Repairing A Wood Shutter
HTML-код
- Опубликовано: 7 сен 2024
- Repairing a Exterior Louvered Shutter - Wood Rot
Shutters are considered low-hanging fruit when it comes to adding a splash of color or curb appeal to a home.
DIY shutter repair can save you a few bucks in the process, but its NOT always worth doing!
Considering Repair vs. Replacement
I get asked this question a lot and here is the answer. The answer lies somewhere between show much rot is there and how much time will it take to repair.
If your a DIY-er its almost always worth fixing them to save money, but if your paying a carpenter $50.00-75.00 an hour it’s a much different story.
Repairing a shutter in decent shape can also save a lot of time prepping and painting.
If the shutter is not a high quality shutter, i.e., not made from Cedar, and doesn’t have quality joinery [see below] then I would have a carpenter devote no more than one hour to the repair.
If the repair is more than an hour, consider replacement shutters.
Prices range from $100 Basswood / Pine to $200+ for cedar shutters
Shutter Materials
what is the BEST shutter material?
When replacing shutters try to use vertical grain Western Red Cedar
Avoid anything finger-joint joiner.
Quality shutters always have mortise and tenon joinery. Mortise and tenon joints are strong, durable and stand the test of time.
How To Repair An Exterior Window Shutter
This shutter has rot in the middle connecting rail, so we’ll focus on replacing that rail.
Exposing the Connecting Screw
To remove the middle connecting rail you need to locate the fasteners which run through the shutter styles [long rails]
On this shutter, one screw was exposed and the other had a wood plug protecting and hiding it.
In order to get the wood plug out, and expose the screw, I took a 3/16″ drill bit and drilled out the plug.
The drilling simply creates an opening for you to use a screw driver, utility knife or nail punch to pry out the plug.
Once the plug was removed, remove the screw
Making the New Middle Rail
I used a 2×6 cedar board to make the replacement middle rail.
A table saw is the best tool to size the new cedar board.
On the table saw, I cut a clean edge on one side and then set the saw to cut the cedar board the exact width of the rotted bard. I then flipped the board on its side and rip it to the same thickness.
TIP: I don’t measure here, I simply place the old board against the saw blade and slide the saw fence to the board. Once the saw fence gently touches the board I secure the fence and cut into the cedar.
I then cut the cedar board length on a miter saw, squaring one edge first and then measuring and making the final cut.
Priming End Grain
I primed the exposed wood on the style rails as well as the ingrain on the middle board. End grain wicks moisture faster than any other part of the board.
This is why the middle rail rotted in the first place.
By sealing and back priming all wood trim you are giving it a chance to endure the elements by slowing water infiltration.
Fasten the Middle Rail In Place
The old dowels that used to be in this location had long since failed so I decided I would use two screws on each side.
I reused the old screw hole and then spaced out a new location. Pre-drilling and countersinking the hole to accept a wood plug is the best way to fill this hole.
TIP: A wood clamp can be useful for holding the middle rail in place.
Wood plugs look and weather better than wood putty.
If you’re looking to make a long term repair purchase a countersink bit and a wood plug cutter designed to fit into the counter sunk hole.
Paint Preparation
I then use sand paper to “break the edges [round them over] and clean all flat surfaces. A coat of primer and two coats of finish paint finish off this repair.
I see nothing but plastic chinese shutters going up all over southern Calif. It might look adequate 1/4 mile away, but looks like you know what walking by from the sidewalk. Glad to see some real skill from you guys and showing how to do it correctly.
I have a broken louver and can’t find anything on replacing one - seeing a few fall out on this video tells me it may be in my skill set, but I’d sure like to see it done. This is great!
I also have a few broken louvers and can't find anything on replacing them. I know it was 2 years ago, but did you ever find anything on this?
@@myrtlebeachtv I ended up cutting a grove on the back of the shutter to remove the broken louvre, then cutting a piece of similar thickness molding and rounding it over, inserting it into the empty space, bradding it into place and painting. From the front, you’d never know.
@@kenthomas1109 Thank you!
That was super helpful! Thank you!
Nice video, the point is that i have external shutters and are rotten in the stile that the louvers moving.
thanks #TBBcrew for the new giveaway and for the shutter repair video
And where to get the replacement louvres?? That's what I came here for...
Make them
The opening showed rotted wood as the problem which is what I'm dealing with but then the video is about replacing one of the planks. Bummer and poor set up on the video
Are you against carpenters making a living??!
Sev Massyn absolutely not, I’m a carpenter, why do you say that?
I appreciate your channel and expertise.
You mentioned that it wouldn’t be economical to pay carpenters a certain hourly rate for a specific job. Surely it is up to the buyer or client to decide.