Nice saw the steel city RC and had to click my fam from the 412, love me some Pittsburgh!! My Lebanon where I spent a lot of time as a kid, but up in Maine now!! Big sub, you got some great content it looks like ✌️🍻🍻
What is up man! Mt. Lebanon isn't far from me. Maine is beautiful I hear. Never have been. Thanks for the sub too. Lots of large scale RC on my channel. Appreciate you stopping by 👊 🤘
Probably a smart move being easy on the Rampage MT. Not the most stout of 5th scales. But such a blast to drive. Appreciate you stopping by to check out my truck 👊 🤘
Thanks! We had a blast down there. We actually spent a bit of time trying to smooth the smaller jumps out. Rampage took a few tumbles cos of off canter jumps. But did well overall.
Hi again. My redcat mt as stop working. It doesn't want to start. I put a new coil,new spark plug and now it doesn't have any sparks. I wonder if you could help me out with this.
@ronaldjones8797 I use the one from the old killer rc site. I have had zero issues with it. The Troybilt bits can be had at Lowes. What setup do you plan to use? Also, carrying a drill kinda sucks if not close to the car.
@@SteelCityRC it's an older XT with a Zenoah 29.5 cc. Basically a 30 size. Totally rebuilt (with what parts I can get from their website). I also have a Rovan Baja 5B with a ported Zenoah ESP. That one is heavily modded. And I have a Redcat Chimera. I will strongly suggest not to buy this hunk of garbage. The Chinese CY motor that came with it was bad. The coil was bad right out of the box. Numerous loose bolts. Air filter and Tx and Rx are garbage. Horrible design all the way around. Modified the receiver box to be able to charge battery. Air filter blocks one of the bolts. Right now I'm putting a Zenoah in it. All 3 of my rigs have a Dynamite kill switch. Also it's getting a Velocity stack and a shortened angle air filter from DDM. Also just ordered a Jet Pro pipe for it. So this $750 piece of crap is costing me an additional $650. And Redcats customer support is non existent. Matter of fact, I think thier guy Joey Lacey blocked me. They sell an inferior product and they don't stand behind it. About to order the Kraken Vesla 5. Hopefully better results. Thanks for your time and response. Keep bashing brother.
Thanks! Yes these are the Copperhead 2 wheels and tires. Holding up great. I keep an eye on the glue job holding the tires on frequently. But the tires are so soft for jumps. I use them on my Xmaxx too. Good all around tire in my opinion. Badlands MX43 are good on here too. Appreciate you stopping by 👊 🤘
@@rcbrooks3543 sup man. I use these one inch extenders. I can fit Losi MTXL wheels with no modification. I have yet to find a wheel that won't fit with these. Hardly rolls over anymore either. Here is www.dgiracing.com/mt-redcat-1-extenders-adaptor-for-hpi-baja-wheels/
@DaveKoko thank you so much! I have had this truck forever, it seems. I actually just put together some new wheels and tires to try on it this upcoming weekend. They should be super grippy lol. Stop on back to check them out. Appreciate you stopping by 👊 🤘
Hey GMan, what do you think of the durability of the driveline and chassis of the Redcats? That truck looks like it would make a good platform for a radical build up. Cool video buddy
Thanks Brian! Redcat is kinda junk IMO stock. There are no aftermarket companies to make parts. So I put as much Redcat upgrades as I could. Aluminum diff housings etc. Good bearings. Anything more than a ported g320 and it will break all the time. The side transmission gears are the worst. Break very easily. Was my first 5th scale.
Yeah, the seemingly lack of aftermarket parts is what pushed me to the Losi a couple of years ago when first venturing into 1/5th scale. But it was just a guess back then. Thanks for the info@@SteelCityRC
What's up man. The pipe is from Australia called Olimat Engineering. I love the sound. Had a DDM Dominator on it for a few years. Wanted to change it up.
Nice looking rig, it really rips. What 24 mm hubs are you using? Looking to get some Duratrax Hatchet tires&rims for my MT. I enjoy your videos, looking forward to the next. Thanks for sharing.
Hey what's up man! Thanks! I use DGI 1 inch wheel extenders on the MT. Can also use four rear baja 5B hexes if you don't want extensions. But I found some wheels will hit the steering knuckles without the extenders. Plus without it likes to roll over more because it made the width smaller without the stock MT wheels. Appreciate you stopping by 👊 🤘
@@restinpiecesrc5528 hello. I have never measured stock tires and width installed. But when I converted the hex to 24mm. I used DGI 1 inch extenders to make up for the lack of stock width with the different wheels. It is about the same width now and rarely rolls over.
Would you get a used rampage MT without a body, probably needs a new servo and definitely needs new battery and receiver/transmitter. Or, would you get a new Rovan 29cc baja? MT is $250, Rovan is $390. I plan to do light jumps on dirt, probably similar to the jumps in this or smaller.
That question all depends on what You want. The Rampage MT is a monster truck and has big wheels and 4x4. The Rovan 5b is a rear wheel drive buggy. Honestly the Rovan has more upgrades as it is cloned off the HPI baja. So many upgrades for a baja, Rampage is limited to Redcat upgrades.
What's up man! This truck does 45 mph. Not too bad for a 35 pound 5th scale gasser. Nitro is 8th scale. Much smaller platform. Appreciate you stopping by 👊 🤘
You are right the Rampage ran really good and is tough. Great video.
Hey thanks! Rampage MT is my favorite gasser for sure. Appreciate you stopping by 👊 🤘
Nice saw the steel city RC and had to click my fam from the 412, love me some Pittsburgh!!
My Lebanon where I spent a lot of time as a kid, but up in Maine now!!
Big sub, you got some great content it looks like
✌️🍻🍻
What is up man! Mt. Lebanon isn't far from me. Maine is beautiful I hear. Never have been. Thanks for the sub too. Lots of large scale RC on my channel. Appreciate you stopping by 👊 🤘
Hey ! Hey ! Me again , by any chance do you know of a upgraded clutch bell n shaft for the rampage ? And thanx much !
Unfortunately there is no upgrade for the Rampage MT clutch bell that I know of. Big downfall of Redcat. No aftermarket support
Awesome man! Great video!!
Thanks! We had a blast. Appreciate you stopping by 👊 🤘
I baby mine. Parts on this thing are cheaper that an f150 but I stopped pretty quick.
Probably a smart move being easy on the Rampage MT. Not the most stout of 5th scales. But such a blast to drive. Appreciate you stopping by to check out my truck 👊 🤘
Good times brother! That truck always runs well! Thanks for sharing man!
Thanks! We had a blast down there. We actually spent a bit of time trying to smooth the smaller jumps out. Rampage took a few tumbles cos of off canter jumps. But did well overall.
Hi again. My redcat mt as stop working. It doesn't want to start. I put a new coil,new spark plug and now it doesn't have any sparks. I wonder if you could help me out with this.
@@cedricmallet8621 there may be a problem with your kill switch.
I was thinking about purchasing the hex drive starter for my XT. Have you ever had any issues with it?
@ronaldjones8797 I use the one from the old killer rc site. I have had zero issues with it. The Troybilt bits can be had at Lowes. What setup do you plan to use? Also, carrying a drill kinda sucks if not close to the car.
@@SteelCityRC it's an older XT with a Zenoah 29.5 cc. Basically a 30 size. Totally rebuilt (with what parts I can get from their website). I also have a Rovan Baja 5B with a ported Zenoah ESP. That one is heavily modded. And I have a Redcat Chimera. I will strongly suggest not to buy this hunk of garbage. The Chinese CY motor that came with it was bad. The coil was bad right out of the box. Numerous loose bolts. Air filter and Tx and Rx are garbage. Horrible design all the way around. Modified the receiver box to be able to charge battery. Air filter blocks one of the bolts. Right now I'm putting a Zenoah in it. All 3 of my rigs have a Dynamite kill switch. Also it's getting a Velocity stack and a shortened angle air filter from DDM. Also just ordered a Jet Pro pipe for it. So this $750 piece of crap is costing me an additional $650. And Redcats customer support is non existent. Matter of fact, I think thier guy Joey Lacey blocked me. They sell an inferior product and they don't stand behind it. About to order the Kraken Vesla 5. Hopefully better results. Thanks for your time and response. Keep bashing brother.
Awesome video G-man killer bash session and Launches 🚀 with the Rampage.. she definitely took a good beating too great job thumbs up 👍
Thanks Scoot. My favorite basher for sure. Appreciate you stopping by 👊 🤘
Hell yeah you’re having all the fun👍🔥💨
Ahahahaha what a blast this truck is to drive. Appreciate you stopping by 👊 🤘
Nice rock crusher
Heck yeah! Fun truck to bash. Thanks for watching 👊🤘
Good stuff. I see you are running Arrma wheels and tires in this one. Are they copperheads and how did they hold up to the torque ?
Thanks! Yes these are the Copperhead 2 wheels and tires. Holding up great. I keep an eye on the glue job holding the tires on frequently. But the tires are so soft for jumps. I use them on my Xmaxx too. Good all around tire in my opinion. Badlands MX43 are good on here too. Appreciate you stopping by 👊 🤘
@@SteelCityRC what wheel adaptors are you running with the copperheads?
@@rcbrooks3543 sup man. I use these one inch extenders. I can fit Losi MTXL wheels with no modification. I have yet to find a wheel that won't fit with these. Hardly rolls over anymore either. Here is www.dgiracing.com/mt-redcat-1-extenders-adaptor-for-hpi-baja-wheels/
Nice man! Running like a champ💯
Yo thanks Dave! The mighty Rampage MT was my first 5th scale. Always has a spot in my lineup. Appreciate you stopping by 👊 🤘
New sub here. Great videos
@DaveKoko thank you so much! I have had this truck forever, it seems. I actually just put together some new wheels and tires to try on it this upcoming weekend. They should be super grippy lol. Stop on back to check them out. Appreciate you stopping by 👊 🤘
What pipe do
You have on that?
What is up!! That is an Olimat pipe on there. Love it!!
Nice!!! Are these the same wheel size as what comes on the XT?
What's up? I really am not sure the size of XT wheels. Never had one. These current wheels are from an Arrma Kraton 8S. They are nice and cushiony.
Hey GMan, what do you think of the durability of the driveline and chassis of the Redcats? That truck looks like it would make a good platform for a radical build up. Cool video buddy
Thanks Brian! Redcat is kinda junk IMO stock. There are no aftermarket companies to make parts. So I put as much Redcat upgrades as I could. Aluminum diff housings etc. Good bearings. Anything more than a ported g320 and it will break all the time. The side transmission gears are the worst. Break very easily. Was my first 5th scale.
Yeah, the seemingly lack of aftermarket parts is what pushed me to the Losi a couple of years ago when first venturing into 1/5th scale. But it was just a guess back then. Thanks for the info@@SteelCityRC
Hey my friend, we're did you get your exhaust pipe from and name of it? And what's your transmission gear set up ?
What's up man. The pipe is from Australia called Olimat Engineering. I love the sound. Had a DDM Dominator on it for a few years. Wanted to change it up.
@@SteelCityRC oh ok that's what's up. Out of the two, what's your take on them
Nice run bud, redcat mt looking good 👍👊🏻
Sup man. Thanks. The MT is a fun basher for sure. Thanks for checking out my video 👊🤘
Nice rip bud 👊🏽
Yo what is up! Thanks man! Appreciate you stopping by 👊 🤘
Nice looking rig, it really rips. What 24 mm hubs are you using? Looking to get some Duratrax Hatchet tires&rims for my MT. I enjoy your videos, looking forward to the next. Thanks for sharing.
Hey what's up man! Thanks! I use DGI 1 inch wheel extenders on the MT. Can also use four rear baja 5B hexes if you don't want extensions. But I found some wheels will hit the steering knuckles without the extenders. Plus without it likes to roll over more because it made the width smaller without the stock MT wheels. Appreciate you stopping by 👊 🤘
Thanks man! I appreciate the info..never thought about the roll over potential with the smaller tires..keep up the awesome content 👍😁
@@1NICE88GTA thanks brother!!
@@SteelCityRC have you measured how wide it is without the tires on it stock? I've been curious how much the tires attribute to the overall width
@@restinpiecesrc5528 hello. I have never measured stock tires and width installed. But when I converted the hex to 24mm. I used DGI 1 inch extenders to make up for the lack of stock width with the different wheels. It is about the same width now and rarely rolls over.
Would you get a used rampage MT without a body, probably needs a new servo and definitely needs new battery and receiver/transmitter. Or, would you get a new Rovan 29cc baja? MT is $250, Rovan is $390. I plan to do light jumps on dirt, probably similar to the jumps in this or smaller.
That question all depends on what You want. The Rampage MT is a monster truck and has big wheels and 4x4. The Rovan 5b is a rear wheel drive buggy. Honestly the Rovan has more upgrades as it is cloned off the HPI baja. So many upgrades for a baja, Rampage is limited to Redcat upgrades.
🙏💯✊️💪👍
Thanks for watching, Caleb!! 👊🤘
Why are these gas trucks are so slow compared to nitro engines
What's up man! This truck does 45 mph. Not too bad for a 35 pound 5th scale gasser. Nitro is 8th scale. Much smaller platform. Appreciate you stopping by 👊 🤘
@@SteelCityRC 45 stock?