How to Remove and FIX Door Handle on Alfa GT, 147, and How to Prevent it from Breaking
HTML-код
- Опубликовано: 6 сен 2024
- In this video you can see how to remove and fix door handle on Alfa Romeo gt, and 147...
Disclaimer: ARC Garage is not responsible for any work you perform on your car. If you're not confident in your mechanical and electrical skills, we suggest you take your car to a professional.
For 147 owners, procedure can be shortened a lot! I replaced mine today. After door card removal, you remove 10mm nut that holds the hinge to the door. Then you can remove broken part and use very long screw driver to reach phillips screw that holds the hinge to the handle. After that you open new hinge 180° and put it in a handle to tighten it. Then you pull handle as if you were opening the door, that will give you enough space to close the hinge to normal position. Put back 10mm nut and you're done. Much much faster than doing this whole procedure but applies only to 147.
Did it before with replacement hinge on 147, although it is much harder on GT. In this case I had to repair the hinge, thus the full handle removal...
Just wanted to write same thing. Easy job, done within 15 minutes 👍
Thanks, i will try that
It depends if the actual broken part is the front hinge. I pulled it apart and the front hinge was fine, my problem was the red plastic piece was worn and was not keeping the rod in place.
Ingenious 😍 I have faced this situation with my GT and even the Alfa garage I took it to replace the brand new door handle was not too keen . It’s a pig of a job and only for the brave to take it upon themselves. Only Alfa can make a door handle replacement so painful 🙄.
This demo really helps and I will try to prevent it happening to my other door since I now know what’s causing this problem . Thank you as always 🙏 very helpful stuff ❤️👍
I agree, it does require a lot of effort, and it could've been devised much simpler. Thank you very much for your support...
Done today. Took apart as you illustrate, but suspected it might have come out without undoing the top two rod links. I reassembled these with the handle out, and yes, it will go back in with the rods already attached, just check they are taking the correct route inside the door.
Hi , your video's make the life of the GT owners a lot easier . they are very usefull. thank you very much
Glad to hear that, thank you very much for support, it means a lot...
すごい!
新品パーツを交換するのではなくパーツごと修理するなんて初めてみた、素晴らしい発想力と技術!
Another excellent video! One thing: on my facelift 4 door 147, the door switch cluster is held in by a screw underneath the armrest. You can't simply pry the switch cluster out of the door.
Thank you, you got to be very careful, you don't want it breaking apart...
@@arcgarage For sure, especially for RHD 4-door cars, those switch clusters are getting very rare and expensive!
Brilliant this video is priceless. Saved me lots of money
I wish all automotive videos were thi s calibre
Thanks for support. Glad it helped...
Really useful! I'm gonna lube the hell out of it :))) How did you unglue the door handle plug? Any marks after?
Thanks, that is exactly what I did...
Great work, of course😍. I suffered two attempts to access the repair, I succeeded on the second attempt, without disassembling the part of the rods, forcing, pulling the part of the lock. I was wrong😠, buying a hinge, for fiat 500, the cheapest around €6 on e bay...(for alfa gt it is a lot more expensive, around € 25). I had to modify, fill with composite, the screw pitch ... A nightmare😱, that to save € 200, ended finally, well😳.
I will use the multipurpose oil on the passenger side so as not to repeat that bad drink😰. Thanks again for these videos😍
You're welcome, it is a nightmare of a job, that's why a bit of wd40 from time to time can prevent all that hustle. Anyway, I am glad it all ended well for you, the prices online are unreasonable, and thank you for support...
Just broke that hinge last Saturday! Great channel that helped me a few times already in the past few months (just bought a GT a few months ago).
Glad to help, thank you very much...
Do you need to replace the whole handle if it breaks on the barrel side of the handle
Very good guide, let's hope I won't need it 😁 would it be a good idea to put some grease over the metal repair strip to slow any corrosion further?
Thanks, it is made from metal that does not rust, and I have greased it good...
Absolutely genius with the glue stick method on the pull handle plug/ cap!!!
Wish I’d knew this years ago!!
How did you remove it? Hairdryer on the area?
Thanks, it removed fairly easy without any heat...
Awesome! Did it leave any marks on the surface? Thanks again!
good DIY sir
Hello from Algeria
Thank you! Cheers!
great job! will try this on my GT , passenger door handle broken by friend, I think this will be better then replacing with new one (made in PRC) and waiting to be broken again)
Go for it...
But i need adjust it because if i screw the screw in it will become hard also inside the one screw nut from the windows goes empty also in whistle at 100km +- with wind from the door what i can do?
Very nice tutorials bro thank you! I have learned so much things about my 147 :)
Glad to hear it, thank you for support...
veoma su mi korisni tvoji klipovi, svaka cast na radu, puno srece i uspeha u narednim radovima 👍
Hvala na podrsci, znaci puno...
Hi,this DIY,works for the alfa 156?thanks
Someone know the torx size of the doorhinge ? I have to replace one and dont want to buy a complete set
Can someone send me the link with this hinge, i need to buy new one, mine is the same as this one in the video, I found on the internet only for the fiat 500 that is not the same as this one in the video.
Great job! Would've liked to see you putting it all back together though, it looks like a pain getting those metal rods back inserted in the right holes. How did that go?
Thanks 👍, actually the assembly was much easier than disassembly...
Hey man. I think I’ve watched this video a dozen times. I got a facelift 5dr 147 with the passenger side handle not working. Took the doorcard off, the front hinge is fine, my problem is that the red plastic piece is worn out and it doesn’t keep the rod in place. But what I wanted to mention is that I looked inside the door and I only seem to have just one metal rod as opposed to the two shown in your video. I do have the yellow plastic piece in the handle but seemingly no second rod. Would that just be a difference between pre FL and FL or number of doors?
Not sure about the difference, but you can replace the plastic thing which holds it in place
I can not believe, yesterday my son broke handle on driver side
There you go...
Great job! I will try in my GT
Thanks. Go for it...
Can you do a video of how to restore faded or scratched interior plastic? Things like handles, window switches etc
Thanks great video!!
Thanks, you got a great video on the channel for window switch restoration. I will be restoring some of the other trim pieces as well...
hello, is it the same procedure for the alfa romeo gt? thanks for your videos.
It is almost the same, but it is actually easier
easier in the gt? thank you.
Nice job.I like your videos help me a lot fix my Alfa 147 😉.
Glad to hear it, thank you for support....
Thanks to the video, it helped me a lot in the repair
Great to hear, thank you for support...
Nice vid.
Can I use the same method on the facelift 147 from 2006?
The thing is that, the handle (on the passenger side) does not have a keyhole. And the car has central locking system.
Does this make any difference regarding the replacement of the handle?
Thank you very much.
Thanks, you can use the same method, it shouldn't make a difference
Hallo from Poland :)
Maybe next video about repairing broken mirrors :) That aluminium inside is really weak point of 147 and gt. I had this broken in mine and I bought used one, but after assembling i realised that is from RHD version of 147 :(
Hi, I repaired one mirror on my GT, but I got one aluminum on 147 to repair, so there will be a video in the future...
@@arcgarage So i wait for this :) You are doing great job! From which country are You?
Great channel Dave. You are aware that the hinges are available on eBay very cheaply?
Thank you very much, yes I am, but honestly I didn't want to wait for 10 days for them to arrive, not to mention that I would have to take the door apart again...
In Alfa Gt is mounted differently
Great work
Thanks
Thanks a million!!
You're welcome...
You can buy that part for £8 on eBay u don’t need to bodge it ??
I have bought just the hinges before, but I didn't want to wait 2 weeks for them to arrive. This still works though...
😏👍
What a f… voice..