I appreciate your videos so much. I have always depended on my dad to do my repairs and in this last year he has had many health problems. My roof has been leaking and I was hesitant to try to fix myself but after watching your instruction I am going to give it a try and I hope to be successful, it would make him proud for sure. Question? Have you ever fell off a roof?
Milwaukee should most certainly sponsor you! Appreciate all of your incredibly useful and priceless help! Your years of experience are superb, Hands down!! Greatly greatly do appreciates you sir!!
thanks for taking the trouble for making this video. Turbo poly is a polyurethane seal and you said it is better if it is painted over with Silver coat. I have looked at many brands of polyurethane seals (we do not have Bergstromm brands here) and the one thing they have in common is that they declare it is UV resistant. Painting not required on any of them. Have you ever found Turbo poly seal to fail in the sun? Personally, if I had it I would dilute it with water to make it slightly runnier(like the super silicon). On the other hand I am a fan of water soluble bitumen. It cannot be painted and it is not UV resistant, but what I found is that if you use the polyester mesh and on the second coat you sprinkle and embed white clean coarse sand, it lasts much longer and once cured, it can be painted
I am drinking coffee and feeling some hope. I was quoted over $40k for my roof to get replaced before the lockdowns.... no one wants to repair, just replace. My son is old enough to get up on the roof now though so we'll be investing in one of these angle drivers and the sealer. Thank you for your advice.
I wish you could see my leaky roof 3 x 3 foot area you would probably figure it out really fast but it's a totally unique situation and impossible to explain. Such a small area and I cannot fathom how it is still leaking as much as I've done and spent. Thanks for sharing I'm going to figure it out hopefully eventually.
very nice explanation, of a very nice fix. but the original builder put the screws on the low part of the metal. what is your opinion of puting the screws on the small high part of the metal roof ? Water is running on the low part where the screw is.
Great video. I'm in South Africa and cannot find the products you use, however I will get something equivalent. I will however use your methods that seems to work well. Thanks.👍
Excellent question. There was a little rust here and there but nothing to be concerned about. It was going to take a much bigger effort to wire brush the underside as well. If you have the means to do so, then you are doing a 100% better job than I did. I think it will mean to undo more screws further up the panel so you could lift up the panel higher. I believe that is doable and should really be addressed.
This is how the metal sheets were fastened. There is a sealant between the 2 overlapping panels at the sea,. So the overlapping panel has to to be tight at the seam to make the sealant seal. If there were no screws, then the top panel would heave up and cause a gap between the seams. Hmm, I don't know if my explanation made sense. Maybe someone could comment and do a better job.
I have the exact scenario as your demonstration. Especially the part about accessing underneath the overlapped seam. BUT...there is no wood purlins or anything to drill it to. In the past, perhaps even originally, they used rivets to join these overlaps. Then at some point they used screws. So, my question is, will these methods work if I cannot screw into wood underneath?
Looks like a good product for sealing roofs but the practice of running fleece and sealer across the overlap has the effect of damming moisture. At the side laps of the panels a little bit of water gets in via 1 condensation 2 rain splash 3 water level in the valley 4 leaf debris or 5 snow melt 6 capillary action. Moisture that gets into the side gap at the point just above the sealant band will travel downslope inside the side lap joint. The moisture is dammed by the fleece and sealant at the cross joint so it builds up and stays there to create rust problems into the future. The broader the width of sealant up and down the roof the more likely it is for the moisture to build up to a higher level between the sheeting layers. (even enough to go to the top of ridges) It is really important to have a reasonable lengthwise overlap of the sheets and to have the lower edge slightly open for drainage - not fleeced and sealed over the horizontal joints.
Your right as the Landlord of my rental factory put bitumen over the lap joint and when water got in due to cracking the whole length of the roof became wet as the water could not escape. Now I have extensive rust and it impossible to locate the areas that are the problem as the water travels along before it starts to drip through. I had to break the whole seam open to allow the water to escape.
@andysurfer318 I would not seal seams. Repair top and bottom overlapping sheets independently. Also try not to have sheeting installed as colums of overlapping sheets. Better installed as row by row. This reduces capillary action inside 4 layers of sheeting at junctions.
Sir you seem very knowledgable. I hired a handyman who did a bad install on a 12x20 Veikous car port. It leaks from all 3 seams inside, lapping is uphill and water leaks thorough. He also failed to remove the plastic protection for shipment on top of roof. 9 hours for me to remove except plastic under lapped metal and screws. What can i do to micky rig it to leak less on inside? Chaulk or turbo seal and tape. I'm 65 retired and trying to stretch dollar I spoke to a contractor who can do rebuild way $$$!
Yikes.. Did a roof inspection and found a rust hole starting on the metal ridge ( same type of roof in video ). Turbo seal dose not ship to five O?? And some small flash rust stating also in small spots. Not big but will clean and spot paint.Roof is very flat with just a small incline so water runs off. Like your feedback. Off to the hardware store for some flashing tape to temp seal the hole untill sunny day.
Letting that dry overnight just makes the gap larger between the two pieces of metal that overlaps. It's not going to dry flat . I'd squirt clear silicone and smash to two panels together while it's wet then do your turbo poly seal over it.
One question I have a roof panel that was cut to short so the water is not getting into the gutter I do have a small off cut could this be used to extend the sheet?
I've got the same issue between the seams and screws along the bottom row of roof panels on galvanised IBR just above the bull nose. Will these methods not trap the water between the overlapping panels above the treated area?
I need help i'm a first time homeowner and I had a new roof put on my house and the roofer ruined 3 rooms of mine with leaks and I just want my roof to stop leaking do you do north carolina
Hey I’m in texas and have a flat metal roof with almost zero pitch. I have seams where they overlapped and almost left 3 inches of overlap. What do you advise and how much would you charge to come to texas and fix my roof ?!
I'm afraid to walk on my Mobile home roof like you do. First to clean it then to seal the screws heads and joints of a 13 year old roof Aluminum roof. Do u think it's ok to low crawl around up there?
Hey Frank Start from the edge and slowly shuffle your way to the center and feel if the roof will support your weight. The other thing you can do is to place 2 x 3 ft x 1/2" plywood that will disperse your weight when standing on them doing the job.
Hello Doctor, very interesting to watch your video. Please tell me where can I purchase that Turbo Poly Seal and will that tuff can stand UV rays with the heat in Texas ? Many Thank
If you just want to protect your metal roof against corrosion and rust, I recommend Aluminum Asphalt paint by Karnak. But don't paint the roof if you have leaks. First fix the leaks then you can apply a coating. It is very important to find all the leaks and wait a couple of months to be absolutely sure there are no leaks before you attempt any coating.
@@FlatRoofDoctor what is the cloth like material YOU’RE using? Can you use it on nail holes on shingles? You know stuff Doc! Thank you for sharing your knowledge with the world🥇🥇🏆🏆❣️❣️
Oh boy, I had a brand new metal roof installed 3 years ago and so far it’s leaking in 7 different places. It’s a huge roof,50 square and I am so disappointed because it was so expensive and of course the roofers left state so now I’m stuck. They didn’t sheet it, instead used a silver bubble liner. My inexperience cost me big time. It’s an old slated roof and from the inside I see where they missed the slats and screws are showing right through the metal and wrap. Someone told me to caulk every single screw in the roof which would be a huge project. I’d absolutely do this if it’ll work but is this going to be a waste of a lot of time and money? Any suggestions from a true professional?
Idea is to buy it in one sheet and the metal seams should of been sealed if your using 2 sheets. This is just putting a bandaid on the problem. The trailer roof you did would of been easier to lay metal down and it would of lasted a lifetime. I beat shingle prices with metal and that's why I'm a 5 star rated company. I warranty my work too.
No knee pads,no gloves,no fall protection? Not even a dust mask when grinding !!. This ol guy needs learn few things! Look all the sht on his hands at 11:00 min in.. 😂
I don't see how you're still in business buying Turbo Poly Seal. It's $200 for one gallon, that's insane. Black jack eterna-kote is $300 for five gallons and way better.
I’m sorry, I don’t mean to be rude, but what a mess. There are far cleaner and more secure ways to repair a flat roof. At least use some masking tape for a more attractive finish!
I do not understand why you are always showing those kinds of metal roofs, and the leaks there can be repaired by anybody with little brain. I know you are an expert but such repairs are not a big deal....Nowadays nobody installs such metal on their roof except for owners of commercial buildings, farms or sheds!!! If you are that much skilled, show me how to repair my shingle metal roof! and then I will pray for your business and success !!!! It is leaking almost from everywhere especially where the roof is connected to the exterior walls, my exterior walls show all those leakage lines.... disgusting ......Helppppp
Hi Bill There are not many people that have "shingle Metal Roofs". I am sorry that I have disappointed you with my videos. I am showing repairs that I run across in my business from day to day. You are expecting me to go out of my way to find something exceptionally just to help you. I don't have those type of clients, sorry
If you do not use an oxygen disipating chemical seal first. It will rust under anything put over old rusty areas. Believe me I'm in the auto body industry and I know what I'm talking about.
That's one of his past job failures, were he used duper silicon sealer to seal the whole roof, it didn't hold up, now he's back to fix the problem areas failing. What a con artist this guy is.
Thank you I have watched your programs for 12 years now. Thank you for your advice again
I appreciate your videos so much. I have always depended on my dad to do my repairs and in this last year he has had many health problems. My roof has been leaking and I was hesitant to try to fix myself but after watching your instruction I am going to give it a try and I hope to be successful, it would make him proud for sure. Question? Have you ever fell off a roof?
Milwaukee should most certainly sponsor you! Appreciate all of your incredibly useful and priceless help! Your years of experience are superb, Hands down!! Greatly greatly do appreciates you sir!!
thanks for taking the trouble for making this video. Turbo poly is a polyurethane seal and you said it is better if it is painted over with Silver coat. I have looked at many brands of polyurethane seals (we do not have Bergstromm brands here) and the one thing they have in common is that they declare it is UV resistant. Painting not required on any of them. Have you ever found Turbo poly seal to fail in the sun? Personally, if I had it I would dilute it with water to make it slightly runnier(like the super silicon). On the other hand I am a fan of water soluble bitumen. It cannot be painted and it is not UV resistant, but what I found is that if you use the polyester mesh and on the second coat you sprinkle and embed white clean coarse sand, it lasts much longer and once cured, it can be painted
I am drinking coffee and feeling some hope. I was quoted over $40k for my roof to get replaced before the lockdowns.... no one wants to repair, just replace. My son is old enough to get up on the roof now though so we'll be investing in one of these angle drivers and the sealer. Thank you for your advice.
Thank You Everybody for All that you are doing for our Planet Earth.. Peace Shalom Salam Namaste 🙏🏻 😊 🌈 ✌ ☮ ❤ 🕊
Very instructed video sweetheart 👍🏼
Thank you sweetheart
Excelente material y Gran trabajo
You know someone has mastered their profession when they get done,and their clothes/ hands are still clean.
Can i apply/put any kind of paint on top of turbo poly seal.
I have one of these roofs here in Japan and it leaks when it rains alots. This is a great help so thanks alots for your video.
I wish you could see my leaky roof 3 x 3 foot area you would probably figure it out really fast but it's a totally unique situation and impossible to explain. Such a small area and I cannot fathom how it is still leaking as much as I've done and spent. Thanks for sharing I'm going to figure it out hopefully eventually.
very nice explanation, of a very nice fix. but the original builder put the screws on the low part of the metal. what is your opinion of puting the screws on the small high part of the metal roof ? Water is running on the low part where the screw is.
Your right so put the screws on the high ridges of the metal...👍
Great video. I'm in South Africa and cannot find the products you use, however I will get something equivalent. I will however use your methods that seems to work well. Thanks.👍
Beast❣️😘 This guy is no youngster🥺🥺😘 RESPECT!
Be careful up there on those roofs😲🙏🙏
thanks
Great job, thanks for the video
Was there rust or did you wirebrush the under side of the upper panels? Why not put butyl sealant on the under side of the patches?
Excellent question. There was a little rust here and there but nothing to be concerned about. It was going to take a much bigger effort to wire brush the underside as well. If you have the means to do so, then you are doing a 100% better job than I did. I think it will mean to undo more screws further up the panel so you could lift up the panel higher. I believe that is doable and should really be addressed.
Im looking for advice on making my own metal patches from recycled tin cans.
Great video! Thanks for sharing your knowledge, much appreciated 👍🏻
I am glad you enjoyed it
Thanks for the comment, much appreciated
Nice job,thanks for sharing..it saves me lots of time
Why do the screws go into the valleys and not the ridges? Surely that causes water to accumulate around the screw?
This is how the metal sheets were fastened. There is a sealant between the 2 overlapping panels at the sea,. So the overlapping panel has to to be tight at the seam to make the sealant seal. If there were no screws, then the top panel would heave up and cause a gap between the seams.
Hmm, I don't know if my explanation made sense. Maybe someone could comment and do a better job.
en daar maak die program klaar met ' hier kom die bokke!'. dankie vir jou deeglike verduidelikings en goeie werk, Naas.
dis a plesier man. Ek raak ook nou out vir die dinge
I have the exact scenario as your demonstration. Especially the part about accessing underneath the overlapped seam. BUT...there is no wood purlins or anything to drill it to. In the past, perhaps even originally, they used rivets to join these overlaps. Then at some point they used screws. So, my question is, will these methods work if I cannot screw into wood underneath?
Looks like a good product for sealing roofs but the practice of running fleece and sealer across the overlap has the effect of damming moisture. At the side laps of the panels
a little bit of water gets in via 1 condensation 2 rain splash 3 water level in the valley 4 leaf debris or 5 snow melt 6 capillary action. Moisture that gets into the side gap at the point just above the sealant band will travel downslope inside the side lap joint. The moisture is dammed by the fleece and sealant at the cross joint so it builds up and stays there to create rust problems into the future.
The broader the width of sealant up and down the roof the more likely it is for the moisture to build up to a higher level between the sheeting layers. (even enough to go to the top of ridges)
It is really important to have a reasonable lengthwise overlap of the sheets and to have the lower edge slightly open for drainage - not fleeced and sealed over the horizontal joints.
I see what you mean, but so far I haven't had any complaints or problems
Absolutely right, seams should be avoided if possible and one whole long continue panel should be preferred.
Your right as the Landlord of my rental factory put bitumen over the lap joint and when water got in due to cracking the whole length of the roof became wet as the water could not escape. Now I have extensive rust and it impossible to locate the areas that are the problem as the water travels along before it starts to drip through. I had to break the whole seam open to allow the water to escape.
Whatveould you do? Just sealer and no fleece?
@andysurfer318 I would not seal seams. Repair top and bottom overlapping sheets independently.
Also try not to have sheeting installed as colums of overlapping sheets. Better installed as row by row. This reduces capillary action inside 4 layers of sheeting at junctions.
Sir you seem very knowledgable. I hired a handyman who did a bad install on a 12x20 Veikous car port. It leaks from all 3 seams inside, lapping is uphill and water leaks thorough. He also failed to remove the plastic protection for shipment on top of roof. 9 hours for me to remove except plastic under lapped metal and screws. What can i do to micky rig it to leak less on inside? Chaulk or turbo seal and tape. I'm 65 retired and trying to stretch dollar I spoke to a contractor who can do rebuild way $$$!
Do you have a product you could recommend for removing rust over large area?
Elbow grease
Yikes.. Did a roof inspection and found a rust hole starting on the metal ridge ( same type of roof in video ). Turbo seal dose not ship to five O?? And some small flash rust stating also in small spots. Not big but will clean and spot paint.Roof is very flat with just a small incline so water runs off. Like your feedback. Off to the hardware store for some flashing tape to temp seal the hole untill sunny day.
Very clever repairing 👏👏😍
Please wear a harness😱🥺😭
Does anyone knows name of similar product in UK
were can turbo poly seal be bought.
Can you get a different color of the silicon?
Hi, I have the same issue with my Room. Do you know any Roofer in North Hertford who can help me fix this issue?
Good Job 👍👍👍
Thanks 👍
Brilliant...thank you a zillion
welcome
Hi sir. Where I can buy the Turbo poly seal? Thanks 🙏🏻🙏🏻👍
I just used turbo poly seal to seal 3 seams on a patio metal roof. Some very good shit
Yes pretty good stuff
Letting that dry overnight just makes the gap larger between the two pieces of metal that overlaps. It's not going to dry flat . I'd squirt clear silicone and smash to two panels together while it's wet then do your turbo poly seal over it.
Your videos are excellent
thanks
Woooow! Thanks for the information! 👍👍
Any time!
One question I have a roof panel that was cut to short so the water is not getting into the gutter I do have a small off cut could this be used to extend the sheet?
yes
I've got the same issue between the seams and screws along the bottom row of roof panels on galvanised IBR just above the bull nose. Will these methods not trap the water between the overlapping panels above the treated area?
i don' think so. A little hard to understand what you are referring too.
Cómo puedo aplicar para trabajar alli
Thank you. From Australia. Why do you need the fleece?
G'day mate. Have a nice day
What is that tape like stuff you are putting down and sealing over?
It is Polyester Fabric, that comes with Turbo Poly Seal when you order it
I have a Green roof. I wish they could make Green Turbo Poly seal or perhaps green uv protectant
Wow you are up pretty high up.
Could you put down the name and who make these products please
Thank You
I have a metal roof and water is leaking in through some of the screws what will fix this
yes
I need help i'm a first time homeowner and I had a new roof put on my house and the roofer ruined 3 rooms of mine with leaks and I just want my roof to stop leaking do you do north carolina
Hey I’m in texas and have a flat metal roof with almost zero pitch. I have seams where they overlapped and almost left 3 inches of overlap. What do you advise and how much would you charge to come to texas and fix my roof ?!
You know water has to run off metal , it cant sit . He would probably torch down over it
Bravo ❤
do you still working?
I am in Brooklyn
I need roof fix
sure
I need this solution very much needed please help
Well, I don't think I can help where you are at
Can I ask what you would quoted for a job like this I want to get into it please do some videos on quoting jobs
I'm afraid to walk on my Mobile home roof like you do. First to clean it then to seal the screws heads and joints of a 13 year old roof Aluminum roof. Do u think it's ok to low crawl around up there?
Hey Frank
Start from the edge and slowly shuffle your way to the center and feel if the roof will support your weight.
The other thing you can do is to place 2 x 3 ft x 1/2" plywood that will disperse your weight when standing on them doing the job.
Cannot find Turbo Poly Seal in Australia! Anyone knows of an equivalent product?
We don't export and there is no other company that makes this composition
I hate when my safety glasses slide into my way while using my angle grinder 😂
I like " I know more than you, because I've done more than you."
Haha because he does. Look at those hands
Hello Doctor, very interesting to watch your video. Please tell me where can I purchase that Turbo Poly Seal and will that tuff can stand UV rays with the heat in Texas ? Many Thank
bergstromm.com/
Loved your videos! May I ask the name of the music at the end of the video? Which country’s style is it?
La Cucaracha
What ripe of paint do you recommend for a metal roofing?
If you just want to protect your metal roof against corrosion and rust, I recommend Aluminum Asphalt paint by Karnak. But don't paint the roof if you have leaks. First fix the leaks then you can apply a coating. It is very important to find all the leaks and wait a couple of months to be absolutely sure there are no leaks before you attempt any coating.
CAN this stuff be put on shingles
yes but be careful how you repair shingle roofs
@@FlatRoofDoctor what is the cloth like material YOU’RE using? Can you use it on nail holes on shingles? You know stuff Doc! Thank you for sharing your knowledge with the world🥇🥇🏆🏆❣️❣️
You can just pull off and replace a shingle
Oh boy, I had a brand new metal roof installed 3 years ago and so far it’s leaking in 7 different places. It’s a huge roof,50 square and I am so disappointed because it was so expensive and of course the roofers left state so now I’m stuck. They didn’t sheet it, instead used a silver bubble liner. My inexperience cost me big time. It’s an old slated roof and from the inside I see where they missed the slats and screws are showing right through the metal and wrap. Someone told me to caulk every single screw in the roof which would be a huge project. I’d absolutely do this if it’ll work but is this going to be a waste of a lot of time and money? Any suggestions from a true professional?
Like he says just, fix the leaks. It's all about finding them. You'd be amazed how much water will travel through a pinhole or an unseated screw.
Silver coating addition
Idea is to buy it in one sheet and the metal seams should of been sealed if your using 2 sheets. This is just putting a bandaid on the problem. The trailer roof you did would of been easier to lay metal down and it would of lasted a lifetime. I beat shingle prices with metal and that's why I'm a 5 star rated company. I warranty my work too.
What's the name of the product
Turbo Poly Seal
Preparation that's the key
yep, that is the basis for everything
very cute old man!
Is Your Business Just Repairing Metal Roof Leaks or What Else Do You Do .....I'm Curious.....Thanks
I install Torch Down Roofs too. I teach how to use a Torch.
I repair many roofs
Oh boy.
Good muti
yep
Water will seep up on the metal pc repair....never screw debris under washers
No knee pads,no gloves,no fall protection? Not even a dust mask when grinding !!. This ol guy needs learn few things! Look all the sht on his hands at 11:00 min in.. 😂
“Do I like coating … No”, then proceed to apply a black coating to it.
🙏😇
I don't see how you're still in business buying Turbo Poly Seal. It's $200 for one gallon, that's insane. Black jack eterna-kote is $300 for five gallons and way better.
Laquer thinner................DUDE! Where are your protective gloves?? OMG
i know, I am an idiot. But never learn
That's a big ass roof
🤦♂️
TOM PIPPS FOAM_ BATON ROUGE LOUISIANA USA HI HELLO &
I’m sorry, I don’t mean to be rude, but what a mess. There are far cleaner and more secure ways to repair a flat roof. At least use some masking tape for a more attractive finish!
I do not understand why you are always showing those kinds of metal roofs, and the leaks there can be repaired by anybody with little brain. I know you are an expert but such repairs are not a big deal....Nowadays nobody installs such metal on their roof except for owners of commercial buildings, farms or sheds!!! If you are that much skilled, show me how to repair my shingle metal roof! and then I will pray for your business and success !!!! It is leaking almost from everywhere especially where the roof is connected to the exterior walls, my exterior walls show all those leakage lines.... disgusting ......Helppppp
Hi Bill
There are not many people that have "shingle Metal Roofs". I am sorry that I have disappointed you with my videos. I am showing repairs that I run across in my business from day to day. You are expecting me to go out of my way to find something exceptionally just to help you.
I don't have those type of clients, sorry
@@FlatRoofDoctor you da man! Don’t listen to the haters.
If you do not use an oxygen disipating chemical seal first. It will rust under anything put over old rusty areas.
Believe me I'm in the auto body industry and I know what I'm talking about.
That's one of his past job failures, were he used duper silicon sealer to seal the whole roof, it didn't hold up, now he's back to fix the problem areas failing.
What a con artist this guy is.