DIY How To Use and connect arduino with 16 Relay Trigger 12V LM2596
HTML-код
- Опубликовано: 5 сен 2024
- Instagram : / unboxingchannell
How To Use and connect arduino with 16 Relay Trigger 12V LM2596 Power Control Module with Optocoupler Protection
thank you for watching
More videos / @unboxing.channel
Page Facebook bit.ly/2UWPj2C
link of the site bit.ly/2zgnvN2
Flash deals bit.ly/2Nbjq35
Code bit.ly/2Pyurwz
Arduino MEGA 2560 R3 bit.ly/2Pu953u
12v 16 Channel Relay Module Board bit.ly/2UJE3Gz
Wire bit.ly/2EYjfFR bit.ly/2SS1Cv9
5v 16 Channel Relay Module Board bit.ly/2Fdng8q
24v 16 Channel Relay Module Board bit.ly/2UKG7yd
5V 8 Channel Relay Module Board bit.ly/2OaN21d
5V 4 Channel Relay Module bit.ly/2Y5dI8d
5V 1 Channel Relay Module bit.ly/2Y7sCe
Great job lhaj ba3 dar! keep up the good work !
How to make rgb rainbow patterns for automatic stair case
if am use use 2 temperature sensor and 5 pc fan for cooling purpose
is it possible to run at separate and whole fan at same time..?
am lot of double actually is possible if not
how did i done this project..?
yes you can
@@Unboxing.Channel buddy did u explain how did u do
@@Unboxing.Channelthx for your reply am impressed
yes I did it
thank you bro😘
Excellent work. Please how can I use these relays to build automatic transfer switch with screen display?i will also be grateful if you add drawing
thank you
Hola, que arduino fue utilizado que modelo?
arduino mega
@@Unboxing.Channel muchas gracias !! 😁
you welcome
Peut on utiliser ce systeme pour piloter une machine comme une noyauyeuse ? En gros ce sont des verins pneumatique qui sont actionner par des electrovannes le tout orchestrer dans un ordre bien precis, et il y aurrait un bouton pour demarer chaque cycle, ainsit qu un "potentiometre" pour faire fluctuer un temps de gazage ?
i don't know but try it
The 5 volt on the relay isn't that an out to power your Arduino? I noticed you pluged the 5 volt relay to the 5 volt (power out) on the Arduino. I thought The 5 volt relay goes into the VIN on the Arduino.
this relay work with 12v
Hi, I got this exact 16 Relay Board from a friend, and one micro controller is blown, so only 8 relay Channels are available, more than anough for my need. When I give 12v, the small red Light, so I guess it is still usable.
So can I use an Arduino Board to control those 8 channels left, even I only need to control 2 relays for a start. If yes can you please orientate to a tuto?
Thx
you need to know the number of output of relay
Check the voltage at the relay coil it will be the same as the input voltage, a bad design the relay must receive 5vdc only, easy to fix.
this module work with 12v
Kalau mau pesen gmn caranya
product or what
How much time will you take to make video
Sir how to connect 32 relays channel
like this bro
Can you please make a video on (how to make double sensor automatic staircase light with 12v 16 channel relay module)
yes
great video, can you recommend some usages for at 12 car radio boom boks that i have made, thinking about bluetooth controlled? )
thank you bro
next project i will make arduino and bluetooth
What is max ampere threshold on power input of this relay module?
2a
How much ampere ?
10a
PLEASE NO STUPID UNNECESSARY STUPID MUSIC
thank you
Excellent job. How can I control these 16 relays wirelessly?
with arduino program
Bro i want to make automatic on/off stairlight system with arduino nano and 12v relay module
yes you can
Can you plz tell me how its possible
i need time
Thanks very much !
you welcome bro
Can u add a circuit diagram in the description
facebook.com/notes/unboxnig-tools/how-to-use-and-connect-arduino-with-16-relay-trigger-12v-lm2596/2373815672941333/
hi.. it possible to add 32 channel relay to single board?
yes you can do this with arduino mega
@@Unboxing.Channel Arduino Mega 2560 Rev3?
yes www.banggood.com/Geekcreit-MEGA-2560-R3-ATmega2560-MEGA2560-Development-Board-With-USB-Cable-p-73020.html?akmClientCountry=MA&p=JA11188949702201702C&cur_warehouse=CN
can i use arduino uno instead of the mega ?
if you use arduino uno you can't use all this relay maybe just 9 or 10
Circuit diagram link please
ok
facebook.com/notes/unboxnig-tools/how-to-use-and-connect-arduino-with-16-relay-trigger-12v-lm2596/2373815672941333/
Hey bro! Can you help me out? I’m trying to control my relay using data thats being sent from a websocket to port 9001. I need the arduino to read data thats being sent to that port. Whenever the websocket sends a specific line to the port (like “Avatar/Dynamics/Haptic1”) the relay pin 1 allows electricity to flow. and whenever it sends “Avatar/Dynamics/Haptic2” the relay pin 2 turns on. Can you help me out? I have no idea how to code this.
can be difficult
@@Unboxing.Channel Hey man! Got it working a week ago. Your video was amazing keep up the good work
thank you so much bro ❤❤❤❤
Hi bro ,how much time will you take to make video
1 day 😁
How to connect ultrasonic and 12v 16 channel relay module to arduino nano
ruclips.net/video/sj8VX3_EGTo/видео.html&ab_channel=UNBOXING
ruclips.net/video/DwEzjzgOzoU/видео.html&ab_channel=UNBOXING
In that case, did you have to use two separate power supplies, 12v and 5v?
yes of course you need two power supply
or just one power supply 12 and regulateur to take 5v
@@Unboxing.Channel Ok, thank you.
you welcome bro
@@Unboxing.Channel for what the 5v, 12v just is required to run the board, and there is a regulator to stepdown to 5v.
But what can be done it that board ? I got one catually, but dont know how toautomate thing when it....
can i use three 16 channel relay with one arduino mega without blowing?
you mean use arduino mega with 3 module 16 relay
You probably shouldn't power the three modules from the arduino as the USB port will not support current that high. Figure out the current draw of one relay module and the multiply that number by three. This is the worst case scenario, especially if your design will not require all the relays to be powered at once, but could happen if your code has a bug.
✌✌
What can I use to make a wireless controller for this 16 relay channel
you can make (automate programmable)
how to edit coding proximity sensor stair up and down
🥰
Hi
🖐🖐
Hello bro
hi bro
Is it possible
yes
What a crappy video. Cant see what wires go where.
it is very simple