you have any idea What can it be?
It's hard to accurately troubleshoot without having the motor in front of me. But, I would start by testing it with a Foot Pedal. If the steering doesn't stick with the Pedal, My guess would be a bad remote.
Yep mine broke but just roughed up surface and epoxied a key ring to back. If you find the right size ring it will fit fine and then hook lanyard to the ring.
The cables rotted after a few years and fell apart completely. What's worse is you cannot purchase the GPS cable alone, you have to buy the whole module.
Geez, I am glad that I watched this but really disappointed because I like Garmin fish finders. So I am torn between Hummingbird with Minn Kota or Garmin with Motorguide. I want compatibility between fish finder and trolling motor.
YES! The Ramp Deckettes are pure Sh%# on the Xi5. I have replaced mine twice in 3 years. Cheap plastic without metal reinforcement in the high stress areas. AND they arent cheap to replace!
Ok when u first get the x you will be thinking what a piece of dodo but once you remember the characteristics of how it works you can be a step ahead of it and make it sing I can be running up to shore to get snagg out and already have it heading locked and and boat going back the direction u want it and get the snag out and grab a sandwich you have to learn it's programming first before u give up on it then u will really like it and I have a jet boat lowe so I want to keep it light the xi3 or 5 you can pick up with one hand the minn kota two arms struggling just to get up to mount super heavy
Should have been made much better for the price we paid for it . Remote cheap hook broke and shaking shaft and most the time board dosen't responds to connected controls.
So if u get a new remote and you will break out the permatex and screws and do a little strengthening to it modify it cause they know dam well with all them engineering and brains one little slice of plastic is going to break the first two weeks I own
I haven't had any issues with my xi5. I've had it for a few years now. Unfortunately, lowrance now has their own motor and therefore, have quit giving updates to the Motorguide products.
I’ve never came across an issue with my Xi5 ever. But, I also take care of my stuff and do routine maintenance on it. And all my cables have cable covers on them
Turned mine into a manmade reef. Problems from day 1. Called customer service and they kept hanging up. WILL NEVER EVER BUY ANYTHING MOTOR GUIDE AGAIN...
![Sean Rii, Karyon, Sharzkii - Taungule [My Love] (Official Music Video)](http://i.ytimg.com/vi/eJoMuypbSzQ/mqdefault.jpg)
One of my side plate came off while operating the boat, couldn't retrieve it. Ordered a pair from this website, I couldn't be any happier with the super fast shipping and the OEM part. Will definitely be my go to store.
12 years on and my XI5 is finally showing its age... I've put it through hell to its used at least 3 times a week... only issue I had was the original control board failing and me dropping the remote in water....I'd buy another and with minn kota prices through the roof its a no brainer
The trolling motor “head” has no seals. This allows water to eventually find its way to the “lower unit” and wreak havoc. Good video!
I know I’m a year late but Motorguude, even in the late 80’s/90’s leaked bad. I’m here just to see if they’ve improved. Guess not
... Subscribed with the bell. Thanks.
.
2016 Xi5, 36V, SW, Pinpoint. Has always worked great until the last few trips where the power to the prop was intermittent.
Is there an internal switch that connects and disconnects when deploying and retracting? That seems to be where the issue is.
.
Last trip out, 4/9/23, prop would not turn all all. Everything else works as it should.
Checked for 36V to the Battery Tender plug on the bow- Good.
36V Monster lithium battery a few months old.
Thank you.
. Jeff .
No bueno. I'm sure most have issues. Motherboard and pinpoint GPS would be annoying. I don't know if that remote floats. My luck it would break and go for a swim. Thank you for the info Rob.
I've taken mine in for service twice and both times they couldn't find anything wrong with it. The first time the problem was in the remote control, so now i keep at least two on the boat, with spare batteries also. The second time my motor would make one single beep when deployed but then not respond to any controls and my indicator lights were not lit. I replaced my plug in connector and 50amp breaker, everything working now. My power cord is baked by the sun very bad so i would recommend getting a cover for that if anybody hasn't already done it.
Unfortunately today I ran into that same controller issue and broke the tab off the end that upset me a little bit. I just bought this boat from a friend with the MotorGuide on it and was pretty excited another friend just bought a Minn kota for half again the money so it will be interesting to see performance and quality wise. The friend I bought the boat from just took off the latest motor guide out of disgust I guess almost every single one has had to be recalled due to brain issues after they tried to tell him it was out of warranty he basically threw that at the dealer they finally agreed to fix it it is going right up on Facebook marketplace so now I am kind of nervous
55 lb Xi5 with GPS is having issues since the dongle update and .SWUP software update. I can’t calibrate the gps. It’ll time out during calibration doing the tight circles with the outboard. It did accept a factory default gps calibration though. It also does the runaway speed routine when using cruise control. It also blasts RFI when using my Airmar transducer at the transom.
Would a control board replacement be worthwhile to try? It’s an early build (2016) according to customer service.
Thanks
Exactly what I needed. I ordered part yesterday but didn’t get a confirmation email. How can I verify?
Lost 2 seasons of fishing dealing with motorguide
Good video thanks. I have a question: my motor guide Xi3 will not turn left or right when I’m controlling it manually from the remote, but when I hit the anchor button, the steering works as it supposed to. I’m thinking just replace the control board?
My Xi5 is going on 8 years now. 1st year I had GPS problems, random loss of GPS and or anchor spot or heading. Took it in the shop they had it for two months, changed software "updated" it and said it was fixed. Got it back soon the same issues again. I took it apart and found that the wires going into the GPS modules where looking like they were pulled out a little. Motor guide send me new GPS modules, I rigged up a more robust cable clamp. i have no issues since. I cannot hear the alarms on the motor guide or the Lowrance F.F. that I use for controlling the Xi5. It looses anchor in a stiff wind and if sleeping or not paying attention I could drift into rocks fast. I can't hear the Anchor lost position alarm. I am building an Mic and Amp for the alarm to wake me up and let me know when I loose anchor position.
I got mine directly connected to a fully charged 12v battery. None of the indicator lights are on, but I did see the power one flickering a few times like it was trying to come on. Is this power cord related for motherboard related?
Yeah my biggest problem is the play in the foot pedal. I can press down almost an inch both ways and it never engages the steering. I wonder if it’s a loose cable.
The Older styles with the metal foot pedal I’ve got so many of those fans they are the best trolling motor I’ve ever used
I'm having issues with my Xi5, getting a "no autopilot computer" alarm on my HDS Live 12, what might this issue be GPS module or control board
Can you do a video on repairing the xi foot pedal steering magnet(s)?
WELL DONE!!!
Yeah my biggest problem is the play in the foot pedal. I can press down almost an inch both ways and it never engages the steering. I wonder if it’s a loose cable.
The Older styles with the metal foot pedal I’ve got so many of those fans they are the best trolling motor I’ve ever used
Hey I bought a new control board and curly cord from y’all and installed them but still no left or right steering……and recommendations? Also there is no sound while trying to steer it left or right
Your videos are great! How about one on the Ulterra? Thanks
Thank you! We’ll have a few coming out on the Ulterra soon.
Which one has the least amount of problems in general?
Motor guide or Minn kota ?
I’m looking to put a new trolling motor on my boat.
i was about to buy a motorguide xi5 but now i dont know . so if motorguide is bad who makes a great 24 volt 70 to 80 inch shaft with all the things that xi5 has? thanks for replying
I’ve spent hundreds of hours w xi5 and it’s never once messed up.
Pure luck, that's all.
I agree I got mines in 2017 and only replaced the controller once. it still run strong. I also keep in the garage when not In use and WD40 it after every wash. Salt water model. 😊
it's call Maintenance and TLC.😊
bought mine when the first came out late 2012 still going but showing its age....for the price they are great motors.
Good for y my gps went out 2nd year on my third remote in 4 years column caps had to replace 3rd year
my xi5 is saying it is low battery, checked volts and amps on batteries(24 volt) and even tried recharging batteries. but chargers saying 100 % charged. what would you recommend I look at first. Both batteries are only 6 months old.
XI-5 unit- was not operating with the RC so I bought a new one. Now , when I operate it manually with RC, it shuts down after about 4 minutes. On the Lorrance unit, I have to re-set the auto pilot function each time this happens. What setting do I need to change on one or both units? Help please.
Is it possible to ship a controll board to sweden
How do you make the footpedal usable
Could you tell me if I could just disable the GPS on my Xi5? Don't really use it. Both of my cables are cracking and it seems so expensive to replace for something I don't use.
My motor will not go full throttle, brand new control board... what would could be causing this issue?
All the indicator lights on my xi5 quit working. The trolling motor still works and beeps but no lights. Is there a part for that? Thanks!
I have the XI3 which just stopped working all together after it took off and rammed a bridge pylon. After watching this video on the Xi5, I think it's safe to say it could be every part. How in the world can THAT many important parts ALL be the MOST common to break or malfunction lol wtf.... These trolling motor ain't cheap in price but OBVIOUSLY are in manufacturing.
My XI5 will only turn right, Is this a control board issue? My coil cord is working ok but it is degraded from sun exposure. The thick "collar" part where it connects to the trolling is split.
So me and my friend have xi5 xi3 and yeas the remote is so sensitive and easy to just bend over somewhere and snap right into the water once it gets wet u will be lucky that it works and if does it will shut down a month later and they are expensive both of us already had to replace now the foot pedal u will soon break it to both of us replaced and mine I think I used to twice and it's already broke as I inside a plastic piece broke for left hand turn yes plastic these are the things I do had problems kind of keep me in business cause you know u love the thing ......do the small problem I have now is the transmission squeaks like a mother I pours oil everything on shaft still swueeerks one month it stopped squeeek ... Then recently it started squeeeeeekng again no mount of oil grease will help time to tear it open
I did break my remote. I gorilla glued it back together and haven't had an issue since.
What about the stow and deploy lock pins. Those flimsy little push caps will not stay on the pins, the arm that controls the locks (hooks, whatever you call them) will slip off the pin and you cannot deploy, or stow based on which position but it usually deploy because it happens when you step on the release foot control. Mine did this the second time out, and two of my buddies have had the same issue. Cannot find the parts to fix it!
Paul I agree1st trip out today 8-28-22 1sr time deployed the right hand side completely fell apart from the front tabs to the rear pins , these flimsily designed pins flat plate etc is very very weak and under designed
Headed to bass prob tomorrow being today is Sunday
Not happy at the moment dropping 3k for this 36 salt 105 and not happy at all , nothing against bass pro at the moment as long as they warranty with good customer service
I’ve dropped 5 k this week with them Trolling motor , HDS9 & 3 optimas
@@donwalden6285 I ended up rebuilding mine in my own.... Motorguide said I'd have to send it in to them...I ordered mine online. Luckily you have a physical location. Please post back what they do for you.
I’m on my second gps module. Bought one to return it and get a new one that still doesn’t work. The motor will not get signal. The install is easy. Am I missing something to get it to squire signal? I know I have to do the calibration but I’m not even getting a signal on my indicator panel
Same issue. I added the gps upgrade to my xi3. I’m about to scrap it
I'm wondering how fixing the controller is a quick easy cheap fix we have Mickey mouse it by just drilling a hole through the top and adding a key ring but your bypassing the gasket so it's not completely sealed anymore no one sells just the back part of that controller that I have found I love having to Farmer fix the controller
Mines won’t make turns. Turns on goes forward and slows down stops everything else but once I hit my remote and tell it to turn or anchor it makes the noises just won’t turn. I don’t know what to do
Same here and mine is brand spanking new!?
How much coil cord?
nice video. are these motors still recommandable ? or do they get broken all the time? or is the minn kota better?
I've had my xi5 for several years now and I haven't had any issues. I've beat the hell out of it a few times (on accident).
Several of the issues he listed are no fault of MotorGuide I've heard they have several issues and Lawrence has pretty much bailed on them as they tried to blame Lawrence on those computer issues however when he was talking about parts breaking after being jammed or hit on something that is operator era not motor guides fault. That being said Minn kota and other systems do have breakaway mechanisms to allow the shaft to kick back if you hit something however the shaft on that MotorGuide is almost indestructible I've seen them bend at severe angle and come back
@@lauramurray6690 I agree. My xi5 hit a rock bank, bent in half (almost) and chunked my tracker deep v pro guide 175 backwards. A weld on the front of my boat broke and my trolling motor is still as good as new. My xi5 has also smacked into several boat docks when the wind was kickin' and still just like new. It's a beast. I'd buy another one. And lowrance did drop the ball. There is now a work around "code" to get my units to communicate. The glitch was supposed to be fixed and then lowrance released the Ghost and ditched motor guide the wolves.
I was looking at a used Xi5 for $900 but now I'm not so sure I want it!!
how to test gps module
Crazy question here...what TM do you see the least of? What do you recommend to buy? Minnkota or Motorguide? I'm in the market for a 24v 70-80lb TM.
They all have their issues.
But the ones we see the least, would be the ones with the least amount of electronic / gps features built into them.
I would base your decision on what motor fits your style of fishing and boat setup the best.
@@trollingmotorparts Thanks for replying.
great video. my xi5 is not working the gps. not even the indicator light is lit. Is the solution to replace the GPS system? or is there anything i can do?
@@trollingmotorparts I wouldn't be without my xi5 linked to my Lowrance, for spot lock, trolling, heading lock and automatic pilot.
sometimes my motor won't power up when I deploy it. 24v 80 pound.
Good morning, I'm in Brazil, I have a Motorguide xi5, my remote control when in use, if I'm turning it to the left or right side, when I take my finger off the remote control the motor head doesn't stop turning, do you have any idea What can it be?
It's hard to accurately troubleshoot without having the motor in front of me.
But, I would start by testing it with a Foot Pedal. If the steering doesn't stick with the Pedal, My guess would be a bad remote.
My coil cord is showing signs of age and was repairing it with liquid electrical tape and shrink tape… now I know where to go get a new one. That
#4 replacement mother board didnt work either
what trolling motor would you outfit on your own personal freshwater craft?
Please could you give an opinion on my question
#3 issue, tab on remote breaks easily
Yep mine broke but just roughed up surface and epoxied a key ring to back. If you find the right size ring it will fit fine and then hook lanyard to the ring.
#2 issue, 1yr messing with "customer service" & "certified service centers" they don't work either
The cables rotted after a few years and fell apart completely. What's worse is you cannot purchase the GPS cable alone, you have to buy the whole module.
Geez, I am glad that I watched this but really disappointed because I like Garmin fish finders. So I am torn between Hummingbird with Minn Kota or Garmin with Motorguide. I want compatibility between fish finder and trolling motor.
YES! The Ramp Deckettes are pure Sh%# on the Xi5. I have replaced mine twice in 3 years. Cheap plastic without metal reinforcement in the high stress areas. AND they arent cheap to replace!
Ok when u first get the x you will be thinking what a piece of dodo but once you remember the characteristics of how it works you can be a step ahead of it and make it sing I can be running up to shore to get snagg out and already have it heading locked and and boat going back the direction u want it and get the snag out and grab a sandwich you have to learn it's programming first before u give up on it then u will really like it and I have a jet boat lowe so I want to keep it light the xi3 or 5 you can pick up with one hand the minn kota two arms struggling just to get up to mount super heavy
Should have been made much better for the price we paid for it .
Remote cheap hook broke and shaking shaft and most the time board dosen't responds to connected controls.
The biggest problem is warranty, they won’t supply parts for warranty, if it misses up you’re screwed
So if u get a new remote and you will break out the permatex and screws and do a little strengthening to it modify it cause they know dam well with all them engineering and brains one little slice of plastic is going to break the first two weeks I own
They finally replaced motor, will find out soon if it works. Low expectations
HELLO, can you make this vidéo on FRENCH language pleeeeeease !!
#1 issue, they don't work as promised!
For starters, don't buy this cheap Motorguide crap and avoid at all cost!
Best tip I can give you.
I haven't had any issues with my xi5. I've had it for a few years now. Unfortunately, lowrance now has their own motor and therefore, have quit giving updates to the Motorguide products.
I’ve never came across an issue with my Xi5 ever. But, I also take care of my stuff and do routine maintenance on it. And all my cables have cable covers on them
Why don't they make a manually deploy and manually steer 24 volt 62" shaft....
Spot lock is OVER RATED and so is motor diven stow and deploy......
Turned mine into a manmade reef. Problems from day 1. Called customer service and they kept hanging up. WILL NEVER EVER BUY ANYTHING MOTOR GUIDE AGAIN...
Dont buy this motor... broke down after 2 years of light use