Mm nice video hello there I’m trying to install my T6 thermostat but I only have four cables. The green one the red one, the white one and the yellow Can you give me some tips about it?
Good video, but there are NOT 2 spots to add your wired connections (3:50 in the video). There is the "inner" spot which is where the wires go, and where the video installer eventually puts the wires. The other "spot" is where the thermostat actually connects to the wall plate.
Question; I have a Honeywell wifi t-stat installed on the ground floor which is not a T-6. Do I need to install a separate app in order to use the T-6 for the second level stand alone hvac system, or is there a way to do it on the same Honeywell app? Thank you!
My Lyric 6 Pro's face stopped responding to my touch. I ordered a new thermostat. It came in today. I pulled the defective on off the wall and put the new one on. Mine did not show the temp. During the instructions it told me to set my phone (android) into airplane mode. Then it told me to go to the wifi devices. Now since I have my phone in airplane mode there is no internet. I remember having the same thing when I first hooked up my 1st Lyric T6. I kept reading the instructions, doing the same steps but going into circles. Honeywell had got to change the way the set up these thermostats.
Match up the connections and colors from the original thermostat if you have a picture or look at the heater controls and what terminals each color connects to.
We only have four wires. A blue/green/white/red. We have the Honeywell t6. Having problems with getting it to work correctly. Blue wire is labeled with a y Green is labeled with a g Whits is labeled with a w Red is labeled with a r
Yes, you need a C-wire to install it. Make sure you check the wires coming out of the wall and see if there is an extra. If there is, make sure it corresponds to the C terminal on the board in the unit. If you don’t have that wire, Honeywell does have an adapter that works well with older systems. www.amazon.com/dp/B07VMV2BJ7/ref=cm_sw_r_cp_apip_TNI3QB7SnY3Uq
VERY helpful video. It did not quite mirror our situation, but it was close enough so that we could figure out the rest. Thank you!
Mm nice video hello there I’m trying to install my T6 thermostat but I only have four cables. The green one the red one, the white one and the yellow Can you give me some tips about it?
I have gas heater only and no AC. And there’s only two wires on my thermostat Red&White. Will this model works on mine? Thanks!
Awesome video!
Good video, but there are NOT 2 spots to add your wired connections (3:50 in the video). There is the "inner" spot which is where the wires go, and where the video installer eventually puts the wires. The other "spot" is where the thermostat actually connects to the wall plate.
Is the trim piece mandatory?
Do you have a link to the other way of programming it
Question; I have a Honeywell wifi t-stat installed on the ground floor which is not a T-6. Do I need to install a separate app in order to use the T-6 for the second level stand alone hvac system, or is there a way to do it on the same Honeywell app? Thank you!
This is a great video! Thank you very much
My Lyric 6 Pro's face stopped responding to my touch. I ordered a new thermostat. It came in today.
I pulled the defective on off the wall and put the new one on.
Mine did not show the temp. During the instructions it told me to set my phone (android) into airplane mode.
Then it told me to go to the wifi devices. Now since I have my phone in airplane mode there is no internet.
I remember having the same thing when I first hooked up my 1st Lyric T6.
I kept reading the instructions, doing the same steps but going into circles.
Honeywell had got to change the way the set up these thermostats.
How to take out the thermostat, I can unlock the thermostat?
Saw red power wire (for heat). Don'r think I saw anything about wire for A/C cooling. ??
Make sure you look for any jumper wires and set the switches inside the mounting plate correctly
Can i install the T6 Pro with 2 wires and use it without Wifi?
I have same question and never answered us😢
The specs on this Thermostat says two AA batteries... where do they go??
I have an orange and a black wire in addition. Can you help me with that ? Thanks
Refer back to the picture of the installed equipment wiring diagram. Check the color connections on both ends and match to diagram.
I have a honeywell t6 pro series and I do not know where the yellow green blue red white and orange wire go can someone please help me
Match up the connections and colors from the original thermostat if you have a picture or look at the heater controls and what terminals each color connects to.
Is it the same installation for the Honeywell Home T6 pro?
We only have four wires. A blue/green/white/red. We have the Honeywell t6. Having problems with getting it to work correctly.
Blue wire is labeled with a y
Green is labeled with a g
Whits is labeled with a w
Red is labeled with a r
Mine just turned off completely what do I do
Question the old thermostat had a jump pin on the R -Rc, Do need the jump on the T6 Pro? thanks
Check the instructions as it has switches at the bottom of the mounting plate to accommodate jumpers
Do you need the c wire to operate??
Yes, you need a C-wire to install it. Make sure you check the wires coming out of the wall and see if there is an extra. If there is, make sure it corresponds to the C terminal on the board in the unit. If you don’t have that wire, Honeywell does have an adapter that works well with older systems.
www.amazon.com/dp/B07VMV2BJ7/ref=cm_sw_r_cp_apip_TNI3QB7SnY3Uq