Installed blueprint 350 into my Monte Carlo SS!
HTML-код
- Опубликовано: 20 окт 2024
- Finally dropped in new blueprint 350 into my Monte Carlo ss and started the wiring repairs check it out! Like comment and subscribe.
#montecarlo #blueprint #supersport #ttop
Nice!!! I just dropped a Blueprint 350 in my 1985 Chevy K-10 Squarebody and i love it!!!
Nice I have an older BP350 in my 86 k10 she’s scoots down the road nicely! Mine is the vortec head BP350CTC1 it makes 387 hp and 414 ft lbs of torque!
Its coming along!! Thats a big step.
Just bought this block. Beautiful setup.
what headers did you use with the raised exhaust port blueprint heads
Nice Build ! I just put a motor in my 78 .
Blue print engines are the best😊😊😊
Yo my man what kind of radiator did you go with ????
Nice build man 🔥🔥🔥
I gotta 86 SS And Man this right here just gave me motivation had the car since I was 19 I’m 21 now going on 22
Start putting it together man! It’s worth it in the end.
@@trydecaddyz6831 forsho I’m planning on doing RUclips As Well just haven’t had the courage to do it but watching yo videos showed me some
@@dareal30rowslim1 I’ll definitely sub to the channel man and support it can be scary but it’s all fun anyway some people can be hateful but I just keep it moving
@@trydecaddyz6831 true and appreciate that is there other way I can get in contact with you just in case I have any questions or some
What's up bro. Nice project you have there. Beautiful engine. Question. I am getting the exact Blueprint more with the same serpentine set up in the front with AC compressor. My car does not have the actual AC set up yet. Can I still roll it without the bracketed compressor but not hooked up? It's a 67 Camaro.
Yessir
Any update on how the motor is doing today?
Did the 68600 headers fit on the blueprint 350 cid cruiser engine? Got some that blueprint engines recommended and they didn’t fit.
Yes they fit driver side you have to move vapor canister line to clear a little bit for heat purposes
Hows it running so far? Did the crate motor come fully assembled?
Yes it came in fully built, drip in and run just gotta adjust carb to your altitude mine was a little rich so we had to lean it out
Bro can you send me the link or the name for those headers? I have the longtube hooker headers..if you say that don't fit I will definitely go your route.
Headman 68600
@Everyday Terrance. thanks bro!!
Did you use the factory oil pressure sensor and coolant temperature sensor?
Yes I did but also a auxiliary set of gauges just to be sure.
Nice MC clean 350. What's the hp on that motor? What tranny does it have?
368 horse 360 torque I think still has 200r4 for now.
Was it built for proformance needs? Or was it just built as cheap as possible?
I drive it pretty hard and no issues
What part number of the headers I just bought that same engine 350 turn key and I’m dropping it into my 84 Monte Carlo SS
Headman 68600
@@trydecaddyz6831 thank you! How did you make out with that power steering I wonder if I’m gonna run into the same issue same car same engine. Mines an 84.
@@trydecaddyz6831 did you install the headers after the engine was in or did you put the headers on first then install the engine
Let me find the lines and fitting I had to order to make it work I’ll send those too.
@@trydecaddyz6831 thank you sir
Whats the part # on that blueprint crate engine. Is it the 341Hp
I think it is I gotta find paperwork for it.
Do use Dixie for any small parts i been using Dixie for years there prices are fair
I got tons of smalls from them definitely priced well and good quality.
How much did you get this 350 for?
It was like 6200 fully dressed drop in and run