2004 lexus sc430, car was a complete shitshow of jumped wires, burned up connecters, a bad ecm, immobilizer bypassed smh. repaired electrical issues replaced ecm with used unit,had a new key cut and programmed. this procedure fixed the post repair start stall condition! ACES THANK YOU!!!!!!!!
Works like magic on a 2005 Toyota Camry My car had transmission issues that never left even after fixing the issue of solenoids. My mechanic who a genius recommended I change the ECM or in other words Car Computer. I went to the junkyard got a used ECM for $30. I replaced it(ECM) but the car refused to start. I kept using the old ECM until I watched this video. I did the 30mins and came back to start the engine after removing the paper clip from OBDII. The ECM from the junkyard started the car like magic. No more transmission issues and the car starts and runs like a beast. Thank you very much for the video!!!! I saved >$300 on programming a computer that I wasn’t sure it was going to work. This method is easy and precise and accurate.
Wow good for you friend, I have the same problem, I bought a ECU from junkyard, but the car refuses to fire up, only cranks, my is a 2001 Hyundai Santa Fe 2.4 engine manual transmission. Do you think this process will work on the junkyard ECU, it's for the same make and model just different year. Please let me know thank you...
Did you try this fix on tour original ECM? I have a 2010 Sienna that went into limp mode and threw a bad solenoid code. After replacing the solenoid, the Sienna was still stuck in limp mode with rpm under 3500 and couldn't accelerate past 3rd gear (~28 mph) but no longer produced any codes. I assumed something like the ECU or TCM needed to be reset.
I bought a 2001 Lexus LS430 from an impound but had no key. I called out a locksmith and had a key cut and programado the car but would not start. I plugged my obd2 scanner and got a code for the immobilizer malfunction. I tried multiple things called out locksmith to come check it out and no one can figure it out after trying this method. I can happily say it worked. Thank you so much for posting this video. You saved me so much money.
finally found the video again, used this video last year when my yaris was jerking a crazy amount and has slightl started to again, so back here again!! ur a legend mate
This was very helpful. After all mechanic having all things to say about putting it on the computer to charge me a lot. I tried this method with my fingers crossed to my 2007 toyota mark x and indeed it worked.. This video was AWESOME..🙏🏿🙏🏿🙏🏿🙏🏿
I am currently trying this “paperclip reset” on my 2004 Toyota Solar. So far it is doing everything your video described in regards to the flashing lights on dash. I am currently 20 minutes in on the 30 minute wait time. I am patiently optimistic from reading the previous post and will post my results shortly…. It initially didn’t work but after 2 more tries.., it started!!!!!❤😅😊
I know this has been around a long time. However, thank you very much for this video. I had a Toyota RAV4 2.0 D-4D 2005 model ECM repaired due to water damage. The repair involved various components being replaced. Net result, refitting the ECM, the car would not start. I almost ended up sending the ECM for repair again, but it felt like the immobiliser or security of sorts that was causing the car to not start. Your video is all that was needed. I dusted off my most prized paper clip and reset the ECM. Bingo, the car works & is stable Thank you.
I was hesitant to do this to my 2014 sequoia but i took a chance and it worked! Parked the car last night and this morning it wouldn't start. Tried several things before doing the paperclip trick and 30 minutes later it started right up. Thank you
Had a Toyota Sequoia that turned but couldn’t crank after replacing the ECU immobiliser, tried everything at the shop with all the guidance from TIS but nothing worked after watching this video while taking a break I went ahead and tried it and it worked so perfectly, was such a relief....thanks man
I used this on a 2008 Prius, I lost my key fob. My solution cost $70, I got a key fob, immobilizer ECO and the main ECU all from the same car. After installing these the car turned on but no READY light. After jumpering pin 4 and 13 for 30 minutes the car started. Many Thanks and I thank God for you and others that post useful information!
Hey John. My case is kinda similar. 2006 Prius. My key fob stopped to work. I have another key fob from a different prius. Can I program this key in my Prius with this steps without replacing the immobilizer, and main ECU?
Had an accident with a 2007 toyota Mark X 3.0 V6 (japan import) - air filter and radiator were whipped. After installing the missing parts, car started but showed dramatic rough idle and overeating. Tried the procedure and it worked perfectly - everything went back to normal. I was even able to see diagnostic tests on the info screen... Thanks a lot !
2011 RAV4.... this fix worked for me too. I was busy working on the spark plugs & injectors all day, didn't notice the battery was being drained by the lights being on. I had taken out the EFI fuse & the fuel relay. After I recharged the battery, neither of the remotes worked! This "fix" made the remotes work again, but now, the ABS and BRAKE and squiggley lines (brake related) are all on. I wonder why? But, this fix worked to get the immobilizer working again. thank you.
BRILLIANT! You taught this old retired mechanic a new cheat! ------ Um , short cut! Who says you can't teach an old dog new tricks? I hope this works on U.S. spec Toyota and Lexus models. Great vid as always Gerard!
I have a 2018 hilux that I bought with no keys.. I replaced the immobiliser and had new keys programmed still wouldn’t start ... used this technique and it started first go ! Thanks so much very helpful video 🙏🏻🙏🏻🙏🏻
Any one find out wheee is the immobiliser box ? I have same issue my car crank but won’t start mechanic checked every single fuse all good. 2020 Hilux any one car help please ?
You did me so much help on this video I had a Bully Dog programmer had an error during programming I had to spend off my computer to them and they returned it to stock but Upon returning to my truck it would not it would start and turn off right away well I put it on a scanner found out that the immobilizer was active and this video with a paperclip and number four and number 13 let it sit for a half an hour I didn't shut off the ignition pull the paperclip and my truck runs perfect thank you thank you thank you
Thanks for this video. it helped me tremendously. You can add to your list a 2016 Tacoma. it worked for me. A word of caution, the position of the plug is critical, it took me a while to figure it out because the the plug was backwards, lower side on on top.
I can confirm this worked on my 2003 sequoia limited. Replaced the ecu, it would only crank had immobilizer codes. There is a separate immobilizer computer and the cluster recognized the keys but still wouldn’t start. Did the pin jumper for 30 mins, cranked the truck and it started right up. Codes were no longer there.
A huge thanks to you! Helped me with my alarm/anti- theft issues on my 02 Camry LE. Alarm would go off not allowing me to start the car. I disconnected the immobilizer/ anti-theft module, then I used your method and finally got the car to start. Hopefully it won’t give me anymore problems in the future.
What problem were you having? Currently I'm having issues where the car isn't recognising my key fob and not opening when I'm near it and sometimes won't start with the key inside
Worked on my 2003 Avalon....as far as I can tell key had to be “on” one click past acc to get all of the lights flashing. Also didn’t work the first time, not sure why. But second time I let it go 45-50 minutes and made sure to turn ignition off before attempting to start. Thanks... I will make sure to leave a paper clip in the car from now on!!
My gx470 2003 doesnt see key too. It cranks but wont start, that car with key flashing red blinking. I think it shouldnt while cranking Hopefully it will help on mine. I try tomorrow
Hey Samson Brown. Did you have to crank the engine or turn it over for whole 30 minutes or did you simply turn ignition just to engage the dashboard lights? Let me know, thanks
Great video. My immobilizer light would not turn off more frequently and the car would just crank but not start. So I'm pretty sure that the immobilizer is the culprit because when that happens, I'd turn on and off the panic button a couple of times and the immobilizer red light turns off once I re-insert the key then it start right up. So I'm wondering if this will work if I purchase a used ECU without keys for 99-05 GS 300/400?
I'm not sure if this is useful without master key if I get a blank key cut from vin and it's a blank chip can it turn on ignition like this did as to reprogram or zero codes to program key blank
Most interesting. I understand this focuses on Toyota/ Lexus but by any chance do you happen to know if there is a similar fix for a Peugeot 308 T7 2010 ? Cheers
Why it can't be used to program new key? After reset the immobilizer, car will go to the register mode and accept any key, including the new key, right? Am I missing something?
Hi nice vid, thx. In another vid they recommend to start the car after this procedure and leave it running for about 10 minutes for it to relearn. Regards
I had to change the battery on my 2016 Tundra, after that it never start no more. It crank but do not start, my friend technician came with his computer, we tested all fuses and relays, all good! But the computer could not be connected to the ECU (no ECU connexion). Do you think if I do this process it will work? Thanks
Hello man , I was working on a 98 Toyota 4runner sr5 3.4 v6 for a buddy . I wanted to do this procedure since the guy already changed his brain and nothing works. No crank no spark and no injector pulse. But I am confused after looking at the obd 2 plug it only has 3 wires coming into it on the back and it was either pin 4 or pin 13 wasn't even there. Any ideas ? I'm a professional mechanic but that one's got me. I told him to tow it to a dealer but I would like to help him
Where is this plug that you put the paper clip in? Also, if your security system trips, will it allow you to turn on the dash lights when you press the start button? My dash lights come on when I press the start button but my car ICE won't start. It started before I changed out my hybrid battery pack. Now, the dash lights come on but the ICE won't start. I also see every single light on the dash coming on.
Was this procedure used to reprogram the Engine Control Module or the Body Control Module? My key FOBs suddenly stopped working & the diagnostics performed are pointing to a faulty Body Control Module, located behind the driver side, instrument panel junction block. I've located a functioning replacement Body Control Module. So, which were you reprogramming?
Will this work on my 2001 Lexus RX300? My original ECU is acting strange when it's cold and sat overnight and I am buying a used ECU to try to flash it with my original keys.
There is a video on RUclips where the guy pulls out the ECM and replaces the two pin barrel capacitors that tend to leak acid on the board. I will try and find the link and post it here.
I have a Lexus is220d keyless entry and I lost my keys. I bought a new ecu with the key but the car doesn’t want to load the ignition at all like in the video. I just get the no key detected message. I just get the alarm beeping constantly, do you have any recommendations?
I have an 07 Camry that hit a deer and put out headlight driver side, no bag deployed no leaks or anything car was still running fine but when it was shut off it no longer cranks the cooling fan comes up and you hit the brake push start button goes green but no crank any ideas?
Excellent, We have a 2009 Toyota in the workplace at the moment with a start up malfunction error code tried the spare key but with no luck, Could this be a common fault with barrel and key losing paring I wonder if this method is worth a try? All the best Mike.
This is not resetting ecu nor immobiliser but its linking ecu to immobiliser after ecu has bin replaced. It's called handshake. On newer cars ecu and immobiliser are two separate computers. so its linking new ecu to immobiliser system. On older cars immobiliser is one with ecu and this will not work. good video just little misleading wording.
I had to jump my 08 sienna and now I've somehow engaged immobilizer. my key will not unlock the ignition switch to start the car. will this allow me to "reprogram" my key to the vehicle?
@@johnfoster4827 I cannot follow all the backdrop you have not included. Like key cannot activate ignition. You have not included your specific vehicle.
Hi, i did an engine swap along with the ecu.. my problem now is, car cannot start, cranking only. Im guessing the new ecu does not recognise the key.. will this trick works? Lexus GS300
2005 camry 2.4 motor swapped now the fuel pump doesn't kick when turning the key. Injectors don't fire either when fuel pump is hard wired. Trying this to avoid Toyota prices on reprogramming (pretty sure they're just doing this anyways) will update in 30 minutes.
1999 Toyota Solara with new key ignition cylinder with 2 new keys - i don't have the old keys - mentions at 1:43 that this can reprogram keys as well. I reset the ECM per his instructions. How can I program the new cylinder/new keys to the current ECM?
Hi, hope you can help. I have 1999 Avalon with security blinking and unable to start engine though it does crank. I also have a after market key ignition cylinder and new key. Where you unable to start your engine as well? If so, did this reset method work? i'm just afraid of shorting circuit and making a bigger problem and just confirming before proceeding. -thanks.
2004 lexus sc430, car was a complete shitshow of jumped wires, burned up connecters, a bad ecm, immobilizer bypassed smh. repaired electrical issues replaced ecm with used unit,had a new key cut and programmed. this procedure fixed the post repair start stall condition!
ACES THANK YOU!!!!!!!!
Thanks very much for sharing your feedback, delighted I could help you out.
Coming hot to working and I'm off ING after not working
You have been unlucky, mine is like a dream.
T
If u can help me i have a 2006 infiniti m45 i need to reset my key and ecu pls
Just stole this 04 4Runner, it worked!! Now it’s my 4Runner. Thank you!
lmao
Ha ha ha ha :)
😂😂
It worked perfectly on Toyota Rav 4 2010 model. God bless you!! You saved me from headache and losing money 👍
Works like magic on a 2005 Toyota Camry
My car had transmission issues that never left even after fixing the issue of solenoids.
My mechanic who a genius recommended I change the ECM or in other words Car Computer. I went to the junkyard got a used ECM for $30. I replaced it(ECM) but the car refused to start. I kept using the old ECM until I watched this video. I did the 30mins and came back to start the engine after removing the paper clip from OBDII. The ECM from the junkyard started the car like magic. No more transmission issues and the car starts and runs like a beast. Thank you very much for the video!!!! I saved >$300 on programming a computer that I wasn’t sure it was going to work.
This method is easy and precise and accurate.
Wow good for you friend, I have the same problem, I bought a ECU from junkyard, but the car refuses to fire up, only cranks, my is a 2001 Hyundai Santa Fe 2.4 engine manual transmission. Do you think this process will work on the junkyard ECU, it's for the same make and model just different year. Please let me know thank you...
Did you try this fix on tour original ECM? I have a 2010 Sienna that went into limp mode and threw a bad solenoid code. After replacing the solenoid, the Sienna was still stuck in limp mode with rpm under 3500 and couldn't accelerate past 3rd gear (~28 mph) but no longer produced any codes. I assumed something like the ECU or TCM needed to be reset.
I bought a 2001 Lexus LS430 from an impound but had no key. I called out a locksmith and had a key cut and programado the car but would not start. I plugged my obd2 scanner and got a code for the immobilizer malfunction. I tried multiple things called out locksmith to come check it out and no one can figure it out after trying this method. I can happily say it worked. Thank you so much for posting this video. You saved me so much money.
How exactly did you program the key I'm having the same issue did the key just work after 30mins
Does the imobilizer system entered in learning mode after the ECU reset?
finally found the video again, used this video last year when my yaris was jerking a crazy amount and has slightl started to again, so back here again!! ur a legend mate
Did the Yaris have transmission shifting issues?
What year is your Yaris? I have a 2000 that’s not starting
This was very helpful. After all mechanic having all things to say about putting it on the computer to charge me a lot. I tried this method with my fingers crossed to my 2007 toyota mark x and indeed it worked..
This video was AWESOME..🙏🏿🙏🏿🙏🏿🙏🏿
I am currently trying this “paperclip reset” on my 2004 Toyota Solar. So far it is doing everything your video described in regards to the flashing lights on dash. I am currently 20 minutes in on the 30 minute wait time. I am patiently optimistic from reading the previous post and will post my results shortly….
It initially didn’t work but after 2 more tries.., it started!!!!!❤😅😊
Thank you for your persistence and information! This helps too!
I know this has been around a long time. However, thank you very much for this video. I had a Toyota RAV4 2.0 D-4D 2005 model ECM repaired due to water damage. The repair involved various components being replaced. Net result, refitting the ECM, the car would not start. I almost ended up sending the ECM for repair again, but it felt like the immobiliser or security of sorts that was causing the car to not start. Your video is all that was needed. I dusted off my most prized paper clip and reset the ECM. Bingo, the car works & is stable Thank you.
I was hesitant to do this to my 2014 sequoia but i took a chance and it worked! Parked the car last night and this morning it wouldn't start. Tried several things before doing the paperclip trick and 30 minutes later it started right up. Thank you
Can you please tell me the location of this conector im having the same problem
@@martinreyes897
That is the most obvious connector throughout every vehicle on planet earth.
OBD 2.
Had a Toyota Sequoia that turned but couldn’t crank after replacing the ECU immobiliser, tried everything at the shop with all the guidance from TIS but nothing worked after watching this video while taking a break I went ahead and tried it and it worked so perfectly, was such a relief....thanks man
i have a 2002 that i’am gonna try this on. truck runs but randomly shuts off while driving! key symbol is flickering red. hopefully this works
What year was it ?
@@kingpremo2341 did you find the cause of your problem?
I’m hoping this works for my Lexus gs430 2006
When replacing IMMOBILIZER do you disconnect battery before
I bought a used ecu for my Camry and did this and it worked! Thank you very much. This is very helpful!
Witch camry modile?
@@aasa2022 THe one with 4 wheels. Hope that helps!
Did you leave your old keys in the ignition ? I have a blank key but I don’t know if it will work
I used this on a 2008 Prius, I lost my key fob. My solution cost $70, I got a key fob, immobilizer ECO and the main ECU all from the same car. After installing these the car turned on but no READY light. After jumpering pin 4 and 13 for 30 minutes the car started. Many Thanks and I thank God for you and others that post useful information!
Hey John. My case is kinda similar. 2006 Prius. My key fob stopped to work. I have another key fob from a different prius. Can I program this key in my Prius with this steps without replacing the immobilizer, and main ECU?
@@NAVERSCdid you ever find out if this worked?
2008 pruis had to change ECU now I'm going to try this because since changing it my key p
Fob doesn't work
@@jenniferhendrix8713 How did it go?
Had an accident with a 2007 toyota Mark X 3.0 V6 (japan import) - air filter and radiator were whipped.
After installing the missing parts, car started but showed dramatic rough idle and overeating.
Tried the procedure and it worked perfectly - everything went back to normal. I was even able to see diagnostic tests on the info screen...
Thanks a lot !
Keyless start/stop
2011 RAV4.... this fix worked for me too. I was busy working on the spark plugs & injectors all day, didn't notice the battery was being drained by the lights being on. I had taken out the EFI fuse & the fuel relay. After I recharged the battery, neither of the remotes worked! This "fix" made the remotes work again, but now, the ABS and BRAKE and squiggley lines (brake related) are all on. I wonder why? But, this fix worked to get the immobilizer working again. thank you.
Was this a 3.5 2gr Fe?
I can confirm that this works on a Toyota Auris mk1.
Thanks man. Really helpful!
Thanks for the info
Do you think it’d work on my Toyota Yaris?
This video was extremely helpful. It worked on my 2005 Toyota Noah.💯👍
Worked for my 2005 Toyota matrix you’re a life saver man👍
BRILLIANT! You taught this old retired mechanic a new cheat! ------ Um , short cut! Who says you can't teach an old dog new tricks? I hope this works on U.S. spec Toyota and Lexus models. Great vid as always Gerard!
Thanks Shep :)
I have a 2018 hilux that I bought with no keys.. I replaced the immobiliser and had new keys programmed still wouldn’t start ... used this technique and it started first go ! Thanks so much very helpful video 🙏🏻🙏🏻🙏🏻
Great News Josh, thanks for sharing
Hii josh..can u tell me what the problem your hulix..i had a same problem..
Hi Josh, dis this reset your ecu or was this purely to program key?
Hi. I have 2018 hilux too. Replaced ecu. Might try to do this. Where is immo box in 2018 hilux please?
Any one find out wheee is the immobiliser box ? I have same issue my car crank but won’t start mechanic checked every single fuse all good. 2020 Hilux any one car help please ?
Second generation prius, after hv ecu replacement worked like a charm, thank you :)
Thanks for the comment, I’m trying to do mine as well and needed some reassurance this would work!
You did me so much help on this video I had a Bully Dog programmer had an error during programming I had to spend off my computer to them and they returned it to stock but Upon returning to my truck it would not it would start and turn off right away well I put it on a scanner found out that the immobilizer was active and this video with a paperclip and number four and number 13 let it sit for a half an hour I didn't shut off the ignition pull the paperclip and my truck runs perfect thank you thank you thank you
So anybody with a 2007 Toyota Tundra that the CCT in DCU are not communicating this works perfect to take the immobilizer offline beautiful
@@dougabrams8632 What in the world. Why did you say “take the immobilizer offline”?
Used this technique on a 2010 Tundra and was successful.. Thank You for the knowledge..
I appreciate you posting up that info Tom. 👌👍
@@GerardBurkeBurkesGarage will this also get the tpms closed loop unlocked
2019 Toyota C-HR 2.0 worked with this method after ecu replacement. Thanks!
Works on 2009 Corolla USDM 5 speed! Thank you so much, dealer wanted to charge me 150 dollars.
Very nice video, I am locksmith and is really helpful
This method worked on a 2003 Corolla d4d with DTC error B2799. Huge thanks!
Thanks for the kind words, it's great it helped you out
Nice work and thanks for your teachings
This worked on a 2011 toyota corolla LE!! Thanks so much!
I can confirm that this method worked for a 2007 Lexus ES350
I know you posted this 4 years ago but why did you change the ECU? I have an 08 and I can't get rid of a p0560 code. I was thinking about swapping it.
Thanks for this video. it helped me tremendously. You can add to your list a 2016 Tacoma. it worked for me. A word of caution, the position of the plug is critical, it took me a while to figure it out because the the plug was backwards, lower side on on top.
Good man yourself. Works on a 2011 Toyota Camry LE 2ARFE 2.5L engine.
I can confirm this worked on my 2003 sequoia limited. Replaced the ecu, it would only crank had immobilizer codes. There is a separate immobilizer computer and the cluster recognized the keys but still wouldn’t start. Did the pin jumper for 30 mins, cranked the truck and it started right up. Codes were no longer there.
A huge thanks to you! Helped me with my alarm/anti- theft issues on my 02 Camry LE. Alarm would go off not allowing me to start the car. I disconnected the immobilizer/ anti-theft module, then I used your method and finally got the car to start. Hopefully it won’t give me anymore problems in the future.
Yoooooo can we talk I need more info
Did you leave the immobilizer disconnected?
Does the key in the ignition have to be an old key,? Or can it be a never-programmed key?
Did you ever try it? If so Can you confirmed if it worked for you?
interested in the answer to this question
Still waaaiiitttiinnggg for the answer 2 yrs later 😂
Thank you! Worked out on a Toyota Sienna minivan 2002 model.
Would a resistor in line to connect the 2 pins protect electrical spikes?
2006 is250 - worked very well. Thank you.
What problem were you having? Currently I'm having issues where the car isn't recognising my key fob and not opening when I'm near it and sometimes won't start with the key inside
This just worked on my 2006 Lexus RX400h (US).
Thank you!!!
Did you come across videos for working on your ecu?
Excellent. Worked on 2009 Lexus is250
Simple, clear and short video. Thank you. I subscribe then.
Worked on my 2003 Avalon....as far as I can tell key had to be “on” one click past acc to get all of the lights flashing. Also didn’t work the first time, not sure why. But second time I let it go 45-50 minutes and made sure to turn ignition off before attempting to start. Thanks... I will make sure to leave a paper clip in the car from now on!!
It didn't work the first time because you did not turn the key off, in order to finalize the reset procedure, that's all.
@@JohnSmith-ok9sn my friend do you think this process works on 2001 Hyundai Santa Fe 2.4 engine manual transmission.
Did you lose all of your keys and then have a new transponder key cut?
@@JohnSmith-ok9sn John, Thanks for this tip!
Just worked on a 2006 Lexus GX470. Thanks for the video!
Thanks for the comment and the info.
My gx470 2003 doesnt see key too. It cranks but wont start, that car with key flashing red blinking. I think it shouldnt while cranking
Hopefully it will help on mine. I try tomorrow
Hey Samson Brown. Did you have to crank the engine or turn it over for whole 30 minutes or did you simply turn ignition just to engage the dashboard lights? Let me know, thanks
Does this work to program a key and computer?
Just to be sure you said this does fix the start stall from the immobilizer?
Great video. My immobilizer light would not turn off more frequently and the car would just crank but not start. So I'm pretty sure that the immobilizer is the culprit because when that happens, I'd turn on and off the panic button a couple of times and the immobilizer red light turns off once I re-insert the key then it start right up. So I'm wondering if this will work if I purchase a used ECU without keys for 99-05 GS 300/400?
Thank you brother … from Iraq
I love your video intro splash screen! :)
I'm not sure if this is useful without master key if I get a blank key cut from vin and it's a blank chip can it turn on ignition like this did as to reprogram or zero codes to program key blank
Most interesting.
I understand this focuses on Toyota/ Lexus but by any chance do you happen to know if there is a similar fix for a Peugeot 308 T7 2010 ?
Cheers
Why it can't be used to program new key? After reset the immobilizer, car will go to the register mode and accept any key, including the new key, right? Am I missing something?
Did you get an answer?
@@pete900000 Do you did the process? Does the imobilizer system entered in learning mode after the ECU reset?
Seems like you just got another subscriber. 👍👍👍👍
Hi nice vid, thx. In another vid they recommend to start the car after this procedure and leave it running for about 10 minutes for it to relearn. Regards
I had to change the battery on my 2016 Tundra, after that it never start no more. It crank but do not start, my friend technician came with his computer, we tested all fuses and relays, all good! But the computer could not be connected to the ECU (no ECU connexion). Do you think if I do this process it will work? Thanks
DID YOU FIX IT?
Thanks for gevigg nolage this was sumthing new
Hello Sir, can you please tell me what is PIN 13 purpose.
Hello man , I was working on a 98 Toyota 4runner sr5 3.4 v6 for a buddy . I wanted to do this procedure since the guy already changed his brain and nothing works. No crank no spark and no injector pulse. But I am confused after looking at the obd 2 plug it only has 3 wires coming into it on the back and it was either pin 4 or pin 13 wasn't even there. Any ideas ? I'm a professional mechanic but that one's got me. I told him to tow it to a dealer but I would like to help him
Very good master
Thanks for the video. If I want to program a 2nd key, can I just repeat the process?
Where is this plug that you put the paper clip in?
Also, if your security system trips, will it allow you to turn on the dash lights when you press the start button? My dash lights come on when I press the start button but my car ICE won't start. It started before I changed out my hybrid battery pack. Now, the dash lights come on but the ICE won't start. I also see every single light on the dash coming on.
Is there supposed to be a loud humming from the engine bay during the 30min?
Worked on 2006 Sequoia Thanks a lot Sir
nice thx i have a 07 sequoia going try this
Galen--Did it work on the 2007 sequoia?
How long did you leave the paper Clip plugged in for?
Was this procedure used to reprogram the Engine Control Module or the Body Control Module? My key FOBs suddenly stopped working & the diagnostics performed are pointing to a faulty Body Control Module, located behind the driver side, instrument panel junction block. I've located a functioning replacement Body Control Module. So, which were you reprogramming?
Will it work with a smart key
Thank you ! Worked on 2002 rav 4 after ecu swap
Ciao su un Rav 4 con non resetta. L'immobilizer sai come posso fare?
did your rav have the rough shifting issue? was it fixed? I have an 03
What about the LS460 with push button! Also do you do the procedure with battery connected or not?
I did it, it's good.
Did this to a 2008 Toyota Rav4, it worked! THANKS
Thanks for the feedback Jeanne,
I get a scion tc 2006 its work for me?
@@juancarlosgarcia7323 ⁰
This will erase all coded keys linked to the car?? If so how do I reprogram the masterkey?
I wonder if this will work with a 2014 volkswagen jetta
Is this only for when you replace the immobilizer or the ECU? Will this work if I get the immobilizer code as well?
this method worked for my Toyota Prado 2006 3.0 Turbo Diesel after replacing the e.c.u
Thanks ,worked on toyota fortuner 2013 👍👍👍
Woow really work OMG thanks man 😊😊😊
Worked on my 2004 Camry LE V6. 😊
Great stuff Nick 😊
Yoooo can we talk I need more info lol
Will this work on my 2001 Lexus RX300? My original ECU is acting strange when it's cold and sat overnight and I am buying a used ECU to try to flash it with my original keys.
There is a video on RUclips where the guy pulls out the ECM and replaces the two pin barrel capacitors that tend to leak acid on the board. I will try and find the link and post it here.
Will this trick get rid of the tune I have on my is350?
Definitely worked for a 2012 Lexus rx 350!!!
what was the issue you were having with it?
I have a Lexus is220d keyless entry and I lost my keys. I bought a new ecu with the key but the car doesn’t want to load the ignition at all like in the video. I just get the no key detected message. I just get the alarm beeping constantly, do you have any recommendations?
I have an 07 Camry that hit a deer and put out headlight driver side, no bag deployed no leaks or anything car was still running fine but when it was shut off it no longer cranks the cooling fan comes up and you hit the brake push start button goes green but no crank any ideas?
nice video ,,this works on Toyota 4runner v6 2002
I really appreciate you bro
Can this work on any benz car?
Any chance it works on a 2007 lexus rx350 to reset VSC?
Works on 2014 Toyota Corolla one try after replacing ECU
Thanks saved my day!
Thank you for your video,that’s quite simple
Man, I really hopes this will work for my 2001 4runner limitied. I will let you know. thanks.
Hey did it ever work?
work?
worked on a 2004 4runner
What is reflashing the ecu really resetting? Is this also resetting or eraseing the keys codes too?
Excellent, We have a 2009 Toyota in the workplace at the moment with a start up malfunction error code tried the spare key but with no luck, Could this be a common fault with barrel and key losing paring I wonder if this method is worth a try? All the best Mike.
Did it work?
The video is fantastic! Thank you Do you know the pins connectors for a 2006 Scion tc
What about older Toyota Camry 2004
is the 16 port plug the OBD port? thanks for the vieo - i need to try on my 2008 Hiace van.
This is not resetting ecu nor immobiliser but its linking ecu to immobiliser after ecu has bin replaced. It's called handshake. On newer cars ecu and immobiliser are two separate computers. so its linking new ecu to immobiliser system. On older cars immobiliser is one with ecu and this will not work. good video just little misleading wording.
Hello friend one question, do you think this trick would work on a 2001 Hyundai Santa Fe, 2.4 size engine.
would work for only Toyotas
I had to jump my 08 sienna and now I've somehow engaged immobilizer. my key will not unlock the ignition switch to start the car. will this allow me to "reprogram" my key to the vehicle?
@@johnfoster4827 I cannot follow all the backdrop you have not included. Like key cannot activate ignition. You have not included your specific vehicle.
Hello I have a Mitsubishi delica and it won't go above the speed of 40 . Can you help me what might be the issue
Hey would this work on my toyota corolla hatchback 2016 ?
Hi, i did an engine swap along with the ecu.. my problem now is, car cannot start, cranking only. Im guessing the new ecu does not recognise the key.. will this trick works? Lexus GS300
Would this be a good option for lost keys on a 02 sequoia If I get a new key cut ?
2005 camry 2.4 motor swapped now the fuel pump doesn't kick when turning the key. Injectors don't fire either when fuel pump is hard wired. Trying this to avoid Toyota prices on reprogramming (pretty sure they're just doing this anyways) will update in 30 minutes.
1999 Toyota Solara with new key ignition cylinder with 2 new keys - i don't have the old keys - mentions at 1:43 that this can reprogram keys as well. I reset the ECM per his instructions. How can I program the new cylinder/new keys to the current ECM?
Hi, hope you can help. I have 1999 Avalon with security blinking and unable to start engine though it does crank. I also have a after market key ignition cylinder and new key. Where you unable to start your engine as well? If so, did this reset method work? i'm just afraid of shorting circuit and making a bigger problem and just confirming before proceeding. -thanks.
@Rey Badilla HOW DID YOU FIX THE PROBLEM?
Would you tell if this method will work on 2005 Lexus RX330 ? I have check engine light+ABS+VSC trac OFF … I just trying to Reset those lights
Thanks for sharing this tutorial sir how to reprogram ecu
Do you start the engine or just turn on the car and leave for 30 minutes?
Would this work for 2006 prius?