Street Light Auto and Manual Connection / Street light Wiring / Explained with Circuit Diagram

In this video, I have explained the street light wiring connection. Here this circuit can be operated manually and automatically. The electric timer is used for automatic connection.
Thanks for watching this video.
If you have any questions, please comment below the video. I will answer your questions.
PLEASE SUBSCRIBE THIS CHANNEL FOR MORE VIDEOS.
www.youtube.co....
💻Connect with SL Engineering Academy
🌐Facebook 📲 / sl-engineering​. .
More video
Star-Delta Starter Complete Wiring for 3 Phase Motor / Star-Delta Control Connection / Explained
• Star-Delta Starter Com...
Solar Panel Connection with Inverter for Home / Off Grid Solar Panel System / Explained Step by Step
• Solar Panel Connection...
Complete Electrical House Wiring / Single Phase Full House Wiring Diagram /- Part 1
• Complete Electrical Ho... ​
Complete Electrical House Wiring - Part 2
• Complete Electrical Ho... ​
Float Switch Connection with Auto & Manual Selector Switch for Single Phase Water Pump
• Float Switch Connectio... ​
Complete House Wiring with Inverter Connection/ How to Select Inverter & Battery Capacity/ Explained
• Complete House Wiring ... ​
1 Gang & 2 Gang, 1 Way Switch Connection / How to Wire One Gang & Two Gang Light Switch / Explained
• 1 Gang & 2 Gang, 1 Way... ​
3 Gang & 4 Gang Switch Connection / How to Wire Three Gang & Four Gang Light Switches / Explained
• 3 Gang & 4 Gang Switch... ​

[@alemtarekegn7747]

Very thanks you helped me much❤❤❤

[@john-kneebee2143]

Bravo !! Well done !! Please consider the other side of the coin too, sizing of the neutral, a three phase example vs single phase, and the fact that this must be from a "Y" service due to the neutral, as well as not hospital grade, the isolated ground, equipment grounding etc..... basics are the best beginning.....very clear crisp and clean !! Nice.

[@ElectroProjects]

Great video. Good presentation.

[@slengineeringacademy2234]

Thanks.❤👍

[@younus594]

ধন্যবাদ আপনাকে

[@sawhtetlinthan8008]

Dear Sir.Thank so much for your knowledge sharing program.Have a great good luck..

[@slengineeringacademy2234]

Thanks for watching ❤👍

[@sawhtetlinthan8008]

Dear Sir,Could you share me your Social media address such as Whatsapp phone number or facebook acc?I am very repect to you so I want to be a friend with you.Thanks Sir..

[@emmanuelnelson8941]

very nice, clear and easy to understand this!

[@slengineeringacademy2234]

Thanks for watching ❤👍

[@vijaykaviya9894]

Thankyou Bro😊

[@abieladanga3111]

Interesting

[@chdsusanthachandrakumara9543]

Good

[@slengineeringacademy2234]

Thanks ❤👍

[@nadr2020]

Thank you 👍👍

[@slengineeringacademy2234]

Thanks for watching❤👍

[@ivantash5033]

Thanks alot

[@slengineeringacademy2234]

❤👍❤👍

[@s.s.broesel6576]

Dieser Kanal ist Top-OK.
Ich muss aber anmerken: die Schaltung am Analog-Timer ist theoretisch falsch. Immer wenn man auf Manual oder auf AUS schaltet, bleibt der Timer(Uhr) auch(immer) stehen.
Ohne neue Zeiteinstellung (ohne Zeitverlust) am Timer(Uhr):
Analog-Timer, Anschluss 4 (L) direkt an Single Pole MCB, oberer Anschluss.
This Channel is Top-OK.
But I have to say: the circuit on the analog timer is theoretically wrong. Whenever you switch to manual, the timer also stops.
Without a new time setting (without loss of Time) on the Analog Timer:
Analog timer, connection 4 (L) directly to Single Pole MCB, upper connection.

[@rodri6709]

SL Enginnening Acedemy

[@mohamedmarhoon3338]

Must be connecting earth cables

[@knowhowspirit8589]

good...
home load/bill malom karain..
channel "knowhow Spirit".

[@peter_manu]

👏👏👏

[@slengineeringacademy2234]

👍❤

[@ZakirHossain-uj2ip]

Mistake connection timer auto connection,because timee power connetion.

[@Bollywood1155]

Connection wala video kaise bnate ho bhai

[@ahmedgassan8836]

whats the maximum distance you can give it

[@vipwhatsup1932]

If any one phase off... What happened?

[@Knuck3ls1]

Seeing as how this is wired, hopefully someone will correct me if I'm wrong, your question would depend on which phase. If it lost "A" phase, or L1, none of the controls would function. If it lost "B" or "C" phase, those lights wouldn't turn on, but contactor should still function as normal.

[@MuhammadAhmad-pw4qx]

Sir what if there are more than 6 lights.

[@WAPCOSLimitedMEPZSEZProjectOff]

how to select mcb rating for this panel

[@mahsennassor467]

It depends on time of voltage power rating of your components

[@mahsennassor467]

I mean type

[@user-ss8yn3lc5c]

Sir please explain in Hindi language audio

[@SachinVerma995511]

Hello sir, how can i connect you

[@tariqkhan-dp4fu]

can you tel me sopter name i need this supter

[@julieanndaitol7227]

sposibol babae naepasok ung isipan sa grond ng gadget dahilan ng deenasahan sa naliligo habang gomagamit ng gadget...

[@user-sey4t5]

Please Video 1pas

[@plirofor1032]

dear sir, is there any free software to draw easily
like this electrical diagrams?

[@vishak8428]

Good

[@slengineeringacademy2234]

❤👍❤